2 layers22 × 18 mm
2 layers114.5 × 100.5 mm
DZZY
KarlK90/DZZY1Barebones 5x6 Gamepad with thumb keys using Kailh Choc V1 switches.
- Size
- 114.5 × 100.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 96
- Nets
- 64
- Pads
- 471
- Tracks, vias
- 586, 65
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20210424)
- Created
- 21 May 2021
- Updated
- 22 May 2021
Overview
DZZY is an open-source printed circuit board by KarlK90, from the KarlK90/DZZY repository on GitHub. It is a 2-layer board of 114.5 × 100.5 mm with 96 parts on 64 nets, routed with 586 tracks and 65 vias.
It is built around the GD32VF103CBT6, M95512-WMN6P and USBLC6-4SC6, with the XC6206P332MR among its other parts. Its parts include 30 switches, 29 diodes, 9 capacitors, 8 resistors and 4 ICs. It belongs with the keyboards and input boards and the RISC-V boards of this library.
Main components
4
GD32VF103CBT6
LQFP-48(7x7)108MHz 128KB 12bit 12bit 37 FLASH Others LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSGigaDevice Semicon BeijingMicrocontrollers (MCU/MPU/SOC)
M95512-WMN6P
SOIC-8-40℃~+85℃ 16MHz 2.5V~5.5V 200 Years 4,000,000 Cycles 512Kbit 5ms Hardware write protection function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function、Built-in write enable latch (WEL) SPI SOIC-8 EEPROM ROHSSTMicroelectronicsEEPROM
USBLC6-4SC6
SOT-23-6-55℃~+125℃ 0.3pF 15V 300W@8/20us 4.7A@8/20us 5V 6V 80nA ESD Four channels IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Unidirectional SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
96| Qty | Value | Footprint | References |
|---|---|---|---|
| 28 | D | prettylib:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +12 |
| 24 | SW | prettylib:SW_PG1350_reversible | S1, S2, S10, S15, S16, S17, S18, S19, S20, S21, S22, S23, S24, S25, S26, S27 +8 |
| 5 | 100n | prettylib:SMD-0603 | C7, C8, C10, C11, C12 |
| 4 | SW | prettylib:SW_PG1350_0.5u_stagger_reversible | S11, S12, S13, S14 |
| 3 | 5k1 | prettylib:SMD-0603 | R1, R3, R4 |
| 2 | 10u | prettylib:SMD-0603 | C9, C13 |
| 2 | 20p | prettylib:SMD-0603 | C15, C16 |
| 2 | 33 | prettylib:SMD-0603 | R6, R7 |
| 2 | DZZY_LOGO | prettylib:dzzy_logo | G1, G2 |
| 1 | 1k5 | prettylib:SMD-0603 | R2 |
| 1 | 220 | prettylib:SMD-0603 | R12 |
| 1 | 2k2 | prettylib:SMD-0603 | R5 |
| 1 | 8MHz | prettylib:Crystal_SMD_3225-4Pin_3.2x2.5mm | HSE1 |
| 1 | BOOT0 | prettylib:SW_SPST_TS_1088 | S30 |
| 1 | COL1 | prettylib:TestPoint | TP10 |
| 1 | COL2 | prettylib:TestPoint | TP11 |
| 1 | COL3 | prettylib:TestPoint | TP12 |
| 1 | COL4 | prettylib:TestPoint | TP13 |
| 1 | COL5 | prettylib:TestPoint | TP14 |
| 1 | COL6 | prettylib:TestPoint | TP15 |
| 1 | GD32VF103CBT6 | prettylib:LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | JTAG/SWD | prettylib:Debug_Header_1x07_P2.54mm_Vertical | J1 |
| 1 | LED | prettylib:LED-0603_flipable | D7 |
| 1 | M95512-WMN6P | prettylib:SOIC-8 | U3 |
| 1 | PC | prettylib:HRO-TYPE-C-31-M-12-HandSoldering-NoSBU | P1 |
| 1 | RESET | prettylib:SW_SPST_TS_1088 | S29 |
| 1 | ROW1 | prettylib:TestPoint | TP5 |
| 1 | ROW2 | prettylib:TestPoint | TP6 |
| 1 | ROW3 | prettylib:TestPoint | TP7 |
| 1 | ROW4 | prettylib:TestPoint | TP8 |
| 1 | ROW5 | prettylib:TestPoint | TP9 |
| 1 | USBLC6-4SC6 | prettylib:SOT-23-6_flipable | U1 |
| 1 | XC6206P332MR | prettylib:SOT-23 | U2 |
Questions
How big is the DZZY PCB?
It measures 114.5 × 100.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DZZY use?
96 parts, built around the GD32VF103CBT6, M95512-WMN6P, USBLC6-4SC6 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DZZY KiCad files?
From the KarlK90/DZZY repository on GitHub, at the commit this page was made from: the board is dzzy.kicad_pcb and its schematic dzzy.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DZZY design in my own project?
Its repository states no licence, so its author keeps all rights: ask KarlK90 before reusing the design.
Similar boards
- 4 layers59.2 × 66 mm
- 4 layers94.4 × 72.8 mm
RP2040 base
Twisted-Fields/rp2040-motor-controller
A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.
325 parts419 - 2 layers28 × 30 mm
- 2 layers51 × 18.5 mm
Entree
tuna-f1sh/entree
Entree is a USB-C CAN interface designed to fully support CANnectivity - gets the CAN party started!
78 parts89 - 2 layers99.8 × 99.8 mm
Stmbl 5.0
freakontrol/stmbl
THE AUTHORS OF THIS SOFTWARE ACCEPT ABSOLUTELY NO LIABILITY FOR ANY HARM OR LOSS RESULTING FROM ITS USE. IT IS EXTREMELY UNWISE TO RELY ON SOFTWARE ALONE FOR SAFETY.
432 parts53GPL-3.0 - 2 layers85 × 50 mm
APPMC
tdjastrzebski/All-Purpose-Power-Micro-Controller
General purpose power controller, capable of driving soldering irons using different voltages and probe types.
117 parts40 - 2 layers194 × 114.1 mm
