Skip to the content
2 layersWeather station, the printed circuit board in 3D

This repoistory holds my current project for designing a home monitoring solution for temperature, humidity, and eventually the status of the plants in my office.

Copper layers
2
Thickness
1.6 mm
Parts
3
Nets
15
Pads
54
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 6 (file 20211014)
Created
1 May 2022
Updated
1 May 2022

Overview

Weather station is an open-source printed circuit board by latonis, from the latonis/weather-station repository on GitHub. It is a 2-layer board with 3 parts on 15 nets.

It is built around the DHT11. It belongs with the home automation and IoT boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

weather-station

This repoistory holds my current project for designing a home monitoring solution for temperature, humidity, and eventually the status of the plants in my office. Eventually, I would like to use an ESP32 or similar Wi-Fi enabled chip to host a small webserver or send notifications to alert me when desired specifications are met.

Features

  • measure temperature in Fahrenheit
  • measure humidity
  • display these measurements visually

Goal Features

  • measure soil moisture
  • alert when soil is too dry
  • alert when temperature is below a set value
  • alert when temperature is above a set value
  • alert when humidity is above a set value

Parts List (continually updated)

  • Arduino Nano (Atmega 168P)
  • LCD1602 Module
  • DHT11 Sensor
  • Many jumper wires (for the time being)

Schematic

All of the schematics can be found in the sch/ directory.

Code

Parts

3
QtyValueFootprintReferences
1Arduino_Nano_Atmega168pasch:Arduino_nano_cloneU1
1DHT11Sensor:Aosong_DHT11_5.5x12.0_P2.54mmU2
1WC1602ADisplay:WC1602ADS1

Similar boards

  • 2 layers96.6 × 82.8 mmStarbie, the printed circuit board in 3D

    Starbie

    SharKingStudios/Starbie

    Half-Life Week 1 Example Project

    11 parts28MIT
  • 2 layers100 × 50 mmConveyor belt pcb, the printed circuit board in 3D

    Conveyor belt pcb

    lansidev/conveyor-belt

    Miniature 3D printed conveyor belt for simulation and fun working with sensors, all controllable with Raspberry Pi

    22 parts9MIT
  • 2 layers93 × 20 mmWiFi VFD, the printed circuit board in 3D

    WiFi VFD

    ciisaichan/WiFi-VFD

    开源的ESP8266驱动VFD屏电路,支持BiliBili粉丝数、时间、温度、湿度

    23 parts8MIT
  • 2 layersOpenMQTTGatewayPCB, the printed circuit board in 3D

    OpenMQTTGatewayPCB

    ebrithiljonas/OMG_PCB

    All in One PCB for the OpenMQTTGateway Project

    36 parts7GPL-3.0
  • 2 layers62 × 19.3 mmSniffingTrinket, the printed circuit board in 3D

    SniffingTrinket

    GeorgK/SniffingTrinket

    A room climate monitor using the Adafruit Trinket Pro

    23 parts6GPL-3.0
  • 2 layersArduino relay, the printed circuit board in 3D

    Arduino relay

    bhaskar9980/Guardian

    Guardian is an advanced, fully automated hydroponics system designed to optimize plant growth and maximize yield.

    58 parts5MIT
  • 2 layers100 × 43.5 mmFirefly, the printed circuit board in 3D

    Firefly

    Twistx77/Firefly

    Open WIFI-enabled RGB lamp with temperature, humidity, suspended air particles and eCO2 sensors.

    33 parts5GPL-3.0
  • 2 layers30.5 × 77.5 mmProyecto sensor temperatura, the printed circuit board in 3D

    Proyecto sensor temperatura

    unla-investigacion-desarrollo/ecosistema-iot

    Antes de desarrollar el sistema final, realizamos una etapa de exploración donde investigamos y experimentamos con las siguientes tecnologías:

    8 parts5

Questions

What parts does the Weather station use?

3 parts, built around the DHT11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Weather station KiCad files?

From the latonis/weather-station repository on GitHub, at the commit this page was made from: the board is sch/weather_station/weather_station.kicad_pcb and its schematic sch/weather_station/weather_station.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Weather station design in my own project?

Its repository states no licence, so its author keeps all rights: ask latonis before reusing the design.