

Battery reg module fet
Custom lithium-polymer battery voltage monitor and regulator module (N-FET version)
- Size
- 15.2 × 12.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 13
- Nets
- 8
- Pads
- 29
- Tracks, vias
- 103, 8
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 Jan 2024
- Updated
- 13 Apr 2025
Overview
Battery reg module fet is an open-source printed circuit board by johnmgreenwell, from the johnmgreenwell/battery-reg-module-fet repository on GitHub, published under the MIT licence. It is a 2-layer board of 15.2 × 12.7 mm with 13 parts on 8 nets, routed with 103 tracks and 8 vias.
Its parts include 5 resistors, 2 capacitors, 2 ICs, 2 connectors and 1 transistor. It belongs with the power boards of this library.
README
README.mdBattery Regulator Module (N-FET Version)
Custom lithium-polymer battery voltage monitor and regulator module (N-FET version).
Overview
This custom module is designed as a drop-in for small-scale electronics projects providing 3.3V linear regulated voltage output from a raw lithium polymer cell input. The battery input voltage is monitored by the MIC2779 whose output enables or disables the regulated output supply. It is configured with hysteresis to cutoff output when the battery voltage reaches 3.1V and to then hold in reset until the battery voltage exceeds 3.6V.
This is a form-factor-compatible replacement for the battery regulator module design available here. This version makes use of an N-FET transistor for switching rather than the built-in enable used in the original design. This version is meant to serve as a alternate to be used on the basis of parts-available.

The module supports the 1.5A maximum current limitations of the regulator chip AP7363 used.
This module may be combined with a Lipo charger module such as the TP4056 (along with any in-circuit charging mods as required) for a complete custom battery charging/monitoring/regulation for small-scale electronics projects.
The zipped gerber files provided may be uploaded to a PCB manufacturer for fabrication. Below is the automatic rendering of the uploaded gerbers by OSHPark.

Schematic
The schematic for the circuit is provided below as designed in Kicad 9.

License
MIT © 2024 John Greenwell
Parts
13| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J2 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4 |
| 1 | 340k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 56k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 604k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | AP7363-18D-13 | Footprints:TO252__DPAK__1 | IC1 |
| 1 | MIC2779H-1YM5-TR | Footprints:SOT-23-5_M5_MCH-L | U1 |
| 1 | NMOS | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1 |
The 12 most common of 13 parts.
Similar boards
- 2 layers40 × 20 mm

- 2 layers74.9 × 49.5 mm

- 2 layers35 × 29 mm

MagSpoofTC
samyk/magspoof
A portable device that can spoof/emulate any magnetic stripe, credit card or hotel card "wirelessly", even on standard magstripe (non-NFC/RFID) readers.
13 parts4.2k - 2 layers20.6 × 23.6 mm

AO-03 signal amplifier
fossasia/pslab-scripts
Pocket Science Lab - Scripts for Sensor Experiments
13 parts1.6kApache-2.0 - 2 layers47 × 35.6 mm

- 2 layers95 × 95 mm

Cube batteryboard
willem-pennings/balancing-cube
A cube that balances itself in a corner or edge using reaction wheels
13 parts1.1kGPL-3.0 - 2 layers15.2 × 20.3 mm

Pt100stick
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group
13 parts1.1kGPL-3.0 - 2 layers53.9 × 23.2 mm

Buffer
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
13 parts1kGPL-3.0
Questions
How big is the Battery reg module fet PCB?
It measures 15.2 × 12.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Battery reg module fet use?
13 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Battery reg module fet KiCad files?
From the johnmgreenwell/battery-reg-module-fet repository on GitHub, at the commit this page was made from: the board is battery-reg-module-fet.kicad_pcb and its schematic battery-reg-module-fet.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Battery reg module fet design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).