
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

A PCB for is designed for use with the 'ESP32 Zero' boards and 1-Wire sensors.
ESP32C6 Temp Sensor is an open-source printed circuit board by jonathanadams, from the jonathanadams/pcb-esp32-zero-1-wire repository on GitHub. It is a 2-layer board of 42 × 31 mm with 11 parts on 20 nets, routed with 62 tracks and 5 vias.
It is built around the DS18B20. Its parts include 7 ICs, 2 resistors and 1 diode. It belongs with the sensors and measurement boards and the ESP32 and RISC-V boards of this library.
This PCB for is designed for use with the 'ESP32 Zero' boards such as Waveshare ESP32-C6-Zero or Waveshare ESP32-C3-Zero and 1-Wire sensors. You can hook up any 1-Wire sensors but it was primarialy designed to be used with Dallas DS18B20 temperature sensors.

| Ref | Qty | Description/Value | Notes |
|---|---|---|---|
| U1 | 1 | ESP32-C3-Zero or ESP32-C6-Zero | |
| U2-U7 | 6 | KF128 2.54mm Pitch 3P Screw Terminal | |
| R1 | 1 | 0805/2012 SMD Resistor (4.7k Ohm) | |
| R2 | 1 | 0805/2012 SMD Resistor (75 Ohm) | Check D1 LED Requirements |
| D1 | 1 | 0805/2012 SMD LED | Check R2 Resistor Requirements |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | DS18B20 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-3P_1x03_P2.54mm_Horizontal | U2, U3, U4, U5, U6, U7 |
| 1 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 75 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_Pad1.0x1.5mm_NumberLabels | JP1 |
| 1 | ~ | Waveshare-ESP32:Waveshare-ESP32-C6-Zero | U1 |

UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

pablozg/freeds
Derivador de energía solar excedente creado por Pablo Zerón, Diseño PCB por Amcalo, Tester original por Aeizoon, Wiki por Zoilo Mora

AK-Homberger/NMEA2000WifiGateway-with-ESP32
This repository shows how to build a NMEA2000 WiFi Gateway with voltage and temperature alarms.

fehlfarbe/arduino-motorfocus
Arduino motorfocus with moonlite protocol for telescopes



felixwittwer/homeassistant_automaic_greenhouse
A cool Project to make your greenhouse smart. What about automaic irrigation and collecting enviromental data right from your garden.

Neumi/fastLOGIC
An affordable Arduino-based board designed for straightforward (industrial) logic control, ideal for building small-scale automation and control solutions.
It measures 42 × 31 mm and has 2 copper layers, 1.6 mm thick.
11 parts, built around the DS18B20. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jonathanadams/pcb-esp32-zero-1-wire repository on GitHub, at the commit this page was made from: the board is kicad/ESP32C6 Temp Sensor.kicad_pcb and its schematic kicad/ESP32C6 Temp Sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask jonathanadams before reusing the design.