4 layers110 × 46 mm
4 layers58 × 58 mm
Bebop
jonasblixt/bebop7Power-over-ethernet BLE bridge
- Size
- 58 × 58 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 245
- Nets
- 326
- Pads
- 1,184
- Tracks, vias
- 3,288, 677
- Pours
- 41
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Apr 2019
- Updated
- 8 Dec 2019
Overview
Bebop is an open-source printed circuit board by jonasblixt, from the jonasblixt/bebop repository on GitHub. It is a 4-layer board of 58 × 58 mm with 245 parts on 326 nets, routed with 3,288 tracks and 677 vias.
It is built around the MCIMX6G2AVM07AB, FEMC004GTTE7-T13-17 and MIC23150-55YMT-TR, with the MIC23150-SYMT-TR, USBLC6-4 and LP3470M5-3.08 among its other parts. Its parts include 128 capacitors, 56 resistors, 14 ICs, 6 diodes and 6 inductors. It belongs with the interfaces and adapters boards of this library.
Main components
12
MCIMX6G2AVM07AB
LFBGA-289-40℃~+105℃ 12bit 696MHz ARM Cortex-A7 LFBGA-289 Microcontrollers (MCU/MPU/SOC) ROHSNXP SemiconductorsMicrocontrollers (MCU/MPU/SOC)FEMC004GTTE7-T13-17
FBGA-100(14x18)ECC error correction function、Software write protection function、Power lock protection function、Hardware encryption function FBGA-100(14x18) NAND FLASH ROHSFlexxonNAND FLASH
MIC23150-55YMT-TR
TDFN-8(2x2)-40℃~+125℃@(TJ) 1 1.35V 2.7V~5.5V 2A 4MHz Buck Buck Built-in Fixed Yes TDFN-8(2x2) DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersMIC23150-SYMT-TR
TDFN-8(2x2)-40℃~+125℃@(TJ) 1 2.7V~5.5V 2A 3.3V 4MHz Buck Buck Built-in Fixed Yes TDFN-8(2x2) DC-DC Converters ROHSMicrochip TechnologyDC-DC ConvertersUSBLC6-4
UncategorisedSTMicroelectronics
LP3470M5-3.08
SOT-23-5-20℃~+85℃@(Ta) 1 2ms 3.08V 500mV~5.5V Active Low No No Open Drain Voltage Monitor SOT-23-5 Supervisor and Reset ICs ROHSTexas InstrumentsSupervisor And Reset ICs
LTC4267IDHC#PBF
DFN-16-EP(3x5)-40℃~+85℃ 8.7V~9.2V Under-voltage lockout (UVLO) DFN-16-EP(3x5) Power Over Ethernet (PoE) Controllers ROHSAnalog DevicesEthernet ICs
MT41K512M16HA-125:A
FBGA-960℃~+95℃ 1.283V~1.45V 800MHz 8Gbit Auto precharge function、Data mask function、Dynamic on-chip termination、ZQ calibration function、Asynchronous reset function、Write leveling function、Auto self-refresh DDR3L SDRAM FBGA-96 DDR SDRAM ROHSMicron TechDDR SDRAM
FTSH-105-01-F-DV-K
SMD,P=1.27mm-55℃~+125℃ 1.27mm 10P 2 2x5P 3.05mm 3.4A Black Gold Phosphor bronze Pin Header Surface Mount,Vertical SMD,P=1.27mm Pin Headers ROHSSamtecPin Headers
KMR631NGULCLFS
SMD-40℃~+85℃ 1.9mm 2.8mm 32V 3N 4.6mm 50mA Gull Wing IP67 Round Button SPST Surface Mount,Vertical SMD Tactile Switches ROHSC&KTactile Switches
MMBTA42
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mV 300V 350mW 500mA 50MHz 5V NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
NX2520SA-24.000000MHZ
SMD2520-4P-10℃~+70℃ 10pF 24MHz 60Ω ±10ppm ±10ppm SMD2520-4P Crystals ROHSNDKCrystals
README
README.mdbebop
Power-over-ethernet BLE bridge. This is a work in progress.
Parts
245| Qty | Value | Footprint | References |
|---|---|---|---|
| 81 | C0402_1u_10Vdc_X5R | Capacitors_SMD:C_0402 | C1, C10, C11, C12, C13, C14, C15, C17, C101, C103, C104, C105, C109, C110, C124, C127 +65 |
| 13 | R0402_46k40 | Resistors_SMD:R_0402 | R3, R4, R18, R19, R21, R22, R24, R25, R26, R27, R28, R29, R53 |
| 7 | C0603_10u_10Vdc_X7R | Capacitors_SMD:C_0603 | C63, C64, C66, C71, C91, C102, C123 |
| 6 | C0402_15p_100Vdc_C0G | Capacitors_SMD:C_0402 | C72, C73, C74, C75, C125, C126 |
| 6 | C0603_22u_10Vdc_X5R | Capacitors_SMD:C_0603 | C7, C22, C23, C25, C31, C45 |
| 5 | R0402_100R | Resistors_SMD:R_0402 | R1, R2, R9, R16, R17 |
| 5 | R0402_10k | R_0402 | R6, R7, R37, R47, R48 |
| 4 | MHNP_2.5mm | Jonas:MH_2.5mm | M1, M2, M3, M4 |
| 4 | R0402_100k | Resistors_SMD:R_0402 | R13, R14, R15, R67 |
| 4 | R0402_10k | Resistors_SMD:R_0402 | R12, R30, R33, R40 |
| 4 | R0402_1k50 | Resistors_SMD:R_0402 | R31, R32, R49, R50 |
| 4 | R0603_49R90 | Resistors_SMD:R_0603 | R36, R39, R41, R42 |
| 3 | BAS516,135 | Diodes_SMD:D_SOD-523 | D3, D4, D5 |
| 3 | TP | footprints:TP_1mm | TP1, TP2, TP3 |
| 2 | BL0603_BLM18KG121TN1D | Resistors_SMD:R_0603 | FB1, FB2 |
| 2 | C0402_0p8_50Vdc_C0G_3 | Capacitors_SMD:C_0402 | C132, C133 |
| 2 | C0402_100p_25Vdc_C0G | Capacitors_SMD:C_0402 | C128, C129 |
| 2 | C0402_10n_50Vdc_X7R | Capacitors_SMD:C_0402 | C68, C69 |
| 2 | C0603_1u_25Vdc_X7R | Capacitors_SMD:C_0603 | C89, C90 |
| 2 | C1206_100u_6.3Vdc_X5R | Capacitors_SMD:C_1206 | C119, C122 |
| 2 | C1206_1n5_1000Vdc_X7R | Capacitors_SMD:C_1206 | C112, C113 |
| 2 | C1210_1u_100Vdc_X7R | Capacitors_SMD:C_1210 | C106, C107 |
| 2 | FTSH-105-01-F-DV-K | Jonas:FTSH-105-01-F-DV-K | J3, J4 |
| 2 | IHLP1212_1u_1 | IHLP1212 | L1, L3 |
| 2 | KMR631NGULCLFS | Jonas:kmr6 | PB1, PB2 |
| 2 | R0402_10k | Jonas:R_0402 | R45, R46 |
| 2 | R0402_240R | Resistors_SMD:R_0402 | R5, R8 |
| 2 | R0402_330R | Resistors_SMD:R_0402 | R34, R38 |
| 2 | R0603_100k | Resistors_SMD:R_0603 | R54, R65 |
| 2 | R0603_220k | Resistors_SMD:R_0603 | R55, R57 |
| 2 | USBLC6-4 | TO_SOT_Packages_SMD:SOT-23-6 | U7, U12 |
| 1 | 1051330011 | Jonas:1051330011 | J1 |
| 1 | 2N7002 | TO_SOT_Packages_SMD:SOT-23 | Q4 |
| 1 | 7499210123 | footprints:7499210123 | J2 |
| 1 | BAT54C-7-F | TO_SOT_Packages_SMD:SOT-23 | D7 |
| 1 | BZX84C8V2LT1G | TO_SOT_Packages_SMD:SOT-23 | D2 |
| 1 | C0402_0p8_25Vdc_C0G_5 | Capacitors_SMD:C_0402 | C131 |
| 1 | C0402_100n_100Vdc_X5R | Capacitors_SMD:C_0402 | C67 |
| 1 | C0402_100n_10Vdc_X7R | Capacitors_SMD:C_0402 | C130 |
| 1 | C0603_1u_10Vdc_X7R | Capacitors_SMD:C_0603 | C116 |
| 1 | C0603_27n_16Vdc_X7R | Capacitors_SMD:C_0603 | C121 |
| 1 | C0603_33n_16Vdc_X7R | Capacitors_SMD:C_0603 | C118 |
| 1 | C0603_470p_100Vdc_X7R | Capacitors_SMD:C_0603 | C120 |
| 1 | C0603_4u7_10Vdc_X7R | Capacitors_SMD:C_0603 | C111 |
| 1 | C0603_68p_200Vdc_X7R | Capacitors_SMD:C_0603 | C114 |
| 1 | C0805_10u_25Vdc_X7R | Capacitors_SMD:C_0805 | C92 |
| 1 | C0805_20n_50Vdc_X7R | Capacitors_SMD:C_0805 | C108 |
| 1 | C1812_2n2_250Vac_X7R | Capacitors_SMD:C_1812 | C115 |
| 1 | FEMC004GTTE7-T13-17 | Jonas:100LBGA_DQ | U6 |
| 1 | IHLP1212_3u3_a5 | IHLP1212 | L2 |
| 1 | IHLP2020_3u3_13 | footprints:IHLP2020 | L4 |
| 1 | LAN8710 | Jonas:QFN-32-1EP_5x5mm_Pitch0.5mm | U11 |
| 1 | LP3470M5-3.08 | TO_SOT_Packages_SMD:SOT-23-5 | U3 |
| 1 | LQG15HN_2n7 | Inductors_SMD:L_0402 | L6 |
| 1 | LQG15HN_3n9 | Inductors_SMD:L_0402 | L5 |
| 1 | LTC3447 | Housings_DFN_QFN:DFN-10-1EP_3x3mm_Pitch0.5mm | U5 |
| 1 | LTC4267IDHC | Jonas:DHC16 | U15 |
| 1 | MCIMX6G2AVM07 | Jonas:LFBGA289 | U1 |
| 1 | MIC23150-55YMT | Housings_DFN_QFN:DFN-8_2x2mm_Pitch0.5mm | U13 |
| 1 | MIC23150-SYMT | Housings_DFN_QFN:DFN-8_2x2mm_Pitch0.5mm | U4 |
| 1 | MMBTA42 | TO_SOT_Packages_SMD:SOT-23 | Q3 |
| 1 | MT41K512M16HA-125 | Jonas:BGA-96_pitch0.8mm_dia0.4mm | U2 |
| 1 | NCP360SNAET1G | TO_SOT_Packages_SMD:SOT-23-5 | U8 |
| 1 | NCV551SN33T1G | TO_SOT_Packages_SMD:SOT-23-5 | U14 |
| 1 | NX2012SA-32.768K-STD-MUB-1 | Jonas:NX2012 | X1 |
| 1 | NX2520SA-24.000000MHZ | footprints:NX2520 | X2 |
| 1 | NX2520SA-32.000000MHZ | footprints:NX2520 | X3 |
| 1 | P6SMB540A_E3_52 | Diodes_SMD:SMB_Standard | D6 |
| 1 | PCAP_220u_15 | Capacitors_SMD:c_elec_6.3x7.7 | C2 |
| 1 | PCAP_220u_15 | Capacitors_SMD:CP_Elec_8x5.4 | C117 |
| 1 | POE60F-50L_ | Jonas:POE60F | T1 |
| 1 | PRO-OB-440 | footprints:PRO-OB-440 | Z1 |
| 1 | PS2911-1e | Jonas:PS2911 | U16 |
| 1 | R0402_12k10 | Resistors_SMD:R_0402 | R35 |
| 1 | R0402_22R | Resistors_SMD:R_0402 | R23 |
| 1 | R0402_2M20 | Resistors_SMD:R_0402 | R20 |
| 1 | R0402_46k40 | Jonas:R_0402 | R68 |
| 1 | R0603_10R | Resistors_SMD:R_0603 | R62 |
| 1 | R0603_10k | Resistors_SMD:R_0603 | R43 |
| 1 | R0603_1k | Resistors_SMD:R_0603 | R61 |
The 232 most common of 245 parts.
Questions
How big is the Bebop PCB?
It measures 58 × 58 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Bebop use?
245 parts, built around the MCIMX6G2AVM07AB, FEMC004GTTE7-T13-17, MIC23150-55YMT-TR and MIC23150-SYMT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bebop KiCad files?
From the jonasblixt/bebop repository on GitHub, at the commit this page was made from: the board is hw/design/bebop.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bebop design in my own project?
Its repository states no licence, so its author keeps all rights: ask jonasblixt before reusing the design.
Similar boards
- 4 layers58 × 18 mm
- 4 layers70.6 × 42 mm
Base raw
Alli-Ekundayo/scpt-rl
SCPT-RL trains a cross-attention transformer policy to place PCB components sequentially on a discrete grid. Training has two phases:
165 partsMIT - 2 layers141 × 68.6 mm
- 4 layers54.4 × 53.3 mm
- 2 layers10.2 × 7.6 mm
- 4 layers58 × 104 mm
- 2 layers150 × 90 mm
ECE445L Lab7Restart
Andres-Wearden/Lab10
The typical explanation for the repo structure. Lab specific instructions can be found further below.
87 parts