Skip to the content
2 layers15 × 10.8 mmPos rev4 small, the printed circuit board in 3D

Schematic, PCB, and guide for making your own Power-over-Skin receivers (UIST24)

Size
15 × 10.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
16
Pads
72
Tracks, vias
147, 12
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
12 Jul 2024
Updated
23 May 2025

Overview

Pos rev4 small is an open-source printed circuit board by kongmunist, from the kongmunist/Power-Over-Skin-Hardware repository on GitHub. It is a 2-layer board of 15 × 10.8 mm with 27 parts on 16 nets, routed with 147 tracks and 12 vias.

It is built around the SMS7630-005LF. Its parts include 9 capacitors, 7 resistors, 5 connectors, 3 inductors and 1 IC.

Main components

1

README

README.md

Hi, welcome to the Power-over-Skin Repo

This repository contains the PCB files for the receiver board from the ACM UIST paper "Power-over-Skin: Full-Body Wearables Powered By Intra-Body RF Energy"

BOM for receiver

You can assume all parts are generic unless mentioned below:

  • R1-R7: Voltage setting resistors, should be 1% or better

  • L2, L3: buck/boost inductors for the BQ25570. Should handle >200mA saturation current according to BQ25570 datasheet, but we're using low currents so you would probably get away with lower values. We used CB2518T100K and BRC2518T220K

  • C4: Anything >100uF will do. I'm using the F950J107MPAAQ2, it is the only one that's quite so small, but it's also very DC-leaky

  • L1: Should have a self-resonant frequency over 200 MHz in order to accomodate incoming square wave harmonics.

  • C9: Should be NP0, with a Vmax 10V or better

Transmitter

In our experiments, we used a benchtop transmitter and a wearable one to generate 40 MHz square waves. These were passed through an impedance-matching network to couple into the body. The values we used were: first 20pF in series, then 820nH to ground.

The 20pF should be NP0 with a voltage rating higher than the 40MHz you're sending into it. We used this inductor (L-15FR82JV4E) but anything with a self-resonant frequency >200 MHz should work.

tximn.png

Matching for other frequencies

The RF component values are all tuned for 40 MHz and human skin impedance — if you'd like to use another frequency, you'll have to resimulate the circuit.

Further questions?

Feel free to email Andy with any questions!

Parts

27
QtyValueFootprintReferences
5Conn_01x01_PinTestPoint:TestPoint_Pad_D1.0mmJ1, J2, J3, J4, J5
410nFCapacitor_SMD:C_0402_1005MetricC2, C3, C5, C8
34.3MΩResistor_SMD:R_0402_1005MetricR4, R5, R7
24.7uFCapacitor_SMD:C_0402_1005MetricC1, C6
26.8MΩResistor_SMD:R_0402_1005MetricR3, R6
11.8uHInductor_SMD:L_0805_2012MetricL1
1100uFCapacitor_SMD:C_0805_2012MetricC4
110uHInductor_SMD:L_0805_2012MetricL3
11MΩResistor_SMD:R_0402_1005MetricR1
122uFCapacitor_SMD:C_0603_1608MetricC7
122uHInductor_SMD:L_1008_2520MetricL2
15pFCapacitor_SMD:C_0402_1005MetricC9
17.5MΩResistor_SMD:R_0402_1005MetricR2
1BQ25570Package_DFN_QFN:QFN-20-1EP_3.5x3.5mm_P0.5mm_EP2x2mmU1
1MountingHole_PadTestPoint:TestPoint_Pad_D1.0mmH1
1SMS7630-005LFSMS7621-005LF:SOT-23_SKYCR1

Similar boards

  • 2 layers47.6 × 27.3 mmMmc usb 1, the printed circuit board in 3D

    Mmc usb 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    27 parts1.2k
  • 2 layers77.4 × 77.4 mmCORAZON LEDS CON FADE, the printed circuit board in 3D

    CORAZON LEDS CON FADE

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    27 parts915
  • 2 layers44.2 × 29.3 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    27 parts454
  • 2 layers22 × 42 mmNvme bm to e, the printed circuit board in 3D

    Nvme bm to e

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    27 parts253GPL-3.0
  • 2 layers80 × 61 mmPicoProducer, the printed circuit board in 3D

    PicoProducer

    pjgpetecodes/pico-streamdeck

    This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.

    27 parts230MIT
  • 2 layers186 × 45 mmAddOnD, the printed circuit board in 3D

    AddOnD

    freeDSP/freeDSP-aurora

    freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth

    27 parts226CC-BY-SA-4.0
  • 2 layers29.6 × 40.6 mmDbwifi revB, the printed circuit board in 3D

    Dbwifi revB

    ugcs/ddc

    Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.

    27 parts223

Questions

How big is the Pos rev4 small PCB?

It measures 15 × 10.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pos rev4 small use?

27 parts, built around the SMS7630-005LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pos rev4 small KiCad files?

From the kongmunist/Power-Over-Skin-Hardware repository on GitHub, at the commit this page was made from: the board is pos_rev4_small.kicad_pcb and its schematic pos_rev4_small.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pos rev4 small design in my own project?

Its repository states no licence, so its author keeps all rights: ask kongmunist before reusing the design.