Skip to the content
2 layers61.5 × 86.5 mmPico HX711, the printed circuit board in 3D

Program and data for the testing of tensile strength of 3D printed parts

Size
61.5 × 86.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
32
Nets
50
Pads
207
Tracks, vias
147, 15
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
3 Aug 2025
Updated
7 Jun 2026

Overview

Pico HX711 is an open-source printed circuit board by joshcarter, from the joshcarter/tensile_test repository on GitHub, published under the BSD-3-Clause licence. It is a 2-layer board of 61.5 × 86.5 mm with 32 parts on 50 nets, routed with 147 tracks and 15 vias.

It is built around the HX711 and BC807. Its parts include 8 capacitors, 7 connectors, 5 resistors, 3 ICs and 1 transistor. It belongs with the RP2040 boards of this library.

Main components

2

README

README.md

3D Printed Plastic Tensile Strength

Overview

I use this for measuring the tensile strength of 3D printed plastics. There is a test fixture, an interface board, and program that runs on a nearby laptop.

Test Fixture

  • Hi-Lift Jack
  • Two clamps (see printed_parts/Clamp.3mf)
  • 500kg S-type load cell
  • HX711 load cell amplifier
  • Rasperry Pi Pico interface board
  • Laptop with USB connection to interface board

Test Fixture Assembly

TODO: photo and instructions.

Test Samples

See printed_parts/Tensile test samples.3mf. Note that the Z axis has additional cross-sectional area since the Z axis is usually substantially weaker.

Interface Board

  • Sparkfun HX711 load cell amplifier
  • Raspberry Pi Pico

TODO: circuit schematic

The MicroPython code for the Pico is in the pico subdirectory.

Python Requirements

text
pip install -r requirements.txt

Test Fixture Calibration

Initially the fixture will not be calibrated. Load code on the Pi Pico (`pico/*.py) and it will output raw readings from the HX711.

Find some number of known calibration weights. I used kettlebells and used a hanging scale to measure them as accurately as possible. These readings (in KG) go into the CAL_WEIGHTS list in utils.py.

Run the calibration:

text
python tensile_test.py calibrate --port /dev/cu.usbserial101

The first "known weight" should be no weight except the printed clamp. Then add each known weight, pressing enter when the fixture is steady.

Finally, a calibration.json file will be written to this directory. That file should be copied to the Pico. Once the Pico has its calibration file it will output Newtons of force instead of raw HX711 readings.

Running Tensile Tests

The main program is run like so:

text
python tensile_test.py test \
  --port /dev/cu.usbserial101 \
  --type "PETG-CF" \
  --manufacturer "Atomic Filament" \
  --color "black" \
  --axis xy \

All test data will be output to a directory in the data subdirectory, plus summary stats will be collected in data/data.csv.

Parts

32
QtyValueFootprintReferences
6MountingHole_PadMountingHole:MountingHole_2.7mm_M2.5_PadH1, H2, H3, H4, H5, H6
5.1uCapacitor_SMD:C_0603_1608MetricC1, C4, C5, C7, C8
310uCapacitor_SMD:C_1210_3225MetricC2, C3, C6
2100Resistor_SMD:R_0603_1608MetricR4, R5
2Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ6, J7
110kResistor_SMD:R_0603_1608MetricR1
120kResistor_SMD:R_0603_1608MetricR2
13.3uHInductor_SMD:L_0805_2012MetricL1
18.2kResistor_SMD:R_0603_1608MetricR3
1BC807Package_TO_SOT_SMD:SOT-23Q1
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1Conn_01x03MCU_RaspberryPi_and_Boards:Pico_header_3J5
1Conn_01x05Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ1
1Conn_01x20MCU_RaspberryPi_and_Boards:Pico_header_1J3
1Conn_01x20MCU_RaspberryPi_and_Boards:Pico_header_2J4
1HX711Package_SO:SOIC-16_3.9x9.9mm_P1.27mmU2
1LD1117S33TR_SOT223Package_TO_SOT_SMD:SOT-223-3_TabPin2U3
1PicoMCU_RaspberryPi_and_Boards:RPi_Pico_SMD_THU1
1RATEJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1

Similar boards

  • 2 layers114.3 × 102.9 mmTruss PCB, the printed circuit board in 3D

    Truss PCB

    practable/truss

    The truss remote laboratory has been designed for use with Structural Engineering and Engineering Design courses at the University of Edinburgh.

    208 partsAGPL-3.0
  • 2 layers66.3 × 47.8 mmGbwKaffewage, the printed circuit board in 3D

    GbwKaffewage

    staudik/gbwKaffewage

    42 parts
  • 2 layers122.4 × 69.1 mmEvend adapter, the printed circuit board in 3D

    Evend adapter

    temoto/vender

    Open source vending machine controller firmware

    40 parts91CC0-1.0
  • 4 layers129 × 104.6 mmPC-1100X, the printed circuit board in 3D

    PC-1100X

    zscircuits/zs1100a

    All files hardware and software related to the zs1100a

    528 parts76
  • 2 layers55 × 100 mmESP32AY revD2, the printed circuit board in 3D

    ESP32AY revD2

    djspawnbrest/ESP32AY

    ZxPod - ESP32 based AY multiformat player

    138 parts59GPL-3.0
  • 2 layers40 × 24 mmBLDC driver, the printed circuit board in 3D

    BLDC driver

    walmis/BLDC-Servo

    FOC Motor Controller for 57BLF0x NEMA brushless motor

    107 parts43
  • 2 layers89.6 × 79 mmTDR 5351 core, the printed circuit board in 3D

    TDR 5351 core

    MR-DOS/TDR_diploma_thesis

    Time domain reflectometer. Includes Hardware, firmware and GUI in Octave. Also a diploma thesis.

    199 parts33GPL-3.0

Questions

How big is the Pico HX711 PCB?

It measures 61.5 × 86.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pico HX711 use?

32 parts, built around the HX711 and BC807. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pico HX711 KiCad files?

From the joshcarter/tensile_test repository on GitHub, at the commit this page was made from: the board is pcb/Pico-HX711.kicad_pcb and its schematic pcb/Pico-HX711.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pico HX711 design in my own project?

Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).