Skip to the content
2 layers147.4 × 112.6 mmMain pcb, the printed circuit board in 3D

Custom low-profile mechanical split keyboard largely inspired by Corne v3.

Size
147.4 × 112.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
81
Nets
97
Pads
801
Tracks, vias
2,598, 292
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Nov 2025
Updated
26 Apr 2026

Overview

Main pcb is an open-source printed circuit board by krlberg, from the krlberg/hormesis-keyboard repository on GitHub, published under the MIT licence. It is a 2-layer board of 147.4 × 112.6 mm with 81 parts on 97 nets, routed with 2,598 tracks and 292 vias.

Its parts include 50 diodes and 26 switches. It belongs with the keyboards and input boards of this library.

README

README.md

Hormesis Keyboard

A custom low-profile wireless split mechanical keyboard, inspired by the Corne v3.


Overview

SpecDetail
Keys50 (split 25/25)
Layout5×6 column stagger per half + 3-key thumb cluster
ProfileLow-profile
WirelessBluetooth 5.0, up to 5 device profiles
Controllernice!nano v2 (nRF52840)
RGBWS2812 underglow, 25 LEDs per half

Repository Structure

text
hardware/
├── kicad/          KiCAD PCB schematic and layout
├── footprints/     Ergogen custom footprints
├── output/         Generated outputs (gerbers, outlines, cases)
├── top_plate/      Top plate Ergogen design
├── firmware/       Pre-built .uf2 files ready to flash
└── config.yaml     Ergogen PCB config

boards/             ZMK shield definition (hormesis_left / hormesis_right)
config/             ZMK keymap and firmware config
zephyr/             ZMK module config
build.yaml          ZMK GitHub Actions build targets
.github/workflows/  Auto-build firmware on push

Layout

text
  1   2   3   4   5                   6   7   8   9   0
TAB   Q   W   E   R   T       Y   U   I   O   P  ESC
CAP   A   S   D   F   G       H   J   K   L   ;  SFT
  Z   X   C   V   B                   N   M   ,   .   /
                CTL ALT GUI     SPC  FN BSP

Fn Layer (hold FN)

text
 F1  F2  F3  F4  F5                  F6  F7  F8  F9 F10
  `   !   @   #   $   %       ^   &   *   (   )  DEL
  _   _   -   =   [   ]      LFT DWN  UP RGT   '  ENT
BTC BT0 BT1 BT2 BT3             BT4 RGB  H+  S+   \
            USB BLE TOG     BRI EFF BOT

BTC = clear BT, BT0–4 = select profile, RGB = toggle underglow, H+/S+ = hue/saturation, BRI = brightness, EFF = next effect, BOT = bootloader, USB/BLE/TOG = output source.


Flashing Firmware

Pre-built .uf2 files are in hardware/firmware/:

text
hardware/firmware/hormesis_left-nice_nano_v2.uf2
hardware/firmware/hormesis_right-nice_nano_v2.uf2
  1. Double-tap the reset button on the nice!nano — it mounts as a USB drive (NICENANO).
  2. Drag the matching .uf2 file onto the drive.
  3. Flash left first, then right.

Customizing Keymaps

Edit the keymap in config/hormesis.keymap, push to GitHub, and the Actions workflow auto-builds new firmware. Download from the Actions tab.

ZMK Studio (GUI, no recompile): Add CONFIG_ZMK_STUDIO=y to config/hormesis.conf, rebuild, flash, then use zmk.studio to remap keys live over USB or BLE.


Bill of Materials

PartQty
nice!nano v22
Low-profile MX switches50
Low-profile keycaps50
WS2812B LEDs50 (25 per half)
SOD-123 diodes50
JST PH 2.0 battery connector2
LiPo battery (301230 or similar)2
Reset switch (3×6mm SPST)2

PCB Fabrication

Gerbers are in hardware/kicad/gerber/. Recommended fab settings:

  • Layers: 2
  • Thickness: 1.6 mm
  • Surface finish: HASL or ENIG
  • Quantity: 5 (gives 2 full keyboards + spares)

License

MIT

Parts

81
QtyValueFootprintReferences
25ComboDiodeD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +9
25PG1350S1, S2, S10, S11, S12, S13, S14, S15, S16, S17, S18, S19, S20, S21, S22, S23 +9
25WS2812BLED1, LED2, LED10, LED11, LED12, LED13, LED14, LED15, LED16, LED17, LED18, LED19, LED20, LED21, LED22, LED23 +9
2JST_PH_S2B-PH-K_02x2.00mm_AngledJST1, JST2
2Panasonic_EVQPUL_EVQPUCPanasonic_EVQPUL_EVQPUCB1, B2
1ceoloide:mcu_supermini_nrf52840MCU1
1power_switchSW1

Similar boards

  • 2 layers162.9 × 178.9 mmAMPCD, the printed circuit board in 3D

    AMPCD

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    81 parts431
  • 2 layers177.2 × 114.3 mm8-Bit CPU 32k, the printed circuit board in 3D

    8-Bit CPU 32k

    slu4coder/Minimal-UART-Computer-1-2

    Legacy: Version 1 and 2 of my TTL-only CPU featuring UART I/O, an expansion port, 512KB SSD at up to 10MHz clock speed

    81 parts184
  • 2 layersEdrumulus, the printed circuit board in 3D

    Edrumulus

    corrados/edrumulus

    Open Source E-Drum Trigger Module

    81 parts163GPL-2.0
  • 2 layers64 × 55 mmZynthiandac bk2, the printed circuit board in 3D

    Zynthiandac bk2

    zynthian/zynthian-hw

    Zynthian hardware stuff: PCBs, schemes, parts specifications, pin assignment, ...

    81 parts156
  • 2 layersBD0027, the printed circuit board in 3D

    BD0027

    schlae/VapeRE

    Reverse engineered disposable v a p e boards

    81 parts136
  • 2 layers41.9 × 62.8 mmColumn, the printed circuit board in 3D

    Column

    AlaaSaadAbdo/Rommana

    A 30 key well powered by Xiao BLE

    81 parts105
  • 2 layers38.6 × 38.6 mmIotLedDriver, the printed circuit board in 3D

    IotLedDriver

    BerkeleyHCI/PolymorphicBlocks

    A Python-based hardware description language for PCBs for higher-level (block-diagram / system-architecture level) PCB design through libraries of directly reusable subcircuit generators.

    81 parts94BSD-3-Clause
  • 2 layers98.5 × 45.4 mmIdawgz32, the printed circuit board in 3D

    Idawgz32

    ChrisChrisLoLo/idawgz32

    A full 32 key mechanical keyboard that can be made for only $5

    81 parts77GPL-3.0

Questions

How big is the Main pcb PCB?

It measures 147.4 × 112.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Main pcb use?

81 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Main pcb KiCad files?

From the krlberg/hormesis-keyboard repository on GitHub, at the commit this page was made from: the board is hardware/kicad/main_pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Main pcb design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).