2 layers60 × 63 mm
ATMEGA328P AU BASE CYUSB v1.0
kgsully/MCU.ATMEGA328P-AU-Base
Base Schematic and PCB for ATMEGA328P-AU w/ USB-UART Bridge
52 parts1
2 layers60 × 63 mm
ESP32 BASE CYUSB v1.3
kgsully/MCU.ESP32-Base1Base Schematic and PCB for ESP32 WROOM w/ USB-UART Bridge
- Size
- 60 × 63 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 75
- Pads
- 211
- Tracks, vias
- 430, 52
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 25 Mar 2023
- Updated
- 25 Mar 2023
Overview
ESP32 BASE CYUSB v1.3 is an open-source printed circuit board by kgsully, from the kgsully/MCU.ESP32-Base repository on GitHub. It is a 2-layer board of 60 × 63 mm with 55 parts on 75 nets, routed with 430 tracks and 52 vias.
It is built around the ESP32-WROOM-32D, 40-100RE and CY7C65213-28PVXI, with the LDL1117S50R, LMV358IDGKR and SPX3819M5-L-3-3 among its other parts. Its parts include 15 capacitors, 12 resistors, 10 diodes, 5 ICs and 3 transistors. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.
Main components
9
ESP32-WROOM-32D
-- WiFi Modules ROHSEspressif SystemsWiFi Modules40-100RE
-RF AttenuatorsAnaren
CY7C65213-28PVXI
C0402_CSSSOP-28-208mil USB Converters ROHSInfineon TechnologiesUSB Converters
LDL1117S50R
SOT-223-40℃~+125℃ 1 1.2A 18V 250uA 350mV@(1.2A) 5V 60uVrms 87dB@(120Hz) Fixed Over Current Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
LMV358IDGKR
UncategorisedUnknown maker
SPX3819M5-L-3-3
SOT-23-5-40℃~+85℃@(Ta) 1 20V 3.3V 420mV@(100mA) 500mA 5uA 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SS8050-G
SOT-231 NPN 1.5A 100 100MHz 100nA 25V 300mW 400mV 5V NPN SOT-23 Bipolar (BJT) ROHSComchipBipolar (BJT)
BAT760-7
SOD-323Schottky DiodesDOWODMP2110U-7
SOT-23-55℃~+150℃ 1 P-Channel 1.2W 110mΩ@2.5V 1V 20V 3.5A 443pF 47pF 6nC@4.5V P-Channel SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
README.mdESP32 Base Design
ESP32 WROOM Based Base Design
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R3, R4, R7, R8, R10 |
| 5 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C2, C3, C9, C11, C16 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric | R5, R6, R11, R12 |
| 4 | 5VWM | Diode_SMD:D_0402_1005Metric | D3, D6, D7, D8 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | GRN | LED_SMD:LED_0805_2012Metric | D5, D9, D10 |
| 2 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C10, C12 |
| 2 | SS8050-G | Package_TO_SOT_SMD:SOT-23 | Q2, Q3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1, SW2 |
| 1 | 0u | Capacitor_SMD:C_0603_1608Metric | C14 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | 2.2u | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | 22u | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 40-100R | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | 470R | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 4k7 | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | BAT760-7 | Diode_SMD:D_SOD-323 | D2 |
| 1 | BLU | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | CY7C65213-28PVXI | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U5 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J2 |
| 1 | DMP2110U-7 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | ESP32-WROOM-32D | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | LDL1117S50R | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | LMV358IDGKR | Package_SO:VSSOP-8_3.0x3.0mm_P0.65mm | U3 |
| 1 | LOGO | LOGO | G*** |
| 1 | RED | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | SPX3819M5-L-3-3 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Wuerth_629105150521 | J3 |
Similar boards
- 4 layers84.9 × 90.5 mm
- 2 layers44.5 × 16.3 mm
- 2 layers28.5 × 53.6 mm
- 4 layers97.5 × 90.6 mm
ESP S3-CP-24 Platform
WhirlingBits/ESP32-S3-Platform
ESP32-S3 Development Board with SD-Card and versatile power management 5V and up to 12V
193 parts10MIT - 2 layers204.3 × 75.1 mm
PanelizedESP32
valeriyproklov/ESP32-devboard
An ESP32 devboard I designed in KiCad.
491 parts2CERN-OHL-P-2.0 - 4 layers284.2 × 102.8 mm
- 2 layers50.8 × 50.1 mm
Glove Footprint Rev2.0
bhageneder/GesticulatuionMobileManipulator
Embedded Engineering Project Summer 2024
43 parts1
Questions
How big is the ESP32 BASE CYUSB v1.3 PCB?
It measures 60 × 63 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32 BASE CYUSB v1.3 use?
55 parts, built around the ESP32-WROOM-32D, 40-100RE, CY7C65213-28PVXI and LDL1117S50R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32 BASE CYUSB v1.3 KiCad files?
From the kgsully/MCU.ESP32-Base repository on GitHub, at the commit this page was made from: the board is Electrical & PCB/ESP32_BASE_CYUSB_v1.3.kicad_pcb and its schematic Electrical & PCB/ESP32_BASE_CYUSB_v1.3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32 BASE CYUSB v1.3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask kgsully before reusing the design.