

- Size
- 100 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 92
- Pads
- 368
- Tracks, vias
- 1,367, 78
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 10 May 2026
- Updated
- 13 May 2026
Overview
Stplus is an open-source printed circuit board by KenWillmott, from the KenWillmott/SST-6809-V2.2 repository on GitHub, published under the MIT licence. It is a 4-layer board of 100 × 100 mm with 50 parts on 92 nets, routed with 1,367 tracks and 78 vias.
It is built around the MC68B09CP, 74HCT02D and 74HCT138D, with the 74HCT139D, 74HCT20D and 74HCT273D among its other parts. Its parts include 14 capacitors, 12 ICs, 6 connectors, 3 diodes and 2 resistors.
Main components
9MC68B09CP
PDIP-40PDIP-40 Microcontrollers (MCU/MPU/SOC)Rochester Electronics, LLCMicrocontrollers (MCU/MPU/SOC)74HCT02D
SO-14-40℃~+125℃ 19ns@4.5V,50pF 2 2V 2uA 3.7V 4 4.5V~5.5V 400mV 4mA 4mA 74HCT Series 800mV NOR Gate Overvoltage-tolerant input SOIC-14 Logic Gates ROHSNexperiaGates74HCT138D
SO-16-40℃~+125℃ 160uA 20ns@4.5V,50pF 3/8 4.5V~5.5V 4mA 4mA 74HCT Decoder Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches / Encoders & Decoders / Multiplexers74HCT139D
SO-16-40℃~+125℃ 160uA 16ns@4.5V,50pF 4.5V~5.5V 4/8 4mA 4mA 74HCT Decoder Single Supply SO-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches, Multiplexers, Decoders74HCT20D
SO-142 28ns@4.5V,50pF 4 NAND Gate SOIC-14 Logic Gates ROHSNexperiaLogic Gates74HCT273D
SOIC-20-300mil-40℃~+125℃ 12ns 3.5pF 30ns@4.5V,50pF 36MHz 3ns 4.5V~5.5V 4mA 5.2mA 74HCT Series 8 8uA D-Type Reset Rising Edge SOIC-20-300mil Flip Flops ROHSNexperiaFlip FlopsAS6C4008-55PCN
PDIP-320℃~+70℃ 2.7V~5.5V 30mA 4Mbit 4uA 55ns Parallel Port (Parallel) PDIP-32 SRAM ROHSAlliance MemorySRAMDS1233
SOT-223SOT-223 Supervisor and Reset ICs ROHSAnalog DevicesSupervisor And Reset ICsDS1813-5+
TO-92-3-40℃~+85℃@(Ta) 1 1.2V~5.5V 150ms 4.75V Active Low No Open Drain Voltage Monitor Yes TO-92-3 Supervisor and Reset ICs ROHSAnalog DevicesSupervisor And Reset ICs
README
README.mdSST-6809-V2.2
This is the working repository for the most current and only recommended version of the SST-6809. It contains all of the files and reference documents, and some documentation. However, the full documentation set will be hosted elsewhere, location is yet to be determined. For now, you can follow the documentation in the old repo "SST-6809" which is mostly concordant with this new version.
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_THT:C_Disc_D8.0mm_W2.5mm_P5.00mm | C3, C4, C5, C6, C7, C8, C9, C11, C13, C14 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 3 | Jumper_3_Bridged12 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP3, JP4 |
| 2 | 20pF | Capacitor_THT:C_Disc_D8.0mm_W2.5mm_P5.00mm | C1, C2 |
| 1 | 100nF | Capacitor_THT:C_Disc_D9.0mm_W2.5mm_P5.00mm | C12 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 10uF | Capacitor_THT:C_Disc_D9.0mm_W2.5mm_P5.00mm | C10 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D2 |
| 1 | 3.0V | Battery:BatteryHolder_Keystone_103_1x20mm | BT1 |
| 1 | 4.7k | Resistor_THT:R_Array_SIP9 | RN1 |
| 1 | 4.7k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | 74HCT02 | Package_DIP:DIP-14_W7.62mm_LongPads | U5 |
| 1 | 74HCT138 | Package_DIP:DIP-16_W7.62mm_LongPads | U8 |
| 1 | 74HCT139 | Package_DIP:DIP-16_W7.62mm_LongPads | U12 |
| 1 | 74HCT20 | Package_DIP:DIP-14_W7.62mm_LongPads | U11 |
| 1 | 74HCT273 | Package_DIP:DIP-20_W7.62mm_LongPads | U4 |
| 1 | 8.0 MHz | Crystal:Crystal_HC18-U_Vertical | Y1 |
| 1 | AS6C4008-55PCN | Package_DIP:DIP-32_W15.24mm_LongPads | U6 |
| 1 | CXO_DIP8 | Oscillator:Oscillator_DIP-8 | X1 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J4 |
| 1 | Conn_02x07_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x07_P2.54mm_Vertical | J5 |
| 1 | Conn_02x20_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J6 |
| 1 | DS1210 | Package_DIP:DIP-8_W7.62mm_Socket_LongPads | U10 |
| 1 | DS1233 | Package_TO_SOT_THT:TO-92L_Inline | U9 |
| 1 | DS1813 | Package_TO_SOT_THT:TO-92L_Inline | U7 |
| 1 | MC68B09 | Package_DIP:DIP-40_W15.24mm_LongPads | U1 |
| 1 | MC68B50 | Package_DIP:DIP-24_W15.24mm_LongPads | U2 |
| 1 | PWR | LED_THT:LED_D3.0mm | D3 |
| 1 | Reset | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1 |
| 1 | SST39SF010 | Library:PLCC-32_THT-Socket | U3 |
| 1 | STAT | LED_THT:LED_D3.0mm | D1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J2 |
| 1 | VBAT | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | JP2 |
Similar boards
- 4 layers100 × 100 mm

- 2 layers127 × 127 mm

Morseboard-8088
ifilot/morseboard-8088
Single board computer designed around the 8088 processor
61 parts - 2 layers300 × 200 mm

DATX JC100
Julesc013/project-carbon
Hardware and software for custom CPUs, FPUs, and computer systems.
172 parts - 2 layers297.2 × 180.3 mm

- 4 layers161.1 × 82.9 mm

- 2 layers99.1 × 76.8 mm

- 2 layers389 × 136.2 mm

- 2 layers235 × 158.8 mm

Gigatron
flypie/Gigatron
This is a version of the files from https://gigatron.io/ altered to work on a vanilla KiCAD 5.1.6. Changes are minimal in the schematic and PCB, layout has only been changed where dimensions or orientations changed as a…
151 parts2
Questions
How big is the Stplus PCB?
It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Stplus use?
50 parts, built around the MC68B09CP, 74HCT02D, 74HCT138D and 74HCT139D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stplus KiCad files?
From the KenWillmott/SST-6809-V2.2 repository on GitHub, at the commit this page was made from: the board is KiCad/stplus.kicad_pcb and its schematic KiCad/stplus.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stplus design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).