Skip to the content
2 layers139 × 154 mm514 display, the printed circuit board in 3D

Sonic Flow senses the music around and visualize the waveform. The sensing device is responsible for detecting the music around.

Size
139 × 154 mm
Copper layers
2
Thickness
1.6 mm
Parts
13
Nets
18
Pads
64
Tracks, vias
187, 25
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
17 Jan 2025
Updated
12 Mar 2025

Overview

514 display is an open-source printed circuit board by knovvX, from the knovvX/TECHIN514_Project repository on GitHub. It is a 2-layer board of 139 × 154 mm with 13 parts on 18 nets, routed with 187 tracks and 25 vias.

Its parts include 3 resistors, 2 diodes, 2 switches and 1 IC. It belongs with the lEDs and displays boards and the ESP32 boards of this library.

README

README.md

TECHIN514_Project

Diyun Lu 2430741

Sonic Flow - A Music Visualization Device

Overview

Sonic Flow senses the music around and visualize the waveform. The sensing device is responsible for detecting the music around. And the display device will display the corresponding waveforms together with a part acting as a monotrome to display the bpm.

IMG_2700

Sensing Device

The sensing device is equipped with a microphone sensor, which is recording the sound waves and send it to display device. A bluetooth module of esp32 will handle this transmission, since in the application, these two devices should not be very far, so I chose bluetooth. Also the sound level will affect the brightness of the LED strip around the cube, louder the sound is, brighter the LED is.

sensing

Display Device

The display device is mainly displaying the waveform and the bpm of the music detected. BPM is displayed through the stepper-motor-driven gauge needle as a monotrome. Further ML will be embedded on the microncontroller to detect the emotion of the music and also display it on the OLED. A design of different kinds of waveforms will be enabled by a button to switch between different designs.

display

Connection Diagram

The connection of the two parts are shown below. They connect with each other through ESP32's Bluetooth module. And ESP32 is responsible for the control of other sensors.

diagram

Device Composition
DeviceSensor / ElementFunctionality
SensingSPH0645LM4H-BMicrophone
Sensing3.7V / ++?Battery
Display3.7V / ++?Battery
DisplaySSD1305(Long, for waves),https://www.adafruit.com/product/292,Adafruit OLED FeatherWing(Small, for displaying bpm)OLED
DisplayD6R90 F2 LFSButton
Display/SensingRGBLED
Displayhttps://www.adafruit.com/product/2424Stepper-motor-driven Gauge Needle
ESP32Bluetooth and control

Parts

13
QtyValueFootprintReferences
3RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3
3SSD1306ssd1306:128x64OLEDBrd1, Brd2, Brd3
2LEDLED_THT:LED_D5.0mmD1, D2
1Battery_CellConnector_JST:JST_JWPF_B02B-JWPF-SK-R_1x02_P2.00mm_VerticalBT1
1SW_SPDTConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalSW2
1SW_SPSTButton_Switch_THT:SW_PUSH-12mmSW3
1Stepper_Motor_bipolarx27:x27_stepper_two_holesM1
1XIAO-ESP32-S3-DIPSeeed Studio XIAO Series Library:XIAO-ESP32S3-DIPU1

More from knovvX/TECHIN514_Project

1
  • 2 layers60.5 × 52 mm514 pcb, the printed circuit board in 3D

    514 pcb

    knovvX/TECHIN514_Project

    Sonic Flow senses the music around and visualize the waveform. The sensing device is responsible for detecting the music around.

    7 parts

Similar boards

  • 2 layers40 × 20 mmUsb uart, the printed circuit board in 3D

    Usb uart

    earthtojake/text-to-cad

    Design physical products with AI

    13 parts26kMIT
  • 2 layers35 × 29 mmMagSpoofTC, the printed circuit board in 3D

    MagSpoofTC

    samyk/magspoof

    A portable device that can spoof/emulate any magnetic stripe, credit card or hotel card "wirelessly", even on standard magstripe (non-NFC/RFID) readers.

    13 parts4.2k
  • 2 layers20.6 × 23.6 mmAO-03 signal amplifier, the printed circuit board in 3D

    AO-03 signal amplifier

    fossasia/pslab-scripts

    Pocket Science Lab - Scripts for Sensor Experiments

    13 parts1.6kApache-2.0
  • 2 layers47 × 35.6 mmMX7-C-35PL C11, the printed circuit board in 3D

    MX7-C-35PL C11

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    13 parts1.2k
  • 2 layers95 × 95 mmCube batteryboard, the printed circuit board in 3D

    Cube batteryboard

    willem-pennings/balancing-cube

    A cube that balances itself in a corner or edge using reaction wheels

    13 parts1.1kGPL-3.0
  • 2 layers15.2 × 20.3 mmPt100stick, the printed circuit board in 3D

    Pt100stick

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    13 parts1.1kGPL-3.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    13 parts1kGPL-3.0

Questions

How big is the 514 display PCB?

It measures 139 × 154 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 514 display use?

13 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 514 display KiCad files?

From the knovvX/TECHIN514_Project repository on GitHub, at the commit this page was made from: the board is 514_display/514_display.kicad_pcb and its schematic 514_display/514_display.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the 514 display design in my own project?

Its repository states no licence, so its author keeps all rights: ask knovvX before reusing the design.