4 layers120.6 × 142 mm
Noname
ka6s/rp_adapter
Red Pitaya Shield for HPSDR 1W Transceiver. Controls EB104.ru Hermes RX filter, 300W PA Transmit filter.
92 parts7
4 layers170.2 × 135.1 mm
Temp
ka6s/rp_adapter7Red Pitaya Shield for HPSDR 1W Transceiver. Controls EB104.ru Hermes RX filter, 300W PA Transmit filter.
- Size
- 170.2 × 135.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 147
- Nets
- 207
- Pads
- 618
- Tracks, vias
- 538, 82
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 25 Oct 2016
- Updated
- 2 Dec 2017
Overview
Temp is an open-source printed circuit board by ka6s, from the ka6s/rp_adapter repository on GitHub. It is a 4-layer board of 170.2 × 135.1 mm with 147 parts on 207 nets, routed with 538 tracks and 82 vias.
It is built around the CY8C4247AXI-M485, KA278R05TU and KA278R12CTU, with the ULN2003, ADT1.5-1 and DB15 among its other parts. Its parts include 56 capacitors, 32 connectors, 27 resistors, 12 ICs and 7 inductors. It belongs with the radio and wireless boards of this library.
Main components
6
CY8C4247AXI-M485
TQFP-64ARM Cortex-M0 TQFP-64(14x14) Microcontrollers (MCU/MPU/SOC) ROHSInfineon TechnologiesMicrocontrollers (MCU/MPU/SOC)
KA278R05TU
TO-220F-4L-20℃~+80℃ 1 10mA 2A 35V 500mV@(2A) 55dB 5V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input overvoltage protection Positive TO-220F-4L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsKA278R12CTU
TO-220F-4L-20℃~+80℃@(Ta) 1 10mA 12V 29V 2A 500mV@(2A) 55dB Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input overvoltage protection Positive TO-220F-4L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSonsemiVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
ULN2003
SOP-161.1V@250uA,100mA 25pF 2V 30V 500mA 50uA 50uA Seven channels SOP-16 Darlington Transistor Arrays ROHSBLDarlington Transistor Arrays
ADT1.5-1
SMD-6PSMD-6P New Arrivals ROHSMini-CircuitsUncategorisedDB15
-Coaxial Connectors (RF)Belden
README
README.mdrp_adapter : v4
rp_adapter
This is the layout of the 4th iteration of this board. Currently the design in this directory is the transceiver consisting of a connector to the Red Pitaya, the OpenHPSDR TAPR LPU, the OpenHPSDR TAPR T/R board, a 1W PA taken from the OpenHPSDR Penelope board, and a simple 18db ish LNA.
The connecitivy is built to interface to an external amplifier, the Hermes RX Filter from EB104.ru and the 300W LPF from EB104.ru. You need to get the amp keying from the EB104.ru LPF board.
Enjoy
Parts
147| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 0.1uF | Capacitors_SMD:C_1206_HandSoldering | C4, C10, C11, C26, C27, C28, C29, C31, C33, C34, C35, C36, C38, C39, C44, C45 +6 |
| 12 | 100pF | Capacitors_SMD:C_1206_HandSoldering | C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 |
| 10 | 1uF | Capacitors_SMD:C_1210_HandSoldering | C1, C2, C3, C5, C7, C9, C24, C25, C32, C56 |
| 8 | 4.7K | Resistors_SMD:R_1206_HandSoldering | R1, R2, R3, R4, R5, R25, R26, R27 |
| 7 | 0 | Resistors_SMD:R_1206_HandSoldering | R6, R7, R8, R9, R10, R11, R12 |
| 6 | BNC | Sockets_BNC:BNC_Socket_TYCO-AMP_LargePads | P8, P9, P10, P11, P14, P15 |
| 5 | FB | Choke_SMD:Choke_SMD_1206_Handsoldering | L3, L4, L5, L6, L7 |
| 4 | 100uF | SMD_Packages:SMD-1210_Pol | C40, C53, C54, C55 |
| 4 | 10uF | SMD_Packages:SMD-1210_Pol | C37, C41, C42, C43 |
| 4 | 1K | Resistors_SMD:R_1206_HandSoldering | R17, R18, R19, R20 |
| 4 | CONN_02X03 | Pin_Headers:Pin_Header_Straight_2x03 | P16, P17, P18, P19 |
| 4 | JACK_2P | my_lib:RA_3p5_audio_jack | J8, J9, J10, J11 |
| 4 | LED | LEDs:LED_1206 | LED_A1, LED_B1, LED_C1, LED_D1 |
| 3 | 10uF | SMD_Packages:SMD-2010_Pol | C47, C48, C49 |
| 3 | 4504 | SMD_Packages:SO-16-W | U2, U3, U4 |
| 3 | CONN_02X02 | Pin_Headers:Pin_Header_Straight_2x02 | P3, P4, P7 |
| 3 | SMA | minicircuits:SMA_F_RA | J3, J4, J5 |
| 2 | 0.47uH | Choke_SMD:Choke_SMD_1206_Handsoldering | L1, L2 |
| 2 | 100 | Resistors_SMD:R_1206_HandSoldering | R15, R16 |
| 2 | 2R2 | my_lib:RES_10W | R23, R24 |
| 2 | 4R99 | Resistors_SMD:R_1206_HandSoldering | R21, R22 |
| 2 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02 | P12, P13 |
| 2 | CONN_02X08 | Pin_Headers:Pin_Header_Straight_2x08 | P20, P21 |
| 2 | CONN_02X13 | Pin_Headers:Pin_Header_Straight_2x13 | P1, P2 |
| 2 | HEATSINK | my_lib:Heatsink-TO220 | HS2, HS3 |
| 2 | KA278R05 | my_lib:TO-220_4pin_vertical | U8, U9 |
| 2 | PwrPole | my_lib:RA_POWER_POLE | U11, U12 |
| 2 | RELAY_RF | my_lib:RF_RELAY | K1, K2 |
| 1 | 10uF | Capacitors_SMD:C_1210_HandSoldering | C30 |
| 1 | 50 | Resistors_SMD:R_1206_HandSoldering | R14 |
| 1 | 75 | Resistors_SMD:R_1206_HandSoldering | R13 |
| 1 | ADT1.5-1 | minicircuits:ADT1.5-1 | T2 |
| 1 | BARREL_JACK | Connect:BARREL_JACK | CON1 |
| 1 | CONN_01X05 | Pin_Headers:Pin_Header_Straight_1x05 | P5 |
| 1 | CONN_01X07 | Pin_Headers:Pin_Header_Straight_1x07 | P6 |
| 1 | CONN_02X01 | Pin_Headers:Pin_Header_Straight_2x01 | P22 |
| 1 | CY8C4247AXIM | Housings_QFP:LQFP-64_14x14mm_Pitch0.8mm | U1 |
| 1 | DB15 | Connect:DB15FC | J1 |
| 1 | DB25 | Connect:DB25FC | J2 |
| 1 | FUSE | Fuse_Holders_and_Fuses:Fuse_SMD1206_HandSoldering | F1 |
| 1 | KA278R12 | my_lib:TO-220_4pin_vertical | U10 |
| 1 | MAX2611 | TO_SOT_Packages_SMD:SOT-143_Handsoldering | U6 |
| 1 | OPA26741C | SMD_Packages:SOIC-8-N | U7 |
| 1 | SW_PUSH | Buttons_Switches_SMD:SW_SPST_B3S-1000 | SW1 |
| 1 | TC4-LT | minicircuits:TC4-1T | T1 |
| 1 | ULN2003 | SMD_Packages:SO-16-W | U5 |
The 146 most common of 147 parts.
More from ka6s/rp_adapter
1Similar boards
- 2 layers25.5 × 30 mm
- 2 layers28 × 35 mm
- 2 layers90.3 × 74.8 mm
- 6 layers134 × 84.2 mm
- 2 layers83.8 × 48.3 mm
- 2 layers100 × 80 mm
- 2 layers160 × 100.3 mm
Z80-SOUND
dennis9819/Z8C-Homebrew-Computer
To easily develop for my Z80 homebrew system, I designed a simple assempler development environment. This packs the following tasks into one script: zmac assembly object file creation (for xmodem upload) monitor file…
105 parts2 - 2 layers40 × 55.2 mm
NeoGeoController2USB
letoine/NeoGeoControllerToUSB
Simple adapter that transforms a NeoGeo controller into a USB controller.
17 parts2GPL-3.0
Questions
How big is the Temp PCB?
It measures 170.2 × 135.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Temp use?
147 parts, built around the CY8C4247AXI-M485, KA278R05TU, KA278R12CTU and ULN2003. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Temp KiCad files?
From the ka6s/rp_adapter repository on GitHub, at the commit this page was made from: the board is rp_adapter_v5/temp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Temp design in my own project?
Its repository states no licence, so its author keeps all rights: ask ka6s before reusing the design.