Skip to the content
2 layers126 × 63 mmCommonModeFilter CSwitch v2, the printed circuit board in 3D

CommonModeFilter CSwitch v2

LASSITOS/LEM_LASSITOS
Size
126 × 63 mm
Copper layers
2
Thickness
1.6 mm
Parts
86
Nets
99
Pads
253
Tracks, vias
469, 54
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
27 Nov 2024
Updated
10 Jun 2025

Overview

CommonModeFilter CSwitch v2 is an open-source printed circuit board by LASSITOS, from the LASSITOS/LEM_LASSITOS repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 126 × 63 mm with 86 parts on 99 nets, routed with 469 tracks and 54 vias.

It is built around the BM04B-SRSS-TB(LF)(SN). Its parts include 32 resistors, 18 switches, 4 capacitors, 4 connectors and 2 inductors.

Main components

1

README

README.md

LEM_LASSITOS

This repository contains the open source code, and plans for the LEM sounder develped as part of the LASSITOS project.

I should add some informations here

Construction of LEM

Operating the LEM

LEM commands

Data link LEM and UAV

The LEM Radio Link (LoRa 900MHz) is used to communicate to the LEM during measurements. The user can send control commands (START, STOP, SETFREQ,... ) connecting via serial bluetooth or USB serial to the LEM_Base. The LEM commands are transmitted over a own NMEA message ($LEMMS,...). This allows to separate them from the RTK message stream that is transmitted over the same channel. The RTK messages can be passed to the LEM_Base over Serial UART (3.3V) or USB. Only one GPS base station can be used if the RTK stream is split on the laptop between then LEM and UAV. See schematics below for passing RTK correction over UART (option1) or splitting on Laptop and passing over USB (Option2).

Schematic data link wiht one RTK base station Schematic data link wiht 2 RTK base stations

Data download

ESP32 data: Laser, IMU, general

LEM raw data

Data Postprocessing

Parts

86
QtyValueFootprintReferences
1811-7A801S_TOSlibrary_components:TLP3546ATP1_FOK1, K2, K3, K4, K5, K6, K7, K10, K11, K12, K13, K14, K15, K16, K17, K18 +2
18250Resistor_SMD:R_0805_2012MetricR6, R7, R15, R16, R19, R20, R21, R22, R23, R24, R26, R27, R28, R30, R31, R32 +2
8Conn_01x01Connector_Wire:SolderWire-1sqmm_1x01_D1.4mm_OD2.7mmFOUT0, FOUT1, OUTC1, OUTC2, OUTC3, OUTC4, OUTC5, OUTC6
6100kResistor_SMD:R_0805_2012MetricR1, R5, R17, R18, R25, R29
4 MountingHole:MountingHole_2.7mmH3, H4, H5, H6
4CAP_ECWFA_STRAIGHT_23.8LX13.5TX19.3H_PANlibrary_components:ECW-F2395JAC1, C2, C3, C4
4NPResistor_SMD:R_0805_2012MetricR4, R10, R11, R13
3 MountingHole:MountingHole_2.7mm_M2.5H8, H9, H10
312Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mmJP1, JP2, JP3
210kResistor_SMD:R_0805_2012MetricR2, R3
22.46Resistor_SMD:R_2512_6332MetricR12, R14
2BM04B-SRSS-TB(LF)(SN)library_components:CONN_BM04B-SRSS-TB(LF)(SN)J3, J4
2CONN_5-104363-3_TYCOlibrary_components:5-104363-3J1, J2
2WE74443634700library_components:WE74443634700L1, L2
1 MountingHole:MountingHole_2.7mm_M2.5H7
1GN0Connector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmGN0
1GN1Connector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmGN1
1IN0AConnector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmIN0A1
1IN0BConnector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmIN0B1
1IN1AConnector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmIN1A1
1IN1BConnector_Wire:SolderWire-0.75sqmm_1x01_D1.25mm_OD2.3mmIN1B1
1TSSOP16_SOT403-1_NXPlibrary_components:PCA8574PW_118U1

More from LASSITOS/LEM_LASSITOS

5
  • 2 layers99.1 × 61 mmMSP430, the printed circuit board in 3D

    MSP430

    LASSITOS/LEM_LASSITOS

    61 partsCC0-1.0
  • 2 layers13.2 × 80.8 mmTxSense12, the printed circuit board in 3D

    TxSense12

    LASSITOS/LEM_LASSITOS

    9 partsCC0-1.0

Similar boards

  • 4 layers37 × 34.3 mmReadout 60pin, the printed circuit board in 3D

    Readout 60pin

    opentac/opentac

    OpenTac: open tools to design, fabricate, read and simulate flex-PCB tactile skins that sense normal and shear force, for any robot surface.

    55 parts92MIT
  • 6 layers100 × 70 mmSa800u baseboard hw, the printed circuit board in 3D

    Sa800u baseboard hw

    antmicro/snapdragon-845-baseboard

    https://antmicro.com/blog/2022/04/open-source-snapdragon-845-baseboard/

    616 parts70Apache-2.0
  • 10 layers120 × 120 mmK410t devboard, the printed circuit board in 3D

    K410t devboard

    antmicro/kintex-410t-devboard

    This repository contains open hardware design files for a devkit created for AMD-Xilinx Kintex-7 K410T FPGA.

    1,020 parts46Apache-2.0
  • 12 layers165 × 102.7 mmData center rdimm ddr5-tester, the printed circuit board in 3D

    Data center rdimm ddr5-tester

    antmicro/rdimm-ddr5-tester

    FPGA-based DRAM tester supporting RDIMM DDR5 memories

    797 parts44Apache-2.0
  • 4 layers108 × 50 mmFED3, the printed circuit board in 3D

    FED3

    KravitzLabDevices/FED3

    Feeding Experimentation Device version 3

    114 parts36GPL-3.0
  • 4 layers53.2 × 53.2 mmSmart lcc, the printed circuit board in 3D

    Smart lcc

    variegated-coffee/open-lcc-board

    Schematics and PCB files for the Open LCC hardware

    117 parts30CERN-OHL-P-2.0
  • 4 layers100 × 100 mmD1600e psu breakout board, the printed circuit board in 3D

    D1600e psu breakout board

    antmicro/d1600e-psu-breakout

    Breakout board for DELL D1600E-S0 Power Supply Unit

    237 parts20Apache-2.0
  • 6 layers69 × 54 mmOpen control board, the printed circuit board in 3D

    Open control board

    variegated-coffee/all-purpose-espresso-controller

    Espresso electronics are usually proprietary affairs with little to no expandability. The purpose of this project is to give everyone an open source alternative with lots of features and flexibility.

    201 parts14CERN-OHL-P-2.0

Questions

How big is the CommonModeFilter CSwitch v2 PCB?

It measures 126 × 63 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CommonModeFilter CSwitch v2 use?

86 parts, built around the BM04B-SRSS-TB(LF)(SN). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CommonModeFilter CSwitch v2 KiCad files?

From the LASSITOS/LEM_LASSITOS repository on GitHub, at the commit this page was made from: the board is Construction/KiCAD/CommonModeFilter_CSwitch_v2/CommonModeFilter_CSwitch_v2.kicad_pcb and its schematic Construction/KiCAD/CSwitch_CalCoilV2/CSwitch_CalCoilV2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CommonModeFilter CSwitch v2 design in my own project?

Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).