Skip to the content
2 layers160 × 65 mmPneumatic control unit system, the printed circuit board in 3D

Pneumatic control unit system

kvriet/AirSystem-ESP32-for-Soft-Robotics

An air control system for soft robotics using ESP32

Size
160 × 65 mm
Copper layers
2
Thickness
1.6 mm
Parts
72
Nets
49
Pads
181
Tracks, vias
234, 0
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
13 Jan 2026
Updated
6 Nov 2026

Overview

Pneumatic control unit system is an open-source printed circuit board by kvriet, from the kvriet/AirSystem-ESP32-for-Soft-Robotics repository on GitHub, published under the MIT licence. It is a 2-layer board of 160 × 65 mm with 72 parts on 49 nets, routed with 234 tracks and 0 vias.

It is built around the IRLB8743PBF. Its parts include 19 resistors, 13 diodes, 10 capacitors, 5 switches and 4 transistors. It belongs with the ESP32 and RISC-V boards of this library.

Main components

1

README

README.md

AirSystem for Soft Robotics

Modular Air System for Soft Robotics using ESP32
Designed and created by C.M. van Riet - Jan 2026
With thanks to d.search at Eindhoven University of Technology for their guidance.
Special thanks to Geert van den Boomen for checking the schematics and debugging the circuits.

The system

Example application

AirSystem-ESP32 was designed as a low-cost way to rapidly prototype with air, costing roughly €60 for the entire system. AirSystem consists of 1 controller, 4 pneumatic components (pumps and valves), and 2 pressure sensors. Through a 12V power brick, the board provides 12V power and as such, any pump or solenoid that requires 12V power can be attached to the board.

System overview

Pneumatic Components

For the pneumatic board, easy-to-find components are used:

  1. Pump 370A, 12V, 3.2LPM
  2. Solenoid valve Skoocom SC0829GW, 12V
  3. MCP-H10 pressure sensor, 0-200kPa, 3.3V

Manual

A manual for AirSystem describes in detail how the system works and how the Arduino library can be installed: AirSystem Manual Users are free to connect the sensor, pump, and valve to their inflatables as desired. Example Arduino sketches are provided that work well with the board to control inflatables.

Arduino Library

The system is controlled by a Waveshare ESP32-C3-Zero and can be programmed through the Arduino IDE with a custom library: AirSystem This folder should be unzipped and placed in the libraries folder of the Arduino folder, or imported (zipped) as a library in the Arduino IDE. Select the XIAO_ESP32C3 board to upload sketches to the board.

The library comes with 7 examples that showcase the abilities of AirSystem:

  1. Manual control
  2. Pressure reading
  3. Pump control
  4. Valve control
  5. Pump control without delay
  6. Other configurations
  7. Object arrays

Schematics and KiCAD Files

The schematics for this project and the KiCAD files can be found here: KiCAD folder.

3D Printing Files

The STLs for this project can be found here: Design Files.

  • The prints will fit most regular printers and can be printed out of PLA, 0.3 layer height, 4 perimeters (walls), 20% infill. The cushions for the pumps and solenoids are printed in TPU. These cushions can be replaced with some sponge (simple kitchen sponges work well) if TPU printing is not an option.
  • To minimise vibrations and prevent the cases from sliding around on a hard surface, 6mm silicone feet can be added to the bottom of the base.

The screws needed for these cases are:

  • 4x M3x5 for the PCB
  • 12x M3x10 for the clamps (or 16x M3x10 depending on the configuration)

Limitations

  • The Skoocom solenoid valve is able to remain closed up to pressures of 100kPa, whereas the pump is able to deliver 150kPa. This means the valve will start leaking at pressures over 100kPa. In practice, this is not a major issue, as our projects rarely need pressures of over 100kPa (usually maxing out at 50kPa for haptic purposes). However, this overpressure might reduce valve longevity in the long run. In the future, a higher-pressure solenoid valve could be found, or a pump could be found that delivers max 100kPa. This would also allow for a lower-range pressure sensor to be used, the MCP-H10 0-100kPa, 3.3V. Switching to the 0-100kPa sensor would also double pressure measuring resolution.
  • Currently no PID has been implemented in the library. As many inflatables or the tubing used are somewhat elastic, I have found that setting a target pressure (feedback loop sensor reading to pump power) is enough to achieve that pressure with a minimal offset. However, for more high-end applications, PID should be implemented.
  • The Skoocom solenoid valve is not proportional. It is just open/closed. This means that controller deflation is a challenge. This can be worked around by turning on the pump simultaneously to opening the valve to reduce the air flowing out. Additionally, a resistor (very thin tube) could be connected to the valve outlet to reduce airflow out of the system. However, such a resistor also slows down response times when air does need to evacuate the system quickly. This is a trade-off for how cheap this entire system is.

Parts

72
QtyValueFootprintReferences
101kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2, R3, R4, R6, R7, R10, R11, R16, R17
8100nFCapacitor_THT:C_Rect_L7.2mm_W2.5mm_P5.00mm_FKS2_FKP2_MKS2_MKP2C1, C2, C5, C6, C7, C8, C9, C10
6jumperJumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mmJP1, JP2, JP3, JP4, JP5, JP6
4100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR12, R13, R18, R19
41N4001Diode_THT:D_DO-41_SOD81_P10.16mm_HorizontalD4, D5, D10, D11
41N4148Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD6, D7, D12, D13
4IRLB8743PBFPackage_TO_SOT_THT:TO-220-3_VerticalQ1, Q2, Q3, Q4
4SW_PushButton_Switch_THT:SW_PUSH_6mmSW2, SW3, SW4, SW5
33k3Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR5, R8, R14
2100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC3, C4
21k2Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR9, R15
2LED_BlueLED_THT:LED_D3.0mmD2, D8
2LED_RedLED_THT:LED_D3.0mmD3, D9
2PumpTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalM1, M3
2ValveTerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_HorizontalM2, M4
2~Library:MCP_H10_breakoutU2, U3
1Barrel_JackConnector_BarrelJack:BarrelJack_HorizontalJ4
1ConnConnector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_VerticalJ1
1ConnConnector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_VerticalJ2
1ESP32-C3-ZeroLibrary:ESP32-C3-ZeroU1
1GNDTestPoint:TestPoint_Loop_D2.50mm_Drill1.0mmGND
1LED_GreenLED_THT:LED_D3.0mmD1
1SW_SPSTLibrary:SW_rocker_switch_smallSW1

The 68 most common of 72 parts.

More from kvriet/AirSystem-ESP32-for-Soft-Robotics

1
  • 2 layers19.4 × 9.3 mmPneumatic control unit system, the printed circuit board in 3D

    Pneumatic control unit system

    kvriet/AirSystem-ESP32-for-Soft-Robotics

    An air control system for soft robotics using ESP32

    6 partsMIT

Similar boards

  • 2 layers157.5 × 97.8 mmEsp32PrinterController, the printed circuit board in 3D

    Esp32PrinterController

    MitchBradley/Esp32PrinterController

    PCB design for 3D printer controller using ESP32 processor

    101 parts16MIT
  • 2 layers164 × 126.5 mmDAB converter, the printed circuit board in 3D

    DAB converter

    lbregy/Power-Electronics

    202 parts
  • 2 layers102.8 × 46.5 mmMETAL AIR BMS, the printed circuit board in 3D

    METAL AIR BMS

    MAATHES-THILAK-K/METAL_AIR_BMS

    STM32-based Single Cell Metal-Air Battery Management System (BMS) featuring real-time voltage/current monitoring, temperature sensing, hydrogen gas detection, protection mechanisms, UART communication, and a…

    88 parts
  • 2 layers50 × 90 mmHackholidays, the printed circuit board in 3D

    Hackholidays

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    72 parts915
  • 2 layers59.9 × 82.5 mmCentronics 50Pin, the printed circuit board in 3D

    Centronics 50Pin

    BlueSCSI/BlueSCSI-v2

    BlueSCSI v2/Ultra - an open source, open hardware, SCSI emulator using the Pi Pico PR2040 and Pico 2 RP2350

    72 parts459GPL-3.0
  • 2 layers45.7 × 168.3 mmSPIN RCV PANEL, the printed circuit board in 3D

    SPIN RCV PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    72 parts431
  • 2 layers152.4 × 101.6 mm8088-FE2010A SBC, the printed circuit board in 3D

    8088-FE2010A SBC

    skiselev/micro_8088

    Micro 8088 - IBM XT Compatible Processor Board based on Faraday FE2010 chipset

    72 parts412GPL-3.0
  • 2 layers80.8 × 50.8 mmProbeSenseNumbers, the printed circuit board in 3D

    ProbeSenseNumbers

    Architeuthis-Flux/JumperlessV5

    The next generation jumperless breadboard

    72 parts332

Questions

How big is the Pneumatic control unit system PCB?

It measures 160 × 65 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pneumatic control unit system use?

72 parts, built around the IRLB8743PBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pneumatic control unit system KiCad files?

From the kvriet/AirSystem-ESP32-for-Soft-Robotics repository on GitHub, at the commit this page was made from: the board is KiCAD/Pneumatic control v3/Pneumatic control unit system.kicad_pcb and its schematic KiCAD/MCP breakout/Pneumatic control unit system.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pneumatic control unit system design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).