Skip to the content
2 layers82 × 100 mmRat, the printed circuit board in 3D
Size
82 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
46
Nets
31
Pads
120
Tracks, vias
234, 12
Pours
5
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
4 Jul 2025
Updated
15 Jun 2026

Overview

Rat is an open-source printed circuit board by kanengomibako, from the kanengomibako/EffectsPedals repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 82 × 100 mm with 46 parts on 31 nets, routed with 234 tracks and 12 vias.

It is built around the LM358, 1N4148W and GS1010FL. Its parts include 15 resistors, 12 capacitors, 4 diodes, 3 connectors and 3 switches.

Main components

3

README

PedalMeetingHeadphoneAmp/README.md

Pedal Meeting Headphone Amp

Pedal Meeting Headphone Amp Picture

エフェクター展示会の試奏ブースでのコミュニケーションを円滑にするために設計されたヘッドフォンアンプです。ギター/ベースの音と会話用のマイク音声をミックスし、ヘッドフォンで聴くことができます。試奏者と出展者が音を共有できると共に、ヘッドフォンを外さずに会話することが可能となります。

※ 電源は、DC9V(センターマイナス)出力のACアダプターで、0.3A以上の電流出力が可能なものを使用してください。

■ 入力

それぞれ独立したゲイン調整を備えています。ゲインを上げ過ぎるとハウリングが起こることがありますのでご注意ください。

  • INST

    楽器側の音声出力を接続します。アンプ・キャビネットシミュレータからの接続を想定しています。ゲインは基本的に中央で固定し、微調整として使用してください。

  • MIC1/MIC2

    外部マイクを接続します。48Vファンタム電源が必要なマイクには対応していません。

  • MIC3

    本体トップ面にあるマイクです。外部マイクがない場合でも、会話を拾うことが可能です。

■ 出力

楽器の音とマイクの音をそれぞれ出力ボリュームで調整できます。

  • PHONES A/B

    試奏者用、出展者用のヘッドフォンを接続します。

  • LINE A/B

    外部録音機器を接続できます。

■ スイッチ

  • MIC ON/OFF

    すべてのマイク入力を一括でミュートします。マイクが楽器の生音を拾うため、会話時以外はマイクをOFF(LED消灯)にすることをお勧めします。

  • MIC 5V

    プラグインパワー方式のコンデンサーマイク(BEHRINGER BC LAV 等)を使用する際にONにします。ダイナミックマイク接続時はOFFにします。48Vファンタム電源が必要なマイクには対応していません。

■ 資料

■ 主な仕様
入力インピーダンス47kΩ(INST)
10kΩ(MIC)
出力インピーダンス1 kΩ(LINE)
10Ω(PHONES)
最大出力レベル2.5 Vrms(LINE)
50 mW + 50 mW, 32Ω(PHONES)
コントロールMIC ON/OFFスイッチ MIC 5Vスイッチ GAINつまみ × 4 VOLつまみ × 4
インジケーター赤色LED(電源ON)
青色LED(マイクON)
接続端子INST MIC1/2 PHONES A/B LINE A/B 電源入力端子
消費電流40 mA(無信号時)
300 mA(最大出力時)
外形寸法幅 100 mm × 奥行 130 mm × 高さ 57 mm
質量550 g

Parts

46
QtyValueFootprintReferences
410kmyFoot:my_R_1608(0603)_HandSolderingR8, R10, R13, R14
3100kAmyFoot:my_pot_slide_45mm_travelRV1, RV2, RV3
31MmyFoot:my_R_1608(0603)_HandSolderingR1, R2, R9
31kmyFoot:my_R_2012(0805)_HandSolderingR5, R6, R11
3SW_3PDTmyFoot:my_sw_footSW1, SW2, SW3
3smyFoot:my_SmallPad_0-8mmDrill*, *, *
2*MountingHole:MountingHole_3.2mm_M3*, *
2100umyFoot:my_C_Elec_6.3C10, C12
21N4148WmyFoot:my_D_SOD-123D1, D2
222nmyFoot:my_C_2012(0805)_HandSolderingC1, C8
24.7umyFoot:my_C_Elec_4C3, C6
247RmyFoot:my_R_2012(0805)_HandSolderingR3, R12
10.1umyFoot:my_C_1608(0603)_HandSolderingC11
11.5kmyFoot:my_R_1608(0603)_HandSolderingR7
1100pmyFoot:my_C_1608(0603)_HandSolderingC5
11nmyFoot:my_C_1608(0603)_HandSolderingC4
11umyFoot:my_C_Elec_4C9
12.2umyFoot:my_C_Elec_4C2
13.3nmyFoot:my_C_1608(0603)_HandSolderingC7
14.7kmyFoot:my_R_1608(0603)_HandSolderingR15
1560RmyFoot:my_R_2012(0805)_HandSolderingR4
1DC_JackmyFoot:my_DC_JackJ2
1GS1010FLmyFoot:my_D_GS1010FLD3
1INPUTmyFoot:my_Phone_Jack_DaierJ1
1LEDLED_THT:LED_D3.0mmD4
1LM358myFoot:my_SOIC-8_3.9x4.9mm_Pitch1.27mmU1
1OUTPUTmyFoot:my_Phone_Jack_DaierJ3

More from kanengomibako/EffectsPedals

12
  • 2 layers55.4 × 66 mmOwmBoard, the printed circuit board in 3D

    OwmBoard

    kanengomibako/EffectsPedals

    166 parts14Unlicense
  • 2 layers112 × 80 mmBddi v1ep, the printed circuit board in 3D

    Bddi v1ep

    kanengomibako/EffectsPedals

    146 parts14Unlicense
  • 2 layers90 × 100 mmBd2wl, the printed circuit board in 3D

    Bd2wl

    kanengomibako/EffectsPedals

    144 parts14Unlicense
  • 2 layers54 × 83 mmMTZone, the printed circuit board in 3D

    MTZone

    kanengomibako/EffectsPedals

    120 parts14Unlicense
  • 4 layers49.5 × 49.5 mmOwmH7D, the printed circuit board in 3D

    OwmH7D

    kanengomibako/EffectsPedals

    118 parts14Unlicense
  • 2 layers99.1 × 80 mmTremolec, the printed circuit board in 3D

    Tremolec

    kanengomibako/EffectsPedals

    103 parts14Unlicense
  • 2 layers61 × 100 mmBd2op, the printed circuit board in 3D

    Bd2op

    kanengomibako/EffectsPedals

    102 parts14Unlicense
  • 2 layers100 × 100 mmBddi v1el, the printed circuit board in 3D

    Bddi v1el

    kanengomibako/EffectsPedals

    94 parts14Unlicense
  • 2 layers73 × 100 mmDs1, the printed circuit board in 3D

    Ds1

    kanengomibako/EffectsPedals

    88 parts14Unlicense
  • 2 layers49.5 × 54.6 mmOwmAN, the printed circuit board in 3D

    OwmAN

    kanengomibako/EffectsPedals

    88 parts14Unlicense

Similar boards

  • 2 layers73 × 99.8 mmSodium, the printed circuit board in 3D

    Sodium

    kanengomibako/Sodium

    85 parts14Unlicense
  • 2 layers65.7 × 51 mm(KiCad)DriveUnit B series(ver2.0), the printed circuit board in 3D

    (KiCad)DriveUnit B series(ver2.0)

    issaimaru/MoterDriver_v1

    80A級モータードライバ 制作期間:2022/01/18頃~ 名前:DriveUnit Bseries

    67 parts5Apache-2.0
  • 2 layers83 × 100 mmMicroNaos, the printed circuit board in 3D

    MicroNaos

    rn-t/MicroNaos_open

    113 parts4
  • 2 layers60 × 50 mmSaposenBoard, the printed circuit board in 3D

    SaposenBoard

    hide4096/SaposenBoard

    85 parts2
  • 2 layers100 × 100 mmSpringRobocon2026 mainboard, the printed circuit board in 3D

    SpringRobocon2026 mainboard

    KeioRoboticsAssociation/SpringRobocon2026_mainboard

    関東春ロボコン2026のメイン基板です

    74 parts2
  • 2 layers150 × 100 mmSatelliteController2.0, the printed circuit board in 3D

    SatelliteController2.0

    tokai-student-rocket-project/Gen6-GSE-Elec

    第6世代自動GSE電装系

    228 parts2MIT
  • 2 layers38.1 × 220.3 mmWifi voice clock v3, the printed circuit board in 3D

    Wifi voice clock v3

    ktmizugaki/wifi-voice-clock

    ESP32 Small Alarm Clock

    78 parts1

Questions

How big is the Rat PCB?

It measures 82 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rat use?

46 parts, built around the LM358, 1N4148W and GS1010FL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rat KiCad files?

From the kanengomibako/EffectsPedals repository on GitHub, at the commit this page was made from: the board is LM358RAT/KiCad/rat.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rat design in my own project?

Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).