Skip to the content
2 layers20.1 × 36.9 mmDragonRomAdapter, the printed circuit board in 3D

Convert your Dragon to use a modern EEPROM in place of the old masked ROMs

Size
20.1 × 36.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
31
Pads
75
Tracks, vias
132, 11
Pours
1
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
21 Oct 2022
Updated
11 Sep 2023

Overview

DragonRomAdapter is an open-source printed circuit board by jimbro1000, from the jimbro1000/Dragon32RomFix repository on GitHub, published under the MIT licence. It is a 2-layer board of 20.1 × 36.9 mm with 11 parts on 31 nets, routed with 132 tracks and 11 vias.

Its parts include 3 resistors, 3 ICs and 1 connector.

README

README.md

Dragon 32 Rom Adapter Fix

This project details a simple conversion board to replace two 8K masked ROMs with a single modern EEPROM.

The board is designed to accept 28 pin eeproms compatible with the Atmel AT28C range.

Direct (Twin) Rom Replacement

If the replacement ROM is a AT28C64 the board must be configured for a 1:1 swap with one adapter for each ROM position. There is no need to fit any of the SMT components or the 3 pin jumper.

If the replacement ROM is a AT28C256 the board needs to be assembled with the 3 pin jumper and a resistor at R1 and R3. The jumper at JP2 must be bridged. This then allows the selection of a different ROM image by moving the JP1 jumper between positions (only when powered down). Only half of the ROM capacity will be used and the images should be loaded at $0000 and $4000. The memory space between $2000-$3FFF and $6000-$7FFF cannot be accessed in this mode without modifying the board.

Bodging the Board

In order to fully utilise the available memory space in this configuration it is necessary to find a way to drive pin 26 of the eeprom by optionally inverting the signal to it.

The NAND gate position at U2 can be used as an inverter by taking the signal from pin 20 of the input socket and feeding it to J1. Some cutting of traces will also be needed to avoid Putting a jumper or switch on that lead will allow you to switch between the two possible memory spaces (effectively giving you 4 selectable images). Ideally it should be a jumper with the "off" position going to pin 3 of JP1 (the pin furthest from R1).

Single Rom Setup

If the replacement ROM is a AT28C256 the board can be configured for a 2:1 swap. In this arrangement it is essential to fully populate the board with all 3 resistors and the NAND gate. A fly lead from J1 is also needed.

In this arrangement the board should be fitted to position IC18 with the flylead going to pin 20 of IC17.

JP1 still allows swapping between two different ROM images but all of the memory space on the ROM will be utilised. The first image is from $0000-$3FFF and the second image is from $4000-$7FFF.

It is possible to fit the board in position IC17 but the ROM images will need resequencing:

$0000-$1FFF => ROM1 1-1
$2000-$3FFF => ROM1 1-0
$4000-$5FFF => ROM2 1-1
$6000-$7FFF => ROM2 1-0

BOM

PositionComponent
R1, R2, R34K7 0805
U12 x 12 position 2.54mm pin header
U274AHCT1G00 SOT-353
U3DIP-28 socket
JP13-pin right-angle 2.54mm pin header

The resistor values given are recommended - all 3 are acting as pull-up or pull-down purposes so smaller or larger values can be used as appropriate. It is also possible to simply solder bridge the positions but this has potential to damage the EEPROM.

For the U1 pin headers I recommend using turned-pins and fitting a turned-pin socket on the main board to ensure a quality fit and no damage from repeated insertions. Using square pins will ultimately damage a regular single- or double-wipe socket but it is possible to fit female pin headers to ensure compatibility but this then prevents putting regular (original) Dragon ROMs back in.

Parts

11
QtyValueFootprintReferences
34K7Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1, R2, R3
2SolderJumper_3_OpenJumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabelsJP3, JP4
128C256Package_DIP:DIP-28_W15.24mmU3
168A364Package_DIP:DIP-24_W15.24mmU1
174ACHT1G00Package_TO_SOT_SMD:SOT-353_SC-70-5_HandsolderingU2
1Conn_01x01_MaleConnector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ1
1Jumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mmJP2
1Jumper_3_Bridged12Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_HorizontalJP1

Similar boards

  • 2 layers60 × 30 mmController, the printed circuit board in 3D

    Controller

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    11 parts3kApache-2.0
  • 2 layers103 × 30.5 mmTS Front Endcap, the printed circuit board in 3D

    TS Front Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    11 parts1.3kMIT
  • 2 layers26 × 30 mmExpansion Card, the printed circuit board in 3D

    Expansion Card

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    11 parts1.1kCC-BY-4.0
  • 2 layers53.9 × 23.2 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    11 parts1kGPL-3.0
  • 2 layers10 × 20 mm2 connector Sensor Board, the printed circuit board in 3D

    2 connector Sensor Board

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    11 parts915
  • 2 layersFet module, the printed circuit board in 3D

    Fet module

    ByteWelder/Decktility

    A handheld PC

    11 parts855CC-BY-SA-4.0
  • 2 layers47 × 33 mmSevensegment led display module, the printed circuit board in 3D

    Sevensegment led display module

    tardate/LittleArduinoProjects

    a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

    11 parts803MIT
  • 2 layers42.5 × 36.8 mmDevboard, the printed circuit board in 3D

    Devboard

    basilfx/TRADFRI-Hacking

    Hacking IKEA TRÅDFRI products, such as light bulbs, window blinds and other accessories.

    11 parts743CC-BY-4.0

Questions

How big is the DragonRomAdapter PCB?

It measures 20.1 × 36.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the DragonRomAdapter use?

11 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the DragonRomAdapter KiCad files?

From the jimbro1000/Dragon32RomFix repository on GitHub, at the commit this page was made from: the board is DragonRomAdapter.kicad_pcb and its schematic DragonRomAdapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the DragonRomAdapter design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).