

- Size
- 49.5 × 54.6 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 88
- Nets
- 47
- Pads
- 242
- Tracks, vias
- 441, 40
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 4 Jul 2025
- Updated
- 15 Jun 2026
Overview
OwmAN is an open-source printed circuit board by kanengomibako, from the kanengomibako/EffectsPedals repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 49.5 × 54.6 mm with 88 parts on 47 nets, routed with 441 tracks and 40 vias.
It is built around the OPA1679ID and NJM7805SDL1-TE1. Its parts include 37 resistors, 27 capacitors, 10 connectors, 5 ICs and 1 diode.
Main components
2OPA1679ID
SOIC-14-18V~-2.25V、2.25V~18V、4.5V~36V -40℃~+85℃ 0.0001% 2.5mA 4-Channel ESD protection SOIC-14 Audio Amplifiers ROHSTexas InstrumentsAudio AmplifiersNJM7805SDL1-TE1
TO-252-40℃~+125℃ 1 1.5A 2.2V@(1.5A) 35V 4.2mA 45uVrms 5V 78dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSNisshinbo Micro Devices Inc.Voltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
PedalMeetingHeadphoneAmp/README.mdPedal Meeting Headphone Amp

エフェクター展示会の試奏ブースでのコミュニケーションを円滑にするために設計されたヘッドフォンアンプです。ギター/ベースの音と会話用のマイク音声をミックスし、ヘッドフォンで聴くことができます。試奏者と出展者が音を共有できると共に、ヘッドフォンを外さずに会話することが可能となります。
※ 電源は、DC9V(センターマイナス)出力のACアダプターで、0.3A以上の電流出力が可能なものを使用してください。
■ 入力
それぞれ独立したゲイン調整を備えています。ゲインを上げ過ぎるとハウリングが起こることがありますのでご注意ください。
-
INST
楽器側の音声出力を接続します。アンプ・キャビネットシミュレータからの接続を想定しています。ゲインは基本的に中央で固定し、微調整として使用してください。
-
MIC1/MIC2
外部マイクを接続します。48Vファンタム電源が必要なマイクには対応していません。
-
MIC3
本体トップ面にあるマイクです。外部マイクがない場合でも、会話を拾うことが可能です。
■ 出力
楽器の音とマイクの音をそれぞれ出力ボリュームで調整できます。
-
PHONES A/B
試奏者用、出展者用のヘッドフォンを接続します。
-
LINE A/B
外部録音機器を接続できます。
■ スイッチ
-
MIC ON/OFF
すべてのマイク入力を一括でミュートします。マイクが楽器の生音を拾うため、会話時以外はマイクをOFF(LED消灯)にすることをお勧めします。
-
MIC 5V
プラグインパワー方式のコンデンサーマイク(BEHRINGER BC LAV 等)を使用する際にONにします。ダイナミックマイク接続時はOFFにします。48Vファンタム電源が必要なマイクには対応していません。
■ 資料
| ■ 主な仕様 | |
|---|---|
| 入力インピーダンス | 47kΩ(INST) 10kΩ(MIC) |
| 出力インピーダンス | 1 kΩ(LINE) 10Ω(PHONES) |
| 最大出力レベル | 2.5 Vrms(LINE) 50 mW + 50 mW, 32Ω(PHONES) |
| コントロール | MIC ON/OFFスイッチ MIC 5Vスイッチ GAINつまみ × 4 VOLつまみ × 4 |
| インジケーター | 赤色LED(電源ON) 青色LED(マイクON) |
| 接続端子 | INST MIC1/2 PHONES A/B LINE A/B 電源入力端子 |
| 消費電流 | 40 mA(無信号時) 300 mA(最大出力時) |
| 外形寸法 | 幅 100 mm × 奥行 130 mm × 高さ 57 mm |
| 質量 | 550 g |
Parts
88| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | myFoot:my_R_1608(0603)_HandSoldering | R4, R5, R6, R12, R13, R14, R19, R20, R27, R28, R33, R34 |
| 6 | 100R | myFoot:my_R_2012(0805)_HandSoldering | R7, R8, R15, R16, R23, R31 |
| 5 | 100n | myFoot:my_C_1608(0603)_HandSoldering | C20, C22, C23, C26, C27 |
| 4 | 100k | myFoot:my_R_1608(0603)_HandSoldering | R24, R32, R35, R36 |
| 4 | 100p | myFoot:my_C_1608(0603)_HandSoldering | C2, C3, C6, C7 |
| 4 | 1n | myFoot:my_C_1608(0603)_HandSoldering | C9, C10, C14, C15 |
| 4 | 2.2k | myFoot:my_R_1608(0603)_HandSoldering | R21, R22, R29, R30 |
| 4 | 20k | myFoot:my_R_1608(0603)_HandSoldering | R17, R18, R25, R26 |
| 4 | 220p | myFoot:my_C_1608(0603)_HandSoldering | C11, C12, C16, C17 |
| 4 | AGND | myFoot:my_SmallPad_0-8mmDrill | J7, J8, J9, J10 |
| 3 | 100u | myFoot:my_C_D6.3mm_P2.50mm | C19, C24, C25 |
| 2 | 100n | myFoot:my_C_3225(1210)_HandSoldering | C1, C5 |
| 2 | 10n | myFoot:my_C_1608(0603)_HandSoldering | C4, C8 |
| 2 | 10u | myFoot:my_C_Elec_5 | C13, C18 |
| 2 | 1M | myFoot:my_R_1608(0603)_HandSoldering | R3, R11 |
| 2 | 1k | myFoot:my_R_2012(0805)_HandSoldering | R2, R10 |
| 2 | 2.2M | myFoot:my_R_1608(0603)_HandSoldering | R1, R9 |
| 2 | OPA1679 | myFoot:my_TSSOP-14 | U1, U2 |
| 1 | 0R | myFoot:my_R_P7.62mm_Horizontal | R37 |
| 1 | 10u | myFoot:my_C_3216(1206)_HandSoldering | C21 |
| 1 | 1N4007 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | 330R | myFoot:my_R_2012(0805)_HandSoldering | FB1 |
| 1 | Conn_01x12 | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J5 |
| 1 | LIN | myFoot:my_SmallPad_0-8mmDrill | J1 |
| 1 | LOUT | myFoot:my_SmallPad_0-8mmDrill | J3 |
| 1 | MCWI03-12S05 | myFoot:MCWI03-12S05 | U3 |
| 1 | NJM7805SDL1 | myFoot:my_TO-252-3 | U5 |
| 1 | RIN | myFoot:my_SmallPad_0-8mmDrill | J2 |
| 1 | ROUT | myFoot:my_SmallPad_0-8mmDrill | J4 |
| 1 | TA78L05F | Package_TO_SOT_SMD:SOT-89-3 | U4 |
| 1 | Vcc | myFoot:my_SmallPad_0-8mmDrill | J6 |
The 81 most common of 88 parts.
More from kanengomibako/EffectsPedals
12- 2 layers55.4 × 66 mm

- 2 layers112 × 80 mm

- 2 layers90 × 100 mm

- 2 layers100 × 80 mm

- 2 layers54 × 83 mm

- 4 layers49.5 × 49.5 mm

- 2 layers99.1 × 80 mm

- 2 layers61 × 100 mm

- 2 layers100 × 100 mm

- 2 layers100 × 100 mm

- 2 layers73 × 100 mm

- 2 layers54.6 × 48.3 mm

Similar boards
- 2 layers150 × 100 mm

- 2 layers34.7 × 1 mm

- 2 layers132.5 × 82.5 mm

- 2 layers70 × 91.5 mm

- 2 layers80 × 60 mm

- 2 layers68.6 × 53.3 mm

- 2 layers79.9 × 57 mm

- 4 layers65 × 85 mm

Questions
How big is the OwmAN PCB?
It measures 49.5 × 54.6 mm and has 2 copper layers, 1.6 mm thick.
What parts does the OwmAN use?
88 parts, built around the OPA1679ID and NJM7805SDL1-TE1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the OwmAN KiCad files?
From the kanengomibako/EffectsPedals repository on GitHub, at the commit this page was made from: the board is OwmPedalH7/KiCad_AN/owmAN.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the OwmAN design in my own project?
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
