
ProPrj Segun O pcb fiverr 2026-03-03
keycard-tech/keycard-shell
Modular, fully open hardware wallet

A heart-shaped ECG board that turns your heartbeat into sound. Touch the two gold electrodes and it plays your ECG as a high-pitched tone, which a phone or laptop can decode using its microphone.
HeartThrob is an open-source printed circuit board by kevinsu926, from the kevinsu926/HeartThrob repository on GitHub, published under the MIT licence. It is a 4-layer board of 59.7 × 54 mm with 51 parts on 41 nets, routed with 223 tracks and 85 vias.
It is built around the MCP1700T-3002E/TT(MS), MCP73831T-2ACI/OT-HXY and RZM002P02T2L. Its parts include 24 resistors, 16 capacitors, 4 ICs, 3 transistors and 2 connectors.
A heart-shaped ECG board that turns your heartbeat into sound. Touch the two gold electrodes and it plays your ECG as a high-pitched tone, which a phone or laptop can decode using its microphone. It has no Bluetooth, no Wi-Fi and no firmware.
flowchart LR
A[Fingers on<br/>electrodes] --> B[AD8233<br/>ECG amplifier]
B --> C[LTC6990<br/>oscillator]
C --> D[Piezo<br/>~18.5 kHz tone]
D --> E[Phone / laptop<br/>microphone]
The top trace is what the phone shows: P, QRS and T waves for each beat, with heart rate taken from the time between R peaks. The bottom trace is the same signal as the microphone hears it: a tone near 18.5 kHz whose pitch rises and falls with the ECG. (Simulated example.)
When nobody is touching the electrodes, the board detects that the leads are off and switches the oscillator off to save battery.
The board runs on a small 1S LiPo battery soldered to pads on the back, and charges over USB-C. A 3.0 V regulator powers the circuit, and a P-FET protects it if the battery is connected backwards.
hardware/Heartthrob/
KiCad 10 project: schematic, 4-layer PCB layout, design rules and custom footprints. Open Heartthrob.kicad_pro.hardware/Heartthrob/Render/
3D renders of the front and back.hardware/Heartthrob/Documentation/
Schematic PDF, per-layer PCB plots, and earlier design snapshots in Archive/.hardware/Heartthrob/illustrations/
Figures used in this README.Note: This is a hobby project, not a medical device. Don't use it for diagnosis, and don't wear it while it's plugged in to charge.
Based on SiBowald's ECG PCB business card, redesigned by Kevin Su as a rechargeable, heart-shaped board.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10M | Resistor_SMD:R_0201_0603Metric | R1, R2, R3, R10, R11, R12 |
| 5 | 1M | Resistor_SMD:R_0201_0603Metric | R7, R9, R14, R19, R22 |
| 4 | 10uF | ECG_Business_Card_Library:C_0402_1005Metric | C2, C24, C27, C28 |
| 4 | 1uF | ECG_Business_Card_Library:C_0402_1005Metric | C7, C9, C25, C26 |
| 3 | RZM002P02T2L | ECG_Business_Card_Library:SOT-723 | Q1, Q2, Q3 |
| 2 | 100 | Resistor_SMD:R_0201_0603Metric | R13, R18 |
| 2 | 100nF | ECG_Business_Card_Library:C_0402_1005Metric | C1, C23 |
| 2 | 1nF | ECG_Business_Card_Library:C_0402_1005Metric | C6, C14 |
| 2 | 330k | Resistor_SMD:R_0201_0603Metric | R4, R5 |
| 2 | 5.1k | Resistor_SMD:R_0201_0603Metric | R24, R25 |
| 2 | 5.6nF | ECG_Business_Card_Library:C_0402_1005Metric | C4, C5 |
| 2 | 510k | Resistor_SMD:R_0201_0603Metric | R6, R15 |
| 1 | 0.22uF | ECG_Business_Card_Library:C_0402_1005Metric | C3 |
| 1 | 10k | Resistor_SMD:R_0201_0603Metric | R23 |
| 1 | 1k | Resistor_SMD:R_0201_0603Metric | R26 |
| 1 | 2.4M | Resistor_SMD:R_0201_0603Metric | R16 |
| 1 | 3.3uF | ECG_Business_Card_Library:C_0402_1005Metric | C8 |
| 1 | 680k | Resistor_SMD:R_0201_0603Metric | R8 |
| 1 | 82k | Resistor_SMD:R_0201_0603Metric | R17 |
| 1 | AD8233 | AD8233:20-WLCPS-2MMX1.7MM | U1 |
| 1 | LTC6990 | ECG_Business_Card_Library:SOT95P280X100-6N | U4 |
| 1 | LiPo 1S | smdpads:LiPo_SMD_Pads_2x3mm_P4mm | J1 |
| 1 | MCP1700T-3002E/TT | Package_TO_SOT_SMD:SOT-23 | U5 |
| 1 | MCP73831T-2ACI/OT | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | Red (charging) | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | Speaker_Ultrasound | Piezo:Piezo_12mm | LS1 |
| 1 | USB-C | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |

keycard-tech/keycard-shell
Modular, fully open hardware wallet

feboyfierlyan/nodi
Nodi — a custom PCB digital companion charm. KiCad hardware, RISC-V firmware, a shared C/WASM core, and an interactive 3D simulator.


foggyflute/Voyager65
Fully versatile 65% keyboard PCB. Simplified variants available.

Projeto-Guarda-Rios/PCB
O repositório para a PCB do Projeto Guarda Rios! Inclui todos os ficheiros relacionados com a PCB!


zeugmaster/nucula-board
Nucula Board: an ESP32-C3 hardware prototype with USB-C, PN7160 NFC, OLED and detachable keyboard. KiCad sources and manufacturing files.

It measures 59.7 × 54 mm and has 4 copper layers, 0.8 mm thick.
51 parts, built around the MCP1700T-3002E/TT(MS), MCP73831T-2ACI/OT-HXY and RZM002P02T2L. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the kevinsu926/HeartThrob repository on GitHub, at the commit this page was made from: the board is hardware/Heartthrob/Heartthrob.kicad_pcb and its schematic hardware/Heartthrob/Heartthrob.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).