

HD6309sbc
Single board computer using Hitachi HD6309
- Size
- 99.8 × 99.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 65
- Nets
- 111
- Pads
- 367
- Tracks, vias
- 1,171, 176
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 4 Oct 2022
- Updated
- 17 Jun 2025
Overview
HD6309sbc is an open-source printed circuit board by jimbro1000, from the jimbro1000/HD6309sbc repository on GitHub. It is a 4-layer board of 99.8 × 99.8 mm with 65 parts on 111 nets, routed with 1,171 tracks and 176 vias.
It is built around the HD63C09ERP, 74HCT541D and 74HCT138D, with the 74AHC1G14GV, 74HCT00D and 74HCT04D among its other parts. Its parts include 21 resistors, 17 diodes, 10 ICs, 8 capacitors and 5 connectors. It belongs with the computers and single-board computers boards of this library.
Main components
9HD63C09ERP
-Others - Microcontrollers (MCU/MPU/SOC) ROHSRenesas ElectronicsMicrocontrollers (MCU/MPU/SOC)74HCT541D
SO-20-40℃~+125℃ 1 15ns@4.5V,50pF 160uA 4.5V~5.5V 6mA 6mA 74HCT 8 Tri-State Unidirectional SO-20-300mil Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffers, Drivers, Receivers, Transceivers74HCT138D
SO-16-40℃~+125℃ 160uA 20ns@4.5V,50pF 3/8 4.5V~5.5V 4mA 4mA 74HCT Decoder Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches / Encoders & Decoders / Multiplexers74AHC1G14GV
SOT-23-5-40℃~+125℃ 1 1 1.2V~2.2V、1.75V~3.15V、2.15V~3.85V 16.3ns@3.3V,15pF 2V~5.5V 40uA 74AHC 8mA 8mA 900mV~1.9V、1.35V~2.75V、1.65V~3.35V SOT-23-5 Logic Gates ROHSTECH PUBLICLogic Gates74HCT00D
SO-14-40℃~+125℃ 100mV、400mV 12ns@4.5V,50pF 2 2V 3.7V、4.4V 4 4.5V~5.5V 40uA 4mA 4mA 74HCT Series 800mV NAND Gate Overvoltage-tolerant input TTL Compatible CMOS SO-14 Logic Gates ROHSNexperiaLogic Gates74HCT04D
SO-14-40℃~+125℃ 1 19ns@4.5V,50pF 2V 2uA 3.7V 4.5V~5.5V 400mV 4mA 4mA 6 74HCT 800mV SO-14 Inverters ROHSNexperiaInverters74HCT30D
SO-14-40℃~+125℃ 1 28ns@4.5V,50pF 2V 2uA 4.5V~5.5V 4mA 4mA 74HCT Series 800mV NAND Gate SO-14 Logic Gates ROHSNexperiaLogic Gates74HCT574D
SO-20-300mil-40℃~+125℃ 1 18ns@4.5V,50pF 3.5pF 3ns 4.5V~5.5V 5ns 69MHz 6mA 6mA 74HCT Series 8 8uA D-Type Rising Edge Tri-State SOIC-20-300mil Flip Flops ROHSNexperiaFlip FlopsDS1813-5+
TO-92-3-40℃~+85℃@(Ta) 1 1.2V~5.5V 150ms 4.75V Active Low No Open Drain Voltage Monitor Yes TO-92-3 Supervisor and Reset ICs ROHSAnalog DevicesSupervisor And Reset ICs
README
README.mdHD6309 single board computer
This project is a somewhat hopeful and probably overly grandiose attempt to create an expandable single board computer utilising the Hitachi HD63C09 processor at its core (the ultimate version of the ultimate 8-bit processor, allegedly)
Status
The current version is built and under test. So far the board is working with a single point of note. The reset line, when released it not reaching a full high value. It is enough that the processor treats it as released but I believe this is a borderline condition which could result in spurious resets
Architecture
The board is very, very basic and provides only clock, cpu and memory. All other functions are handled off-board via an expansion port
The CPU is clocked at 3MHz but each memory access is cycle is only half of the CPU clock duration allowing the memory to be shared by two CPUs operating at 3MHz
Memory
The board operates in two modes, either a 50:50 split on ram and rom, or a 64KB ram model with up to 4MB of paging (using 16k pages, yes that's a lot of pages)
Memory Map
RAM/ROM model
$0000 - $7FFF - shared ram
$8000 - $FEFF - rom
$FF00 - $FFEF - mapped hardware registers
$FFF0 - $FFFF - interrupt vectors
Paged RAM model (requires memory board)
$0000 - $7FFF - shared ram
$8000 - $BFFF - paged ram
$C000 - $FFEF - private ram
$FF00 - $FFEF - mapped hardware registers
$FFF0 - $FFFF - interrupt vectors
Hardware registers
The switching of memory models is handled by writing to bit 0 of address $FF24. Writing a low bit sets the map to RAM/ROM, writing a high bit sets the map to paged RAM
Bits 1 to 7 are unused by default but are exposed over the expansion bus to provide switching to other devices
For future use all addresses from $FF00 to $FFEF are reserved for memory mapped registers. The "MAPPED_MEM" line (pin 27) on the expansion bus is high for all addresses in this range. This should help to keep logic on expansion boards down where a new register is added
For expansion purposes the following addresses are fixed and should not be reused:
$FF00:$FF03 - PIA 1 $FF04:$FF07 - PIA 2 $FF08:$FF0B - PIA 3 $FF0C:$FF0F - ACIA $FF10:$FF1F - Video Co-Pro registers $FF24 - Hardware enable lines (Q0 = memory model, Q1-Q7 unused) $FF25:$FF27 - reserved for additional enable lines $FF40:$FF48 - Floppy Disc Controller $FF50:$FF5F - Hard Drive / MMC Controller
Expansion port
The processor board exposes all of the CPU and timing control lines over a 60 pin IO port to allow other devices to interface with the processor
Intended components are audio output, video co-processor, general peripheral IO and (slow) serial IO
Associated designs
- Backplane https://github.com/jimbro1000/SBCBackplane
- Memory Board https://github.com/jimbro1000/SBCMemoryBoard
- Peripheral Adapter https://github.com/jimbro1000/PIA-Module
- VGA Board https://github.com/jimbro1000/PicoVideoModule
- 6847Pi https://github.com/jimbro1000/6847Pi
- ACIA Board https://github.com/jimbro1000/ACIA-Module
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 470R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R7, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21 |
| 14 | LED_Filled | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16, D17 |
| 7 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C4, C5, C6, C7, C8 |
| 4 | 4.7k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4, R5, R6 |
| 3 | 330R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R8, R9 |
| 3 | 4K7 | Resistor_THT:R_Array_SIP9 | RN1, RN2, RN3 |
| 2 | 74HCT138 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U4, U12 |
| 2 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J3 |
| 2 | Conn_01x07_Socket | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J4, J5 |
| 1 | 100uF | Capacitor_SMD:CP_Elec_6.3x5.8 | C3 |
| 1 | 74AHC1G14 | Package_TO_SOT_SMD:SOT-353_SC-70-5_Handsoldering | U3 |
| 1 | 74HCT00 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U17 |
| 1 | 74HCT04 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U18 |
| 1 | 74HCT30 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U19 |
| 1 | 74HCT541 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U16 |
| 1 | 74HCT574 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U7 |
| 1 | Conn_02x30_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x30_P2.54mm_Vertical | J2 |
| 1 | DS1813 | Package_TO_SOT_SMD:SOT-23-3 | U2 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | HD63C09 | Package_LCC:PLCC-44_THT-Socket | U1 |
| 1 | RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3S-1000 | SW1 |
| 1 | YELLOW | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
Similar boards
- 2 layers368.3 × 215.9 mm

- 4 layers230 × 100 mm

- 4 layers280 × 140 mm

P8x io card
ksr/p8x
Generated by generators/genkicad.py from the canonical geneagle netlist (CARDS["peripheral-card"]), same standard as the memory card: 4-layer (F/B signals, In1=GND, In2=VCC planes), a bypass cap above each IC, a…
63 parts - 2 layers62.9 × 61.6 mm

- 2 layers333.4 × 149.9 mm

- 2 layers333.4 × 149.9 mm

- 2 layers238 × 174 mm

- 2 layers127 × 127 mm

Morseboard-8088
ifilot/morseboard-8088
Single board computer designed around the 8088 processor
61 parts
Questions
How big is the HD6309sbc PCB?
It measures 99.8 × 99.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the HD6309sbc use?
65 parts, built around the HD63C09ERP, 74HCT541D, 74HCT138D and 74AHC1G14GV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HD6309sbc KiCad files?
From the jimbro1000/HD6309sbc repository on GitHub, at the commit this page was made from: the board is HD6309sbc.kicad_pcb and its schematic HD6309sbc.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the HD6309sbc design in my own project?
Its repository states no licence, so its author keeps all rights: ask jimbro1000 before reusing the design.