

MACK10 Controller
Mini Tensile Tester Project
- Size
- 57.3 × 67.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 62
- Nets
- 62
- Pads
- 241
- Tracks, vias
- 851, 154
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 17 Jul 2026
- Updated
- 28 Sep 2026
Overview
MACK10 Controller is an open-source printed circuit board by joehanko, from the joehanko/MACK-10 repository on GitHub. It is a 2-layer board of 57.3 × 67.1 mm with 62 parts on 62 nets, routed with 851 tracks and 154 vias.
It is built around the HX711, PCF8575DB and TMC2208-LA, with the SS14 and SS8550 among its other parts. Its parts include 13 resistors, 9 connectors, 8 capacitors, 6 ICs and 3 diodes.
Main components
5HX711
SOP-16-40℃~+85℃ 1.4mA 10Hz、80Hz 1MHz~20MHz、11.0592MHz 2 2.6V~5.5V 20mV、40mV、80mV 24 Built-in External、Built-in SPI Support Yes SOP-16 Analog to Digital Converters (ADC) ROHSAvia SemiconAnalog To Digital Converters (ADC)PCF8575DB
SSOP-24-208mil-40℃~+85℃ 16 2.5V~5.5V 200uA 25mA 300uA 400kHz 8 I2C、SMBus Interrupt Output Open-drain Reset function、Cascading and address extension、Built-in LED driver SSOP-24-208mil I/O Expanders ROHSTexas InstrumentsI/O ExpandersTMC2208-LA
QFN-28(5x5)1.4A 256 3.3V~5V 570mΩ Bipolar Driver Overcurrent Protection、Short-Circuit Protection、Over temperature protection、Under-voltage lockout、Motor step-out prevention function、Built-in charge pump STEP/DIR、UART Yes QFN-28(5x5) Stepper Motor Driver ROHSTRINAMIC Motion Control GmbHStepper Motor DriverSS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesSS8550
SOT-23-55℃~+150℃ 1 PNP 1.5A 100MHz 100nA 120 25V 300mW 500mV 5V PNP SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
README
README.mdMACK-10 Tensile Tester
An open-source desktop tensile tester for affordable material characterization and education.
Overview
MACK-10 is an open-source desktop tensile tester designed to measure the force and displacement of small material specimens.
The project combines an ESP32-based controller, load cell, stepper-driven linear stage, custom PCB, and 3D-printed components to create a low-cost alternative to commercial material testing equipment.
The target capacity is 10 kg (~98 N), making MACK-10 suitable for testing:
- 3D-printed plastics
- Engineering polymers
- Composites
- Thin metals
- Educational material samples
Current Status
🚧 Prototype Development — Revision 1
Electronics
- Custom KiCad controller PCB
- ESP32 controller
- HX711 load cell interface
- TMC2208 stepper driver
- LM2596 power regulation
- OLED interface
- E-stop input
- Dual limit switch inputs
- PlatformIO firmware
- Automatic taring
- Peak force tracking
- Break detection
- Live serial plotting
Mechanical
- 200 mm T6×1 linear motion stage
- NEMA 11 stepper drive
- Structural frame
- Load cell mount
- Specimen grips
- Electronics enclosure
In Development
- Load cell calibration
- Crosshead speed control
- Position tracking
- Force-displacement logging
- Stress-strain calculations
- CSV export
Target Specifications
| Specification | Target |
|---|---|
| Maximum Force | 10 kg (~98 N) |
| Load Cell | 10 kg S-Type |
| Controller | ESP32 |
| Motion | NEMA 11 + T6×1 Lead Screw |
| Travel | 200 mm |
| User Interface | 128×64 OLED |
| PCB | Custom KiCad Design |
| Firmware | PlatformIO |
Bill of Materials
Electronics
| Qty | Component | Approx. Cost | Line Total |
|---|---|---|---|
| 1 | ESP32 DevKit V1 | $8.00 | $8.00 |
| 1 | Custom MACK-10 Controller PCB | $1.08 | $1.08 |
| 1 | HX711 Load Cell Amplifier | $3.00 | $3.00 |
| 1 | TMC2208 Stepper Driver | $5.00 | $5.00 |
| 1 | LM2596 Buck Converter | $2.00 | $2.00 |
| 1 | 10 kg S-Type Load Cell | $25.00 | $25.00 |
| 1 | SSD1306 128×64 OLED | $5.00 | $5.00 |
| 1 | PCB Fuse Holder | $1.00 | $1.00 |
| 1 | 2–2.5 A Fuse | $0.50 | $0.50 |
| 1 | Power Switch | $3.00 | $3.00 |
| 1 | Emergency Stop Switch | $12.00 | $12.00 |
| 2 | Limit Switches | $2.00 | $4.00 |
| 1 Set | JST-XH Connectors & Crimps | $4.00 | $4.00 |
| 1 Set | Female Header Sockets | $2.00 | $2.00 |
| — | LEDs, Resistors & Capacitors | ~$2.00 | ~$2.00 |
| — | Wire, Heat Shrink & Misc. | ~$5.00 | ~$5.00 |
Estimated Electronics Cost: ~$83
Mechanical
| Qty | Component | Approx. Cost | Line Total |
|---|---|---|---|
| 1 | T6×1 Linear Motion Stage, 200 mm | $31.99 | $31.99 |
| 1 | NEMA 11 Stepper Motor | Included | Included |
| 1 | T6×1 Lead Screw | Included | Included |
| 1 | Linear Guide & Carriage | Included | Included |
| 1 | Structural Frame Hardware | ~$20.00 | ~$20.00 |
| 1 | Grip Hardware | ~$20.00 | ~$20.00 |
| 1 | M3 Fastener Kit | ~$10.00 | ~$10.00 |
| 1 | M3 Heat-Set Inserts | ~$5.00 | ~$5.00 |
| — | Filament | ~$20.00 | ~$20.00 |
Estimated Mechanical Cost: ~$107
Current Estimated Build Cost: ~$190 + power supply and miscellaneous hardware
Repository Structure
firmware/ ESP32 firmware
pcb/ KiCad project files
cad/ Mechanical CAD models
docs/ Documentation
images/ Project photos and diagramsRoadmap
Revision 1
Complete the mechanical assembly, calibrate the load cell, and perform initial tensile tests.
Revision 2
Optimize the PCB, wiring, enclosure, motion control, and data acquisition.
Revision 3
Add automated testing, material property calculations, and desktop software.
Disclaimer
MACK-10 is intended for educational and hobby use and is not a replacement for calibrated or certified laboratory testing equipment.
Measurements should not be used for engineering certification, regulatory compliance, or safety-critical design decisions.
Project Status: Active Development 🚧
Parts
62| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C1, C4, C6, C8 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R8, R9, R10, R13 |
| 4 | MountingHole_3.2mm_M3_Pad_Via | MountingHole:MountingHole_3.2mm_M3_Pad_Via | Mount 1, Mount 2, Mount 3, Mount 4 |
| 3 | GND | TestPoint:TestPoint_Pad_2.0x2.0mm | TP11, TP11, TP11 |
| 2 | 100 | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric | R6, R7 |
| 2 | 3V3 | TestPoint:TestPoint_Pad_2.0x2.0mm | TP8, TP8 |
| 2 | 4.7k, DNP | Resistor_SMD:R_0805_2012Metric | R11, R12 |
| 2 | 5VOUT | TestPoint:TestPoint_Pad_2.0x2.0mm | TP10, TP10 |
| 1 | 100nF 50V | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 100uF 35V | Capacitor_SMD:CP_Elec_6.3x7.7 | C7 |
| 1 | 18k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 24V | TestPoint:TestPoint_Pad_2.0x2.0mm | TP9 |
| 1 | 24V IN | Connector_BarrelJack:BarrelJack_CUI_PJ-102AH_Horizontal | J9 |
| 1 | 470 | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | 7.5k | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | BYP_1 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | BYP_2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J10 |
| 1 | E_STOP | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J8 |
| 1 | Fan | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | Fuse | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | F1 |
| 1 | HX711 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | HX_DT | TestPoint:TestPoint_Pad_2.0x2.0mm | TP2 |
| 1 | HX_SCK | TestPoint:TestPoint_Pad_2.0x2.0mm | TP3 |
| 1 | I/O | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
| 1 | INA226 | MACK10:INA226 | U4 |
| 1 | Interface IDC | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J6 |
| 1 | J_Expansion | Connector_PinHeader_2.54mm:PinHeader_2x07_P2.54mm_Vertical | J3 |
| 1 | M24V | TestPoint:TestPoint_Pad_2.0x2.0mm | TP7 |
| 1 | MINI360 | Mini360:Mini360_step-down | U6 |
| 1 | Motor | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J2 |
| 1 | PCF8575 | MACK10:PCF8575 | U5 |
| 1 | POWER | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | SCL | TestPoint:TestPoint_Pad_2.0x2.0mm | TP5 |
| 1 | SDA | TestPoint:TestPoint_Pad_2.0x2.0mm | TP4 |
| 1 | SS14 | Diode_SMD:D_SMA | D3 |
| 1 | SS8550 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | STATUS | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | STEP | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1 |
| 1 | Sensor IDC | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J5 |
| 1 | TMC2208 | MACK10:TMC2208_STEPSTICK | U1 |
| 1 | VMOT | TestPoint:TestPoint_Pad_2.0x2.0mm | TP6 |
| 1 | XIAO-C6 | XIAO-SEEDSTUDIO:XIAO-ESP32-C6-SMD | U3 |
More from joehanko/MACK-10
1- 2 layers80 × 85.7 mm

Similar boards
- 2 layers56 × 81.5 mm

Pipette tool
rodrigue-laboratory/pipette-tool-pcb
bash kicad-cli pcb export gerbers pipettetool.kicadpcb --output fab/gerbers kicad-cli pcb export drill pipettetool.kicadpcb --output fab/gerbers --format excellon
38 parts1BSD-3-Clause - 4 layers50 × 32.5 mm

MCU&Motor Driver
p348X/Motor-Driver-MCU-Shield-Board
This github contain the schematic and KiCad file of TMC2208-LA motor driver and ESP shield board
21 parts - 4 layers

Corevus k
calithameridi/corevus
High-flexibility, low-cost mechatronics controller for 3D printers
283 parts25 - 2 layers

- 2 layers150 × 100 mm

- 2 layers100 × 100 mm

Mcu
cs2dsb/coffee_assistant
Free and open source software distributed under the terms of both the [MIT License][lm] and the [Apache License 2.0][la].
168 parts10Apache-2.0 - 2 layers51 × 23 mm

The Surevival
Rishaan2202/The_Soldering_Test
So this is gonna be a very basic pcb, which is supposed to have many kinda footprints in which we need to solder components, it has many basic and common footprints of SMT and THT devices so that we could increase our…
75 parts1MIT - 4 layers45 × 30 mm

Questions
How big is the MACK10 Controller PCB?
It measures 57.3 × 67.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the MACK10 Controller use?
62 parts, built around the HX711, PCF8575DB, TMC2208-LA and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the MACK10 Controller KiCad files?
From the joehanko/MACK-10 repository on GitHub, at the commit this page was made from: the board is electronics/MACK10_Controller v2/MACK10_Controller.kicad_pcb and its schematic electronics/MACK10_Controller v1/MACK10_Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the MACK10 Controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask joehanko before reusing the design.