
Lpc812-nrf24l01-receiver
laneboysrc/nrf24l01-rc
nRF24-based RC car receiver, compatible with HobbyKing HK310 and Turnigy 3XS

nRF24-based RC car receiver, compatible with HobbyKing HK310 and Turnigy 3XS
Lpc812-nrf24l01-8ch receiver is an open-source printed circuit board by laneboysrc, from the laneboysrc/nrf24l01-rc repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 21 × 21 mm with 23 parts on 30 nets, routed with 210 tracks and 7 vias.
It is built around the LPC812M101JDH20. Its parts include 8 connectors, 6 capacitors, 3 ICs, 1 resistor and 1 diode. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
The source files are for Kicad.
For convenience the schematics are also available as PDF.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 18p | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C6, C7 |
| 2 | 1k x 4 | Resistor_SMD:R_Array_Concave_4x0603 | RN1, RN2 |
| 2 | 47u/6.3V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C5 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C4 |
| 1 | 12MHz | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | 1u/16V | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1 |
| 1 | 270 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1 |
| 1 | BIND/ISP | tact-switch:Tact switch 6x4x3 | SW1 |
| 1 | CH1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | CH2/Rx | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | CH3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | CH4 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | CH5/Tx | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | CH6 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | CH7 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | CH8 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | LPC812M101JDH20 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | MCP1703A-3302_SOT23 | Package_TO_SOT_SMD:SOT-23 | U1 |
| 1 | NRF24L01_E01_ML01 | nordic-semiconductor:nrf24l01-E01-ML01IPX | U3 |

laneboysrc/nrf24l01-rc
nRF24-based RC car receiver, compatible with HobbyKing HK310 and Turnigy 3XS

laneboysrc/nrf24l01-rc
nRF24-based RC car receiver, compatible with HobbyKing HK310 and Turnigy 3XS

laneboysrc/rc-winch-controller
This project is for a winch controller for Radio Controlled cars that uses channel 3 to operate the winch remotely.


Squantor/squantorDevelBoards
Various development boards/test for microcontrollers, check for breakouts here


google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards



It measures 21 × 21 mm and has 2 copper layers, 1.6 mm thick.
23 parts, built around the LPC812M101JDH20. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the laneboysrc/nrf24l01-rc repository on GitHub, at the commit this page was made from: the board is lpc812-nrf24l01-receiver/electronics-8ch/lpc812-nrf24l01-8ch-receiver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).