

Kabot2
Mine projects
- Size
- 132 × 68 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 82
- Nets
- 114
- Pads
- 372
- Tracks, vias
- 446, 15
- Pours
- 25
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 22 Sep 2016
- Updated
- 22 Sep 2016
Overview
Kabot2 is an open-source printed circuit board by kpochwala, from the kpochwala/KiCad-projects repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 132 × 68 mm with 82 parts on 114 nets, routed with 446 tracks and 15 vias.
It is built around the MC33932EK, LTC4316CDD and LM1117-3.3, with the LM1117-5.0 and TSHF6210 among its other parts. Its parts include 28 capacitors, 17 resistors, 15 ICs, 14 diodes and 4 connectors. It belongs with the STM32 boards of this library.
Main components
5MC33932EK
SOIC-54-EP-300mil-40℃~+125℃ 2 470mΩ 5A 5V~28V Bipolar Driver Yes SOIC-54-EP-300mil Stepper Motor Driver ROHSNXP SemiconductorsStepper Motor DriverLTC4316CDD
DFN10Single I2C/SMBus Address TranslatorAnalog DevicesUncategorisedLM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedLM1117-5.0
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 5V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedTSHF6210
插件-40℃~+85℃ 1.5V 100mA 170mW 327mW/sr 40nm 5V 890nm 8° 插件 Infrared LED Emitters ROHSVishay IntertechnologyInfrared LED Emitters
README
README.mdKiCad-projects
Mine projects
Parts
82| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nF | Capacitors_SMD:C_0603_HandSoldering | C1, C2, C3, C4, C5, C7, C9, C11, C13, C14, C17, C18, C19, C20 |
| 9 | 4k7 | Resistors_SMD:R_0603_HandSoldering | R1, R2, R3, R4, R5, R6, R7, R8, R9 |
| 8 | TSHF6210 | libraries:TSHF6210_Reverse | D1, D2, D3, D4, D5, D6, D7, D8 |
| 6 | 10uF | Capacitors_Tantalum_SMD:TantalC_SizeA_EIA-3216_HandSoldering | C23, C23, C24, C24, C26, C26 |
| 6 | 1K | Resistors_SMD:R_0603_HandSoldering | R12, R12, R13, R13, R14, R14 |
| 4 | 1uF | Capacitors_SMD:C_1206_HandSoldering | C6, C8, C10, C12 |
| 4 | LTC4316 | Housings_SSOP:MSOP-10_3x3mm_Pitch0.5mm | U2, U4, U6, U8 |
| 4 | POT | Potentiometers:Potentiometer_Bourns_3296X_3-8Zoll_Inline_ScrewFront | RV1, RV2, RV3, RV4 |
| 4 | VCNL3020 | libraries:VCNL3020_footprint | U3, U5, U7, U9 |
| 2 | 100uF | Capacitors_Tantalum_SMD:TantalC_SizeC_EIA-6032_HandSoldering | C21, C22 |
| 2 | 220R | Resistors_SMD:R_0603_HandSoldering | R10, R11 |
| 2 | B | LEDs:LED_0603 | D11, D11 |
| 2 | G | LEDs:LED_0603 | D10, D10 |
| 2 | IE2-512 | Pin_Headers:Pin_Header_Straight_1x06 | P2, P3 |
| 2 | LM1117-3.3 | warsztaty:LM1117_SOT223 | U13, U13 |
| 2 | LM1117-5 | warsztaty:LM1117_SOT223 | U12, U12 |
| 2 | R | LEDs:LED_0603 | D9, D9 |
| 1 | 10nF | Capacitors_SMD:C_0603_HandSoldering | C16 |
| 1 | 10uF | Capacitors_SMD:C_1206_HandSoldering | C15 |
| 1 | CONN_01X03 | Pin_Headers:Pin_Header_Straight_1x03 | P1 |
| 1 | LSM330TR | libraries:LGA24 | U10 |
| 1 | MC33932 | libraries:HSOP_44 | U11 |
| 1 | STM32F030C6Tx | Housings_QFP:LQFP-48_7x7mm_Pitch0.5mm | U1 |
| 1 | SWD | Pin_Headers:Pin_Header_Straight_1x04 | P4 |
More from kpochwala/KiCad-projects
9- 2 layers96 × 78.7 mm

- 2 layers34 × 149.9 mm

- 2 layers

- 2 layers48 × 54 mm

- 2 layers34 × 62 mm

- 2 layers92 × 46 mm

- 2 layers37 × 18.5 mm

- 2 layers90 × 25 mm

- 2 layers40 × 20 mm

Similar boards
- 2 layers11 × 36 mm

- 2 layers84.3 × 58.4 mm

EnocderDriver
NikodemBartnik/Small-Projects
All of smaller projects (Arduino, PCBs, electronics, code)
35 parts55 - 2 layers97 × 97 mm

QO100 RX
barisdinc/N3B_SDR_Transceiver_HW
V/U/SHF and QO-100 SDR Transceiver Project
167 parts20GPL-3.0 - 2 layers85 × 60 mm

BaseModule
KarlVaello/VehicleControlSystem
Vehicle Control System. Using C++ Qt and C. Hardware and Software
67 parts14GPL-3.0 - 2 layers40 × 100 mm

MidiMonger components
dchwebb/MidiMonger
Eurorack MIDI interface supporting USB and serial MIDI. Based on ARM STM32F446 MCU.
70 parts12 - 2 layers96 × 100 mm

- 4 layers80.8 × 100 mm

- 2 layers37 × 90 mm

Questions
How big is the Kabot2 PCB?
It measures 132 × 68 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Kabot2 use?
82 parts, built around the MC33932EK, LTC4316CDD, LM1117-3.3 and LM1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Kabot2 KiCad files?
From the kpochwala/KiCad-projects repository on GitHub, at the commit this page was made from: the board is kabot/kabot2/kabot2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Kabot2 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).