Skip to the content
2 layers32 × 25.5 mmEspxpansion, the printed circuit board in 3D

This is an expansion module for the Hackxpansion console which adds the ESP32-C6-MINI.

Size
32 × 25.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
39
Pads
97
Tracks, vias
96, 25
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
15 Sep 2026
Updated
18 Oct 2026

Overview

Espxpansion is an open-source printed circuit board by Las-Vejas, from the Las-Vejas/espxpansion repository on GitHub. It is a 2-layer board of 32 × 25.5 mm with 13 parts on 39 nets, routed with 96 tracks and 25 vias.

It is built around the ESP32-C6-MINI-1. Its parts include 5 resistors, 2 connectors, 1 capacitor and 1 IC. It belongs with the ESP32 and RISC-V boards of this library.

Main components

1

README

README.md

espxpansion

This is an expansion module for the Hackxpansion console which adds the ESP32-C6-MINI.

The ESP can communicate to the Console using UART. There is also a breakout on the side of the board with the UART pins along with power and ground pins. programming can also be done via uart. There are also buttons for boot and reset.

The case is 3d printed, and uses 2 M2 screws to screw into the pcb.

schem pcb 3d

Parts

13
QtyValueFootprintReferences
310kResistor_SMD:R_0402_1005MetricR3, R4, R5
110uFCapacitor_SMD:C_0402_1005MetricC2
11kResistor_SMD:R_0402_1005MetricR1
120kResistor_SMD:R_0402_1005MetricR2
1BOOTButton_Switch_SMD:SW_Push_SPST_NO_Alps_SKRKBOOT
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2
1ESP32-C6-MINI-1RF_Module:ESP32-C6-MINI-1U1
1RESETButton_Switch_SMD:SW_Push_SPST_NO_Alps_SKRKRESET
1~Hackxpansion:Male_ModuleJ1

The 11 most common of 13 parts.

Similar boards

  • 4 layers86 × 56 mmRv1106, the printed circuit board in 3D

    Rv1106

    EPSILON0-dev/Raven1106

    Raspberry Pi-style SBC based on the Rockchip RV1106G3

    217 parts4
  • 2 layers25 × 22.6 mmUSlime, the printed circuit board in 3D

    USlime

    ReSummit/uSlime

    Micro form of SlimeVR trackers using BNO085

    48 parts4GPL-3.0
  • 2 layers27.9 × 41.7 mmModbus Adapter, the printed circuit board in 3D

    Modbus Adapter

    tomasmcguinness/esp32-modbus-serial-adapter

    The hardware folder contains a KiCad PCB design, designed around the ESP32-C6-MINI-1. Both the antenna and non-antenna (U1) versions will work here due to the location of the ESP32.

    23 parts4
  • 2 layers40 × 22.1 mmKaze, the printed circuit board in 3D

    Kaze

    Las-Vejas/Kaze

    A very powerful surrounding sensor

    44 parts3MIT
  • 2 layers50 × 45.3 mmTempic HW, the printed circuit board in 3D

    Tempic HW

    jernej13/Tempic

    Small solarpowered ESP32 based indoor/outdoor wifi weather station.

    61 parts2MIT
  • 2 layers30.4 × 52.6 mmMBus ESP Adapter, the printed circuit board in 3D

    MBus ESP Adapter

    tomasmcguinness/matter-esp32-mbus-adapter

    An ESP32-C6 adapter board for wired M-Bus (EN 13757) meters, with firmware examples that expose meter readings to a Matter fabric over Thread.

    42 parts2
  • 2 layers105 × 90 mmWs uc06, the printed circuit board in 3D

    Ws uc06

    wildsystems/ws-uc06

    Custom ESP32-C6 development board with power input protection, relay outputs, opto-isolated I/O, NTC sensor input, and JTAG debugging. Designed as a DIY-friendly controller base.

    84 parts2
  • 2 layers46.3 × 43.4 mmCarbon, the printed circuit board in 3D

    Carbon

    Enderman8843/Carbon

    Carbon is an open-source indoor air quality sensing board designed for accurate VOC, temperature, and humidity monitoring.

    38 parts1

Questions

How big is the Espxpansion PCB?

It measures 32 × 25.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Espxpansion use?

13 parts, built around the ESP32-C6-MINI-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Espxpansion KiCad files?

From the Las-Vejas/espxpansion repository on GitHub, at the commit this page was made from: the board is pcb/espxpansion.kicad_pcb and its schematic pcb/espxpansion.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Espxpansion design in my own project?

Its repository states no licence, so its author keeps all rights: ask Las-Vejas before reusing the design.