knielsen/pcb_esp_displayPCB for labitat small displays and ESP8266
Pcb esp is an open-source printed circuit board by knielsen, from the knielsen/pcb_esp_display repository on GitHub. It is a 2-layer board of 90 × 62 mm with 32 parts on 60 nets, routed with 485 tracks and 52 vias.
It is built around the ESP-12E and S8050. Its parts include 14 resistors, 4 capacitors, 3 ICs, 3 connectors and 2 transistors. It belongs with the ESP8266 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10k | Resistors_SMD:R_0805_HandSoldering | R2, R3, R4, R5, R6, R7, R9 |
| 5 | 220 | Resistors_SMD:R_1206_HandSoldering | R10, R11, R12, R13, R14 |
| 5 | SWITCH_4PIN | Buttons_Switches_THT:SW_TH_Tactile_Omron_B3F-10xx | B1, B2, B3, B4, B5 |
| 2 | 2.2u | Capacitors_SMD:C_0805_HandSoldering | C2, C3 |
| 2 | S8050 | TO_SOT_Packages_SMD:SOT-23_Handsoldering | Q1, Q2 |
| 1 | 0 | Resistors_SMD:R_1206_HandSoldering | R1 |
| 1 | 10 | Resistors_SMD:R_0805_HandSoldering | R8 |
| 1 | 100 | Potentiometers:Potentiometer_Trimmer_Bourns_3296W | RV1 |
| 1 | 100n | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 100u | Capacitors_Tantalum_SMD:CP_Tantalum_Case-U_EIA-6032-15_Hand | C4 |
| 1 | CONN_01X03 | knielsenlib:con-jack-DCJ0303 | J2 |
| 1 | CONN_01X07 | Pin_Headers:Pin_Header_Angled_1x07_Pitch2.54mm | J1 |
| 1 | CONN_01X17 | Pin_Headers:Pin_Header_Angled_1x17_Pitch2.54mm | J3 |
| 1 | ESP-12E | ESP8266:ESP-12E_SMD | U2 |
| 1 | ET024002DMU | knielsenlib:ET024002DMU_otherside | U3 |
| 1 | LP38691 | knielsenlib:TO-252-3 | U1 |
It measures 90 × 62 mm and has 2 copper layers, 1.6 mm thick.
32 parts, built around the ESP-12E and S8050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the knielsen/pcb_esp_display repository on GitHub, at the commit this page was made from: the board is pcb_esp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask knielsen before reusing the design.
CoreanXka/SlimeVR-Tracker
基于上述原因，诞生了这个项目，解决了上面的问题，并具有以下特点： - 超小尺寸，超高集成度，仅比开发板长1mm。 - 整合接口，仅用一个Type-C接口实现充电与程序下载。 - 集成最最最重要的电池保护芯片。 - 预留电池引脚接口和开关引脚接口，锂电池不再直连3.3V引脚，而是会先经过降压芯片降压后输出。 - 智能切换供电，在有外部USB供电的情况下会切断锂电池供电并进行充电，断开供电后自动使用锂电池供电。 -…
MCLEANS/AVR-BRIDGE-ATMEGA328P-PCB
PCB design for the AVR-BRIDGE ATMEGA328P test board
foorschtbar/LakeTempESP
One of my first electronic projects 2011 based on a breadboard. It has lasted almost 10 years of continuous operation.
knielsen/pcb_esp_dualboard
Dual PCB, with ST7787 display breakout board on top of ESP8266 motherboard
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported