Skip to the content
2 layers77.5 × 31.8 mmJunior computer display, the printed circuit board in 3D

A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

Size
77.5 × 31.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
19
Pads
77
Tracks, vias
232, 0
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
1 Oct 2020
Updated
21 Dec 2024

Overview

Junior computer display is an open-source printed circuit board by laurent-fr, from the laurent-fr/junior_computer_replica repository on GitHub. It is a 2-layer board of 77.5 × 31.8 mm with 11 parts on 19 nets, routed with 232 tracks and 0 vias.

It belongs with the lEDs and displays boards of this library.

README

README.md

Junior Computer Replica

Junior Computer Front

Junior Computer Back

The Junior Computer is a 6502 SBC made by Elektor in 1980. It looks a lot like a KIM-1.

This is a replica PCB I made with KiCAD.

The best source of information for this computer is Elektor Magazine from 80's , but you can find a lot on this website : http://retro.hansotten.nl/6502-sbc/elektuur-junior/

This board is not a 100% accurate replica, because I have added directly on the PCB a few updates published later by Elektor :

  • a fix for memory decoding needed for the expansion board
  • the main decoupling capacitor C2 was on wrong side of S25 (activate display) which could reset the computer
  • a simple reset circuit with a resistor and a capacitor

I also replaced the 2708 EPROM by a 2716, which avoid the need of an hard to find EPROM & EPROM programmer, and has the big benefit of reducing the required power supplies from 3 (+5,-5,+12) to only +5V.

This work is licenced under CC BY-NC-SA (Attribution-NonCommercial-ShareAlike)

BOM

QtyReferenceValueComment
1C110p
1C247µ 6V tantale
2C3, C4100n MKH
8C5...C9, C10, C11, C141µ 16V tantale
1C12470nF MKH
2D1, D31N4148
1IC1MC6502
1IC1074LS01
1IC11ULN2003
1IC22716
1IC3MC6532probably the first part to look at !
2IC4 IC52114static RAM, search on Ebay
2IC7 IC674LS145
1IC8NE556
1IC974LS00
1J2DIN41612 32 A+C angled male
1J3DIN41617-31 straight female
2R17 R192k2
2R18 R2068k
1R1330K
6R2 R3 R4 R16 R14 R153k3
2R22 R211k
1R23820k
1R54k7
1R6330
7R7 R8 R9 R10 R12 R13 R1168
21S1…S23Digitast 12.7mm16 black, 4 red, 1 red with integrated LED, 2 blue, but see below
1S24DPDT lever switchwith soldering lugs
1S25SPDT lever switchwith soldering lugs
1X.Tal11Mhzcan be hard to find !
3Socket DIP-14
3Socket DIP-16
2Socket DIP-18
1Socket DIP-24
2Socket DIP-40
6Di1 ... Di6MAN4640A7 segment display

IF you cannot find 2114 RAMs , you can try the small board on "board adapter" folder (warning : not tested !) which should allow to use a 6116 RAM instead and plugs into the 2114 sockets

The Digitast keys (https://www.digikey.com/catalog/en/partgroup/digitast-series/15959) are the most expensives parts of this project. You can also use square tactile switchs instead (but it's not as pretty !)

An other thing to consider is the marking : the black keys need white marking, which can be hard to do. So think of how you will do the marking before choosing the colors of the keys !

Ordering the PCB

Use you favorite online PCB seller, and order 2 double-sided PCBs (display + computer) from the KiCad output files.

The real ones from Elektor where blue on component side and red on solder side, but if you order a blue PCB it will be close enough (and very nice).

Building the computer

The building is pretty straightforward (look at the original documentation). Components are soldered on one side, buttons and disply on the other side.

S24 and S25 switchs needs wires from the switchs lugs to the PCB (I used cutoff of resistor leads)

To connect the display to the main board, I used long SIL connectors (15-20mm long) soldered on both side, then I bent the display to ~30°

Don't forget the two small wire jumpers on front side : one from ground to letter "D" and the other one from K6 to the center pin.

If you want to use the file sticker-juniorcomputer.svg, first install the font "Microgramma D Extended Bold" on your system.

Programming the EPROM

I use a TL866 II plus for this, but anything that works is OK.

Program the 2716 with the file 2716_junior_monitor_ram_05_1980.bin

First tests

The power supply is available on both connectors, you just need 0v and +5V (1amp should be more than enough).

All the display should light up (check that the DISPLAY switch is ON). If you see some display ON, some display OFF, it could be a bad MC6532 (don't ask how I know that ...)

If nothing happens, press the reset switch to start the computer.

Typing numbers on keyboard should update the display.

You can find test programs on http://retro.hansotten.nl

Going further

It would be great to be able to load and save data, and also to have a serial terminal for typing programs. It's exactly the purpose of the Junior Interface board ! Look into the folder "junior-interface" for more infos !

Now I'm sure you want to run BASIC on the Junior, no problem, just build the memory expansion from "junior-universal-memory" folder and you're good to go !

Status

Working

  • junior-computer : the computer, built and tested OK
  • junior-computer-display: the 7 segments display, built and tested OK
  • junior-interface : the 2nd board adding various I/O to the computer, built and tested OK
  • junior-internal-conn : internal bus between computer and interface, built and tested OK
  • junior-internal-bus : a small PCB for linking the computer and the interface board, built and tested OK
  • junior-bus : Elektor expansion bus. Not tested, built and tested OK
  • junior-universal-memory : a RAM/EPROM board for the computer, built and tested OK

Not tested

  • ram-adapter : replace 2x2114 by 1x6116 RAM. Not tested
text
Any question ? --> Mastodon @LaurentFr@piaille.fr

Parts

11
QtyValueFootprintReferences
6MAN4640Aelektor:7SEGMENTDi1, Di2, Di3, Di4, Di5, Di6
1Displayelektor:Conn-Display-TopJ1

The 7 most common of 11 parts.

More from laurent-fr/junior_computer_replica

7
  • 2 layers217.2 × 113 mmJunior interface, the printed circuit board in 3D

    Junior interface

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    120 parts14
  • 2 layers217.2 × 113 mmJunior computer, the printed circuit board in 3D

    Junior computer

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    86 parts14
  • 2 layers160 × 100 mmJunior universal memory, the printed circuit board in 3D

    Junior universal memory

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    38 parts14
  • 2 layers116.8 × 100 mmJunior bus, the printed circuit board in 3D

    Junior bus

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    15 parts14
  • 2 layers91.4 × 19.7 mmJunior interface conn, the printed circuit board in 3D

    Junior interface conn

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    9 parts14
  • 2 layers34.3 × 33 mmRam adapter, the printed circuit board in 3D

    Ram adapter

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    5 parts14
  • 2 layers99.1 × 46.8 mmJunior internal bus, the printed circuit board in 3D

    Junior internal bus

    laurent-fr/junior_computer_replica

    A replica of the Junior Computer (a KIM-1 clone) published by Elektor in the 80's

    2 parts14

Similar boards

  • 2 layers60 × 30 mmController, the printed circuit board in 3D

    Controller

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    11 parts3kApache-2.0
  • 2 layers103 × 30.5 mmTS Front Endcap, the printed circuit board in 3D

    TS Front Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    11 parts1.3kMIT
  • 2 layers26 × 30 mmExpansion Card, the printed circuit board in 3D

    Expansion Card

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    11 parts1.1kCC-BY-4.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    11 parts1kGPL-3.0
  • 2 layers10 × 20 mm2 connector Sensor Board, the printed circuit board in 3D

    2 connector Sensor Board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    11 parts915
  • 2 layersFet module, the printed circuit board in 3D

    Fet module

    ByteWelder/Decktility

    A handheld PC

    11 parts855CC-BY-SA-4.0
  • 2 layers47 × 33 mmSevensegment led display module, the printed circuit board in 3D

    Sevensegment led display module

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    11 parts803MIT
  • 2 layers42.5 × 36.8 mmDevboard, the printed circuit board in 3D

    Devboard

    basilfx/TRADFRI-Hacking

    Hacking IKEA TRÅDFRI products, such as light bulbs, window blinds and other accessories.

    11 parts743CC-BY-4.0

Questions

How big is the Junior computer display PCB?

It measures 77.5 × 31.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Junior computer display use?

11 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Junior computer display KiCad files?

From the laurent-fr/junior_computer_replica repository on GitHub, at the commit this page was made from: the board is junior-computer-display/junior-computer-display.kicad_pcb and its schematic junior-bus/junior-bus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Junior computer display design in my own project?

Its repository states no licence, so its author keeps all rights: ask laurent-fr before reusing the design.