Skip to the content
2 layers57.5 × 40 mmNot a block, the printed circuit board in 3D

Note Block from Minecraft but in real life,

Size
57.5 × 40 mm
Copper layers
2
Thickness
1.6 mm
Parts
19
Nets
20
Pads
55
Tracks, vias
84, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
19 Oct 2026
Updated
25 Oct 2026

Overview

Not a block is an open-source printed circuit board by kryo-77, from the kryo-77/not-a-block repository on GitHub. It is a 2-layer board of 57.5 × 40 mm with 19 parts on 20 nets, routed with 84 tracks and 0 vias.

It is built around the BZX55C3V3. Its parts include 6 connectors, 4 resistors, 3 diodes, 1 capacitor and 1 IC. It belongs with the ESP32 and RISC-V boards of this library.

Main components

1

README

README.md

Not-a-block

Note block from Minecraft but in real life.

Note block isometric image

Note block and instrument block stacked image

What it is:

I made a note block from Minecraft which functions close enough to the actual game. You can tap the top face of the note block to play it and hit the back side of it to change the pitch (like right-clicking in Minecraft).

You can change the sound of the note block by placing it on different types of blocks as well. This is possible as there is an RFID card reader underneath the note block and a RFID tag on top of the instrument block (like stone, glass, sand, etc.)

How it works:

The note block contains an ESP-32-C3-SuperMini. It's the microcontroller which connects to different components. It also stores music files inside its flash memory. As the music files are under a second, we can store quite a lot of them inside the ESP32, so there is no need for a SD card module (which also saves pins). Sound is played by a MAX98357A I2S amp with a 4Ω 3W speaker (50mm diameter).

There are 2 piezoelectric sensors present inside the note block's top and back surface. When you hit the surface, the piezo sends voltage to the ESP32's data pin which tells it to play the sound.

Note block piezo mount

There are 16 different instrument sounds which the note block can play, which depend on the block below it. When the top surface is hit, it only tells ESP32 to play a single sound each time. When the back surface is hit, which is for changing the pitch of the instrument, each hit changes the sound to a different pitch. We don't need to have different audio inside the ESP32 for each pitch, as it can directly change on its own. Only the instrument sounds are needed to be stored.

For detecting which block is present below the note block, a PN532 RFID card reader sits on the bottom surface, while a RFID tag sits on the top surface of the other blocks. The tag gets read every few seconds so that if the block changes, its sound changes as well without a lot of delay. 4 magnets are also present under the note block's surface as well as an instrument block's top surface, so that lining up the tags as well as the blocks is very easy. The magnets are also in different polarities (NN/SS) on the surfaces so you don't accidentally misplace back of the note block (where you hit to change pitch).

Note block RFID mount

Note block pcb mount

The front surface of the note block contains holes so that the speaker can output sound. I decided to only make holes in the black layer as it is thinner than the white one and would not show that many holes as well.

Note block speaker grill

Dimensions:

  1. Note block / Instrument block: 10 x 10 x 10 cm
  • Each face has 3 layers, overall 0.4cm thick.
  1. Note block PCB: 5.75 x 4 cm
  2. Piezoelectric sensor: 3.5cm diameter

Files:

  • CAD folder contains .f3d (fusion) file & .stl for printing.
  • PCB folder contains kicad files, export.zip has gerber files, 3d_model has .step file of PCB. It has a footprints_ext folder which contains footprint for ESP32-C3-SuperMini which I downloaded online.
  • CODE folder contains basic test code (when RFID card gets detected, a beep is produced) which uses a XIAO s3, MFRC522 RFID reader and no piezo sensor. I only had these components with me so code are based on it instead of the BOM.

How to assemble / Details about the 3d printed parts (!!WIP!!)

Parts laid out

There are two types of block: Note block and Instrument block. Note block contains the electronics while the instrument block only contains a single RFID tag + 4 magnets on its top surface.

There are 6 parts per block. Final assembly should measure 10x10x10cm.

The faces are different sizes as all need to fit together to form the 10x10x10cm. It is pretty easy to assemble as same dimension face are opposites of each other.

Each face has a rectangular hole on its bottom surface and a rectangle sticking out on its top surface. The hole attaches to the base plate, while the rectangle goes in the top plate

Thats it for the assembly, just pushing the faces on to the base, no need for screws. Though the design might get changed depending on it actually works irl as I cant test the prints myself.

desc

Screws aren't really needed other than mounting the pcb, that too is optional as I've made standoffs on the base plate.

PCB schematic / render

PCB schematic

PCB render

BOM

NoComponentQtyUnit Price (USD)UsesLink
1ESP32-C3 SuperMini12.72MCUhttps://makerbazar.in/products/esp32-c3-supermini-iot-development-board
2PN532 RFID/NFC V3 module12.83RFID readerhttps://robocraze.com/products/nfc-near-field-communication-rf-id-v3-module
3MAX98357A I2S amplifier12.04Sound amplifierhttps://robu.in/product/smartelex-i2s-audio-breakout-max98357a/
4Speaker, 4 ohm 3W11.05Sound outputLocal shop
535mm piezo sensor20.23Hit and pitch sensinghttps://robocraze.com/products/35mm-piezo-sensor
6BZX55C3V3 zener diode20.02Piezo protectionhttps://robu.in/product/bzx55c3v3-1-2w-zener-diode-pack-of-40/
74.7k resistor2n/aPiezo protection
8470uF polarised capacitor1n/aPower smoothing
91N5819 Schottky diode10.06Power protection (USB and battery connected together)https://robu.in/product/1n5819-ap-mcc-40v-1a-600mv1a-do-41-schottky-diodes-rohs/
103d print114.553d print(printing legion channel - slack) https://print.speedhawks.online/slice
11PCB19.48PCB manufacturinghttps://robu.in/product/online-pcb-manufacturing-service/

Parts

19
QtyValueFootprintReferences
4, , ,
21MResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR1, R4
24.7kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR2, R3
2BZX55C3V3Diode_THT:D_DO-41_SOD81_P2.54mm_Vertical_AnodeUpD2, D3
11N5819Diode_THT:D_DO-41_SOD81_P2.54mm_Vertical_AnodeUpD1
1470uFCapacitor_THT:CP_Radial_D8.0mm_P3.50mmC1
15v extTerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mmJ6
1ESP32-C3_SUPERMINI_THMODULE_ESP32-C3_SUPERMINI_TH:MODULE_ESP32-C3_SUPERMINI_THU1
1JumperConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ5
1MAX98357AConnector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ2
1RFID readerConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1
1[HIT] PiezoConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1[Pitch] PiezoConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ4

Similar boards

  • 2 layers80 × 60 mmSatelliteNode, the printed circuit board in 3D

    SatelliteNode

    tokai-student-rocket-project/Gen6-GSE-Elec

    第6世代自動GSE電装系

    34 parts2MIT
  • 2 layers43.9 × 27.7 mmTcd1304-4v, the printed circuit board in 3D

    Tcd1304-4v

    OpnTec/open-spectrometer-hardware

    Open source VIS spectrometer

    19 parts1.5k
  • 2 layers50 × 60 mmDebate Device, the printed circuit board in 3D

    Debate Device

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    19 parts915
  • 2 layers102.9 × 96.7 mmISA adapter, the printed circuit board in 3D

    ISA adapter

    polpo/picogus

    Emulation of ISA sound cards and CD-ROM on Raspberry Pi Pico (GUS, SB/Adlib, MPU-401, Tandy, CMS, Panasonic CD-ROM) with USB mouse/joystick support

    19 parts805
  • 2 layers60 × 39 mmPs2usb, the printed circuit board in 3D

    Ps2usb

    rasteri/HIDman

    Adapting USB devices to work on old computers

    19 parts432
  • 2 layers70.1 × 43.2 mmIaq device, the printed circuit board in 3D

    Iaq device

    nkitanov/iaq_board

    IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

    19 parts396
  • 2 layers80 × 80 mmGB BRK CPU G1, the printed circuit board in 3D

    GB BRK CPU G1

    Gekkio/gb-hardware

    Game Boy -related custom hardware by gekkio

    19 parts379CC-BY-4.0
  • 2 layers25.4 × 25.4 mmIna169, the printed circuit board in 3D

    Ina169

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    19 parts282

Questions

How big is the Not a block PCB?

It measures 57.5 × 40 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Not a block use?

19 parts, built around the BZX55C3V3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Not a block KiCad files?

From the kryo-77/not-a-block repository on GitHub, at the commit this page was made from: the board is PCB/notablock.kicad_pcb and its schematic PCB/notablock.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Not a block design in my own project?

Its repository states no licence, so its author keeps all rights: ask kryo-77 before reusing the design.