Skip to the content
2 layers124.4 × 85.9 mmPcb raven split-38key choc hotswap n!n, the printed circuit board in 3D

Pcb raven split-38key choc hotswap n!n

joelove/rvkbd2

Raven wireless split keyboard design files 🐦‍⬛

Size
124.4 × 85.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
48
Nets
42
Pads
374
Tracks, vias
514, 57
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
22 Oct 2023
Updated
27 May 2025

Overview

Pcb raven split-38key choc hotswap n!n is an open-source printed circuit board by joelove, from the joelove/rvkbd repository on GitHub. It is a 2-layer board of 124.4 × 85.9 mm with 48 parts on 42 nets, routed with 514 tracks and 57 vias.

Its parts include 19 diodes, 19 switches and 1 IC. It belongs with the keyboards and input boards and the AVR (ATmega, ATtiny) boards of this library.

README

README.md

Raven Split Keyboard

Sponsor

PCB Preview

The Raven keyboard (rvkbd) is a wireless, low-profile, split keyboard based on the Corne keyboard by foostan. It has a 3x5 column staggered layout with 3 thumb keys and 1 extra outer pinky key.

The goal of this project is to create a split layout with an aggressive, irregular stagger to match a sub-integer 2D:4D ratio of approximately 0.925. The 38-key layout is a product of countless iterations on my personal keymap, aiming to minimize finger movement and total keystrokes whilst maintaining a clean, logical distinction between layers.

🛠️ Version 1 Build Guide 🛠️

Wiring Diagram

Example Keymap

Example Keymap

Microcontrollers

The Raven is designed to be entirely wireless and built with the nice!nano microcontroller. A full list of international stockists is available on their website.

The keyboard is compatible with any wireless controller with a Pro Micro footprint. One of the best-received and easiest to obtain nice!nano clones is the Supermini NRF5284 which has been tested with this keyboard and works as expected.

A comprehensive list of possible alternatives can be found here. Most of these options are untested and you might run into unforeseen complexities when using an alternative microcontroller.

Keycaps

The PCB key-spacing is designed for 17x17mm keycaps with a 2mm border radius. I've read that standard Kailh keycaps are 17x18mm so will probably not fit without modification.

The keyboard works best with Chosfox PBT keycaps which can be purchased from the Mechanical Switch Store on AliExpress and shipped internationally. They also sell homing keys and 1.5U thumb keys here.

Plate

Version 1 comes with an edge-cuts gerber intended to be cut from 1.2mm FR-4. Alternatively, an identical but untested DXF is included for lazer cutting other sheet materials.

The plate should be exactly 1.2mm thick and fairly stiff to allow the low profile choc (v1) switches to attach easily and securely. The switches will slip out of a thicker plate more easily but the edges of the plate cuts are quite thin so the material needs to be very strong and not too brittle, e.g. carbon fibre or aluminum.

Case

Version 1 is not intended to be used with a case and does not include a case model of any kind nor the required mounting holes. Instead, the board rests directly on the hotswap sockets and uses rubber feet for grip and stability. This is an intentional decision intended to reduce the height of the board but probably reduces the durability of the final product.

If you want to use a case, I recommend adding several through-hole pads to the PCB file before having it fabricated. How you use those mounting holes and create the case itself is up to you. Common approaches include 3D-printing and making a layered case out of extra unprinted FR-4 or other lazer cut sheet materials.

Firmware

The Raven uses ZMK for firmware. Because the PCB shares a wiring schematic with the Corne keyboard, it can be loaded with any existing 3x6 Corne configuration.

Any repurposed Corne 3x6 keymap will be missing the outermost top and bottom keys due to the difference in physical layout. Any key mappings in these positions will not be accessible on the Raven.

If you want to customize the layout or create your own config, I have created a custom shield and config repo. Just fork the repo and use the layout editor in the README to quickly and easily design your own.

Flashable firmware artifacts can be found in the repo Actions tab, just download them then hit the reset key twice on each half and drag each firmware file onto the "NICENANO" drive that appears.

Parts

48
QtyValueFootprintReferences
19Dkbd:D3_SMDD2, D3, D4, D5, D6, D10, D11, D12, D14, D15, D16, D17, D18, D19, D20, D21 +3
18SW_PUSHkbd:Choc_HotswapSW2, SW3, SW4, SW5, SW6, SW7, SW10, SW11, SW12, SW14, SW15, SW16, SW17, SW18, SW19, SW20 +2
2LOGOLOGOG***, G***
2MountingHole_2.2mm_M2_PadMountingHole:MountingHole_2.2mm_M2_PadM2_0, M2_1
2MountingHole_Padkbd:1pin_connBat+, GND
2SW_SPDTKailh:SPDT_C128955SW_POWER, SW_POWER
1ProMicrokbd:ProMicro_v2U1
1Resetkbd:ResetSWRSW1
1SW_PUSHkbd:Choc_Hotswap_1.5uSW21

Similar boards

  • 2 layersDemo, the printed circuit board in 3D

    Demo

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    48 parts547GPL-3.0
  • 2 layers18.8 × 18.1 mmAmoeba royale, the printed circuit board in 3D

    Amoeba royale

    mtl/keyboard-pcbs

    Keyboard PCBs

    48 parts485
  • 2 layers48.1 × 115.6 mmAPU ENG CRANK PANEL, the printed circuit board in 3D

    APU ENG CRANK PANEL

    jrsteensen/OpenHornet

    OpenHornet 1:1 F/A-18C Simulator Repository

    48 parts431
  • 2 layers106 × 55 mmEndcap, the printed circuit board in 3D

    Endcap

    softerhardware/Hermes-Lite2

    A second generation low-cost amateur HF software defined radio transceiver.

    48 parts384
  • 2 layers42.8 × 88 mm18650 pcb, the printed circuit board in 3D

    18650 pcb

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    48 parts253GPL-3.0
  • 2 layers34 × 44 mmClk lo buffer, the printed circuit board in 3D

    Clk lo buffer

    loxodes/vna

    Under development open hardware microwave vector network analyzer

    48 parts205
  • 2 layers70.6 × 189.2 mmNano, the printed circuit board in 3D

    Nano

    fellesverkstedet/fabricatable-machines

    Motion systems for flexible digital fabrication and research. Easy to fabricate and customize. Documentation: https://github.com/fellesverkstedet/fabricatable-machines/wiki

    48 parts175

Questions

How big is the Pcb raven split-38key choc hotswap n!n PCB?

It measures 124.4 × 85.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Pcb raven split-38key choc hotswap n!n use?

48 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Pcb raven split-38key choc hotswap n!n KiCad files?

From the joelove/rvkbd repository on GitHub, at the commit this page was made from: the board is raven-split-38key/raven-split-38key__choc-hotswap-n!n/pcb/pcb__raven-split-38key__choc-hotswap-n!n.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Pcb raven split-38key choc hotswap n!n design in my own project?

Its repository states no licence, so its author keeps all rights: ask joelove before reusing the design.