

Crimps
Mutated Kinks = Karltron Crimps
- Size
- 99 × 128.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 100
- Nets
- 66
- Pads
- 259
- Tracks, vias
- 440, 81
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 18 Nov 2021
- Updated
- 27 Aug 2024
Overview
Crimps is an open-source printed circuit board by kstammits, from the kstammits/crimps repository on GitHub. It is a 2-layer board of 99 × 128.5 mm with 100 parts on 66 nets, routed with 440 tracks and 81 vias.
It is built around the OPA4171AID, TL072 and MMBT3904, with the S1JL and MMBFJ309 among its other parts. Its parts include 32 resistors, 18 connectors, 12 capacitors, 12 diodes and 3 ICs.
Main components
5OPA4171AID
SOIC-14-18V~-1.35V、1.35V~18V -40℃~+125℃ 1.8mV 120dB 14nV/√Hz@1kHz 15pA 2.7V~36V 25mA 2uV/℃ 3MHz 4 475uA 4pA 6V/us ESD protection、EMI filtering/RF suppression Rail-to-rail output SOP-14 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierTL072
SOP-8-18V~18V 0℃~+70℃ 1.4mA 1.5nA 10V/us 10mV 2 2.5nA 3MHz 85dB SOP-8 Operational Amplifier ROHSGcoreOperational AmplifierMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)S1JL
SOD-123FLDiodes - General PurposeJiangsu Changjing Electronics Technology (CJ)MMBFJ309
SOT-23-55℃~+150℃ 1 N-channel 25V 2V 2pF 30mA 350mW N-Channel SOT-23 JFETs ROHSonsemiJFETs
README
crimps/README.mdcrimps
Mutated Kinks = Karltron Crimps
Originally cloning Mutable Instruments' Kinks https://github.com/pichenettes/eurorack Transferring from EAGLE to KiCad and updating from 0402 to 0805 construction means basically the whole thing is rewritten from scratch. The PCB is therefore unrelated to Kinks: Crimps is a karltron design 2021.
Info on karltron.com/crimps
it's cc-by-sa so copyleft
On the internet forums, someone else has mentioned started a THT version, asking about it but not shared yet because reasons. https://modwiggler.com/forum/viewtopic.php?p=3644155
signal diode: FDLL4148 is D1206
changing pinout on transistors, to SOT-23. so DO BE CAREFUL AND RECHECK THE PINOUT (note v101 has the transistors on upside down, v122 is fixed)
layout looking fine in 0805
The S&H calls for a fancy C0G capacitor and OPA4171 opamp. We'll try it with a plain capacitor and TL074, which are compatible, but expect poor performance. I'm curious how poor, if it's acceptable we can save $$. Will try both, and report back here. But v101 is otherwise broken so
when the input looks like noise at >9vpp, which is normal, the trigger goes off for successivly lower notes. feels like an accumulating towards -7.5Volts. Input values lower than -7V till self trigger If something softer is in the input, or values <7 volts absolute it will not self-trigger. i think i need to add a capacitor somewhere or redo the ground plane. Anytime the input sinks below -7V it pulls on the gate. Not sure it's really triggering, would need a two-channel scope to see if they coincide.
if you keep the input above -7V, then the vgs doesn't trigger and everything is good. So I should just reduce the noise volume, the original kinks was showing just about +/-5V, and 10vpp is enough noise. mine's doing like 19vpp noise, and catching a very brief acquisition during noise spikes under -7V.
so actually it works fine. i should/need/to/ reduce the noise volume to 10vpp to avoid the -7V issue. That's fixed by changing R27 from a 1.5M as originally given to a 1M. Now the noise is only +/-6V and everything works. then of course flip the transistors right-side-up. I've tested with only a J112 THT jfet tacked on crooked.
Testing another JFET as replacement; the MMBFJ201 (marked 6P) is not great. Sort of works, sort of doesnt. The trigger time is not sufficient for acquisition, so each trigger can only move the sample by a few volts, and swinging +/-10V will need 2,3,4,5 triggers. Also, when the input is quite low the sample drains without triggers, so the J201 seems to have some leakage Igs as well as a higher Rds-on vs the J112. The incomplete-acquisitions problem might be okay for your use, but it really reduces the output range when the internal noise source is +/-6V and each trigger seems to only change the value to +/-1V.
Testing the MMBF4392 (marked 6K) Holds nicely down to -7.5V then drops, as others do, because my gate off voltage is -11, so less than four difference causes a sampling. Seems to be working well.
Testing the MMBFJ112 (marked 6R) last since a THT J112 was working well. Also seems to perform adequately.
During hold testing, discovered unplugging and replugging the output causes a drop in the sample; perhaps this is caused by the brief short to ground pulling on the opamp. Additional decoupling caps did not help, looks like the OPA4171 final out buffer loses some state through the 180R output. Another output stage might be required to separate the held voltage from the output buffer. That's not fixable without additional chips.
Parts
100| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | PJ301_THONKICONN6 | k2:WQP_PJ_301M6 | J1, J2, J3, J4, J5, J6, J7, J8, J9, J10, J11, J12 |
| 10 | 1N4148 | Diode_SMD:D_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D3, D4, D5, D6, D7, D8, D9, D10, D11, D12 |
| 9 | J1 | MountingHole:MountingHole_6.4mm_M6_Pad | H2, H2, H2, H2, H2, H2, H2, H2, H2 |
| 7 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R14, R16, R17, R18, R28, R32 |
| 7 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5, C6, C7, C8, C9, C11 |
| 7 | 180 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R8 |
| 6 | 200k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R9, R10, R11, R12, R13, R15 |
| 4 | 220k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19, R20, R21, R22 |
| 3 | 1.0M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R24, R26, R29 |
| 3 | Conn_01x05_Female | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J13, J14, J15 |
| 3 | Conn_01x05_Male | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J16, J17, J18 |
| 3 | J2 | MountingHole:MountingHole_6.4mm_M6_Pad | H6, H6, H6 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R25 |
| 2 | 22u | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1, C2 |
| 2 | LOGO | Symbol:snail4.sm | G***, G*** |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q2, Q3 |
| 2 | MountingHole_Pad | MountingHole:SLOT-1 | H1, H14 |
| 2 | S1JL | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2 |
| 1 | 100p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C12 |
| 1 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R31 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10 |
| 1 | 470K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R27 |
| 1 | 470k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R30 |
| 1 | Logo_Open_Hardware_Small | Symbol:snail4.sm | G1 |
| 1 | M05X2PTH | k2:AVR_ICSP | JP1 |
| 1 | MMBFJ309 | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q1 |
| 1 | OPA4171 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | IC3 |
| 1 | TL072 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | IC2 |
| 1 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | IC1 |
The 98 most common of 100 parts.
Similar boards
- 2 layers19 × 108.4 mm

- 2 layers85 × 56 mm

- 4 layers16.2 × 23.2 mm

AART11
ImbaNagibator/slot-car-ecom
This repo contains a KiCad design, documentation and ancillary artifacts for a slot car brushless motor electronic commutator or "eCom", also known as an Electronic Speed Controller (ESC).
82 partsCC0-1.0 - 2 layers88.9 × 106 mm

- 4 layers202.5 × 110 mm

- 4 layers80 × 108 mm

Bmcv
Bemeier/bmcv
Macro CV controller for eurorack inspired by the Emblematic Systems Catalyst
373 parts7CC-BY-SA-4.0 - 2 layers57.3 × 105 mm

- 4 layers102 × 108 mm

Rools core
amorwilliams/Rools
10HP Eurorack 多功能可视化 DSP 模块 · Daisy Seed 固件 · 横屏频谱/示波/效果器单 App 平台
148 parts
Questions
How big is the Crimps PCB?
It measures 99 × 128.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Crimps use?
100 parts, built around the OPA4171AID, TL072, MMBT3904 and S1JL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Crimps KiCad files?
From the kstammits/crimps repository on GitHub, at the commit this page was made from: the board is crimps/k2.kicad_pcb and its schematic Jinx/Jinx.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Crimps design in my own project?
Its repository states no licence, so its author keeps all rights: ask kstammits before reusing the design.