Skip to the content
2 layersTemperature, the printed circuit board in 3D

Simple demo for the DHT11

Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
61
Pads
76
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.99 (file 20260624)
Created
11 Aug 2026
Updated
11 Aug 2026

Overview

Temperature is an open-source printed circuit board by kirprapfr, from the kirprapfr/DHT11-Demo repository on GitHub, published under the MIT licence. It is a 2-layer board with 11 parts on 61 nets.

It is built around the ARDUINO UNO R3 and DHT11. Its parts include 4 connectors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

DHT11 Temperature & Humidity Monitor

A simple Arduino project using a DHT11 temperature and humidity sensor and a small I2C OLED display.

This project was mainly made as a learning exercise for experimenting with sensors, I2C displays, Arduino, and KiCad schematics.

Features

  • Temperature measurement
  • Relative humidity measurement
  • OLED display output
  • DHT11 connected through a digital GPIO pin
  • KiCad schematic included
  • Breadboard prototype

Hardware

  • Arduino UNO-compatible board
  • DHT11 sensor
  • 0.91" I2C OLED display
  • Jumper wires
  • Breadboard

Wiring

DHT11

The schematics and wiring shown in this repository are specifically for the 3-pin DHT11 module.

DHT11Arduino
+5V
SD7
-GND

OLED

OLEDArduino UNO
VCC5V
GNDGND
SDAA4 / SDA
SCLA5 / SCL

The OLED uses I2C address 0x3C in this project.

Software

The project was made with the Arduino IDE and uses:

  • DHT11
  • Adafruit GFX
  • Adafruit SSD1306
  • Wire

The PCB files are included for experimentation and learning. This project was originally built as a breadboard prototype.

Notes

The DHT11 is a relatively slow and low-resolution sensor, so this project is intended primarily for learning and experimentation rather than precision environmental measurement.

If your DHT11 reports an error such as 253 (timeout), check the sensor wiring and jumper wires first. A bad connection can make the sensor appear completely dead.

License

This project is open source. See the repository license for details.

Parts

11
QtyValueFootprintReferences
4MountingHole_3.2mmArduino_MountingHole:MountingHole_3.2mmMH1, MH2, MH3, MH4
1AnalogConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ3
1Arduino_UNO_R3Module:Arduino_UNO_R3A1
1DHT11Sensor:Aosong_DHT11_5.5x12.0_P2.54mmU1
1Digital/PWMConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ4
1Digital/PWMConnector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_VerticalJ2
1ER_OLEDM0.91_1x-I2CDisplay:ER_OLEDM0.91_1x-I2CU2
1PowerConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ1

More from kirprapfr/DHT11-Demo

1
  • 2 layersTemperature, the printed circuit board in 3D

    Temperature

    kirprapfr/DHT11-Demo

    Simple demo for the DHT11

    8 partsMIT

Similar boards

  • 2 layers68.6 × 53.3 mmStupidDogFocuserPCB, the printed circuit board in 3D

    StupidDogFocuserPCB

    jeff-voight/StupidDogFocuser

    As open-source electronic telescope focuser

    21 parts2GPL-3.0
  • 2 layers98.1 × 101.3 mmClimatecontrolpcb, the printed circuit board in 3D

    Climatecontrolpcb

    Sharan21-cmd/climate-control-pcb-design

    A compact and efficient Climate Control PCB designed for monitoring and regulating temperature and humidity using embedded electronics.

    16 parts1
  • 2 layers111.8 × 68.6 mmAs1108, the printed circuit board in 3D

    As1108

    bit4man/temperature-display

    KICAD project for a simple temperature display on a 4 7-segment display

    10 parts
  • 2 layers248 × 122.6 mmProject 1, the printed circuit board in 3D

    Project 1

    rajsandeep2410-maker/NRF24L01-Wireless-Communication-PCB

    Designed a wireless communication system using NRF24L01 modules and Arduino, with a custom PCB layout in KiCad including transmitter and receiver sections.

    16 parts
  • 2 layers79.2 × 76.9 mmTemper, the printed circuit board in 3D

    Temper

    garvit07122005-art/electronics-projects

    This repository contains multiple Arduino-based projects:

    5 parts
  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0
  • 2 layers69.1 × 53.8 mmMotor controller, the printed circuit board in 3D

    Motor controller

    AlanFord/self-balancing-stick

    Dual Axis Reaction Wheel Inverted Pendulum

    25 parts79MIT
  • 2 layers68.6 × 53.3 mmProtogasm Board V2, the printed circuit board in 3D

    Protogasm Board V2

    Edging-Machines/Edging-Machines

    This repository is intended to contain as much information as possible about building, designing, prototyping, and using automated edging machines.

    14 parts67MIT

Questions

What parts does the Temperature use?

11 parts, built around the ARDUINO UNO R3 and DHT11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Temperature KiCad files?

From the kirprapfr/DHT11-Demo repository on GitHub, at the commit this page was made from: the board is Temperature/Temperature.kicad_pcb and its schematic Temperature/Temperature.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Temperature design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).