Skip to the content
2 layers47 × 59.7 mmPcb mainboard, the printed circuit board in 3D

An improvement to arduino_RustysCalling that increases range, responsiveness, battery life, reduces complexity, and even folds your laundry!

Size
47 × 59.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
21
Pads
53
Tracks, vias
87, 0
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
19 Jul 2024
Updated
18 Aug 2024

Overview

Pcb mainboard is an open-source printed circuit board by jonmon6691, from the jonmon6691/arduino_longdistance repository on GitHub, published under the MIT licence. It is a 2-layer board of 47 × 59.7 mm with 12 parts on 21 nets, routed with 87 tracks and 0 vias.

Its parts include 2 resistors, 2 transistors, 2 connectors and 1 diode. It belongs with the computers and single-board computers boards of this library.

README

README.md

arduino_LongDistance

An improvement to arduino_RustysCalling that increases range, responsiveness, battery life, reduces complexity, and even folds your laundry!

Todo

  • Clean up phone wiring, can I get a new handset??
  • Add wiring for dial
  • Power button
    • Toggle button with LED
    • LED can be powered directly with 3.3V output, brightness is good at 2k series R, current is only .5ma

Remote

This module is simply a button and a LoRa transmitter.

While the button is pressed, the remote transmitts packets as fast as it can. Otherwise it's idle, not sending anything.

Note: To maximize the packet rate (and therefore increase the responsiveness), the modems use the .setModemConfig(RH_RF95::Bw500Cr45Sf128) setting to optimize speed at the cost of distance. In practice this results in a packet every 8ms. The range appears to be more than sufficient, even when the rx is closed inside the phone.

Feather Option

https://www.adafruit.com/product/3178

Battery life for a SAMD Radiofruit with a 350mAh little lipo pack is about 1 week. Would be nice if this was replaceable...
Note: that's with 1mA while asleep (not using RFM sleep), 120mA while transmitting

BSN3 Option

https://github.com/EasySensors/ButtonSizeNode3

Programs just like an Arduino Pro Mini, directly with an FTDI cable. Using sleep state for the Mega and for radio its down to 4 microamps. The two CR2032's (255mAh @ 6.5V) should last 7 years!!! I need to double check my ammeter tbh

Phone

The LoRa receiver also orchestrates the phones other functions

Ringer

Every time the phone receives a LoRa packet, it will run the ringer for the next 20 milliseconds. Since the packets come every 8ms, this means the ringer will stay on without interruption while the remote button held down, and will ring for about 20ms after its released. Which isn't noticeable.

To turn on the ringer, the microcontroller drives the gate of an N-channel FET with a 3.3k pulldown resistor. That FET provides a path to ground for a ringer module which converts the DC of a 9V battery into 70V 20Hz AC to power the ringer directly.

  • Experiments on making the ringer louder
    • 2x A23 in parallel,(172mA) Not significantly louder, but less voltage drop during ringing (4v drop vs 2v drop) and will probably last a lot longer
    • 12v wall wart, (210mA) not significantly louder, no voltage drop at all while ringing.
    • 1x 9V, (160mA) not significantly quieter, but could in theory last a lot longer, like 20x
    • 2x A23 in series (24v) doesn't work, but thankfully, doesn't break the ringer either
    • 2x 9V in series (18.5v) doesn't work, but thankfully, doesn't break the ringer either
    • Conclusion: Using single 9V battery for convinience and longevity
  • Power consumption
    • ESP + Lora listening = 81mA! 68mA of that is from the ESP by itself. Surely there's a way to lower this, maybe Wifi or BT is on??
    • Audio FX board: 29mA idle

Playing audio

When the handset is lifted off the cradle, the phone will play a random audio file through the speaker.

The audio is generated by an Adafruit SFX board which is controlled using UART from the LoRa receiver module.

When the handset is placed back on the cradle, the audio will stop.

When the dial is turned and the handset is off the cradle, the current audio will be interrupted and the phone will play a giggling noise. When it's released, it will start a new audio.

The ground of the audio board is driven with another FET like the ringer module so that the power consumption can be cut by the main controller.

Parts

12
QtyValueFootprintReferences
23.3kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1, R2
2Q_NMOS_GSDPackage_TO_SOT_THT:TO-251-3-1EP_Horizontal_TabDownQ1, Q2
19VConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical9V1
1Adafruit_Audio_FX_+_Ampld_components:Adafruit Audio FX + AmpA1
1Adafruit_Feather_M0_RFM9x_LoRa_Radiold_components:Adafruit_Feather_M0_RFMA2
1D_SchottkyDiode_THT:D_DO-41_SOD81_P7.62mm_HorizontalD1
1LOGOLOGOG***
1LOGOld_components:rustyG***
1Phone BodyConnector_PinSocket_2.54mm:PinSocket_2x04_P2.54mm_VerticalJ2
1Ringer ModuleConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ1

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the Pcb mainboard PCB?

It measures 47 × 59.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pcb mainboard use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pcb mainboard KiCad files?

From the jonmon6691/arduino_longdistance repository on GitHub, at the commit this page was made from: the board is pcb_mainboard/pcb_mainboard.kicad_pcb and its schematic pcb_mainboard/pcb_mainboard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pcb mainboard design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).