

CSwitch CalCoilV2
- Size
- 58.4 × 30.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 47
- Nets
- 32
- Pads
- 127
- Tracks, vias
- 198, 19
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 27 Nov 2024
- Updated
- 10 Jun 2025
Overview
CSwitch CalCoilV2 is an open-source printed circuit board by LASSITOS, from the LASSITOS/LEM_LASSITOS repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 58.4 × 30.5 mm with 47 parts on 32 nets, routed with 198 tracks and 19 vias.
It is built around the TLP3553 and PCA8574D. Its parts include 26 resistors, 5 ICs, 5 connectors and 4 diodes.
Main components
2README
README.mdLEM_LASSITOS
This repository contains the open source code, and plans for the LEM sounder develped as part of the LASSITOS project.
I should add some informations here
Construction of LEM
Operating the LEM
LEM commands
Data link LEM and UAV
The LEM Radio Link (LoRa 900MHz) is used to communicate to the LEM during measurements. The user can send control commands (START, STOP, SETFREQ,... ) connecting via serial bluetooth or USB serial to the LEM_Base. The LEM commands are transmitted over a own NMEA message ($LEMMS,...). This allows to separate them from the RTK message stream that is transmitted over the same channel. The RTK messages can be passed to the LEM_Base over Serial UART (3.3V) or USB. Only one GPS base station can be used if the RTK stream is split on the laptop between then LEM and UAV. See schematics below for passing RTK correction over UART (option1) or splitting on Laptop and passing over USB (Option2).
Data download
ESP32 data: Laser, IMU, general
LEM raw data
Data Postprocessing
Parts
47| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R4, R10, R11, R18, R19, R20, R21, R22, R23, R24, R25, R26 |
| 4 | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 | |
| 4 | 100k | Resistor_SMD:R_0805_2012Metric | R5, R6, R7, R12 |
| 4 | 200 | Resistor_SMD:R_0805_2012Metric | R1, R8, R9, R15 |
| 4 | TLP3553 | library_components:TLP3553ATP1_F | U2, U3, U4, U5 |
| 3 | 12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm | JP1, JP2, JP3 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | 325 | Resistor_SMD:R_0805_2012Metric | R16, R17 |
| 2 | 5-104363-3 | library_components:5-104363-3 | J1, J2 |
| 2 | 750 | Resistor_SMD:R_0805_2012Metric | R13, R14 |
| 2 | QIWC | library_components:CONN_BM04B-SRSS-TB(LF)(SN) | J4, J5 |
| 1 | Blue | library_components:LEDC2012X85N | LED1 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Green | library_components:LEDC2012X85N | LED4 |
| 1 | PCA8574 | library_components:PCA8574PW_118 | U1 |
| 1 | REd | library_components:LEDC2012X85N | LED2 |
| 1 | Yellow | library_components:LEDC2012X85N | LED3 |
More from LASSITOS/LEM_LASSITOS
5- 2 layers124.5 × 68 mm

- 2 layers78 × 47 mm

- 2 layers126 × 63 mm

- 2 layers99.1 × 61 mm

- 2 layers13.2 × 80.8 mm

Similar boards
- 2 layers115 × 100 mm

Cog1
diegodemarco/cog1
cog1 is an open-source industrial IoT gateway (hardware and software) built as a motherboard hosting an Orange Pi Zero 3 Linux SBC.
133 parts6MIT - 2 layers30 × 61.3 mm

- 2 layers114 × 61.4 mm

- 2 layers80 × 35 mm

V0 Display RP2040
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group
47 parts1.1kGPL-3.0 - 2 layers100 × 66.7 mm

MacroPad1
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
47 parts915 - 2 layers100 × 100 mm

- 2 layers36.3 × 99.1 mm

- 2 layers50 × 20.5 mm

Questions
How big is the CSwitch CalCoilV2 PCB?
It measures 58.4 × 30.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the CSwitch CalCoilV2 use?
47 parts, built around the TLP3553 and PCA8574D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the CSwitch CalCoilV2 KiCad files?
From the LASSITOS/LEM_LASSITOS repository on GitHub, at the commit this page was made from: the board is Construction/KiCAD/CSwitch_CalCoilV2/CSwitch_CalCoilV2.kicad_pcb and its schematic Construction/KiCAD/CSwitch_CalCoilV2/CSwitch_CalCoilV2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the CSwitch CalCoilV2 design in my own project?
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).