Skip to the content
2 layers79.4 × 31.8 mmA500HIDpico, the printed circuit board in 3D

hardware Raspberry Pico Amiga 500 Keyboard to USB Adapter

Size
79.4 × 31.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
6
Nets
63
Pads
134
Tracks, vias
59, 0
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
25 May 2022
Updated
25 May 2022

Overview

A500HIDpico is an open-source printed circuit board by jimbro1000, from the jimbro1000/A500keyboard repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 79.4 × 31.8 mm with 6 parts on 63 nets, routed with 59 tracks and 0 vias.

Its parts include 3 ICs, 2 capacitors and 1 connector. It belongs with the keyboards and input boards and the RP2040 boards of this library.

README

README.md

A500 Keyboard HID Adapter

This is a (prototype) project to develop a simple adapter for the Amiga 500 keyboard for connection via USB. The project is not particularly revolutionary, other similar projects exist but require the use of more expensive microcontrollers while this solution aims to use the remarkably cheap RP2040 controller (aka Raspberry Pico)

Components Used

Right now this is being built on a breadboard but the design is mirrored as a KiCad project.

The initial approach is to utilise a pair of CD4050 hex non-inverting buffers to manage level shifting between the keyboard (which operates at 5v) and the RP2040 (operating at 3.3v).

The shift up to 5v is only required to drive LEDs on the keyboard so not actually mandatory but in order to achieve full brightness the 5v is needed. This could be achieved with a couple of transistors but the CD4050 chips are cheap enough and readily available such that it is an equally simply solution.

If you don't care about the brightness of the LEDs then you could simply miss the second CD4050 out and just jumper between two pairs of pins.

The inclusion of smoothing caps on the board is equally speculative. For the LED drivers it should be completely unnecessary given the frequencies used. For the keyboard data lines though it is strongly recommended to make sure the quality of transmission is maintained.

All in a single prepared board should cost roughly £14 (being somewhat pessimistic with component prices). Given the price point on the PCB in batches of 10 and similar bulk prices on the Pico board that could easily be reduced down to just £9 (being optimistic). Deleting the second CD4050 should save another £0.20-0.60 (if you're paying more that for CD4050s something is wrong).

Parts

6
QtyValueFootprintReferences
21nFCapacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mmC1, C2
24050Package_DIP:DIP-16_W7.62mmU2, U3
1Conn_01x08_MaleConnector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ1
1PicoMCU_RaspberryPi_and_Boards:RPi_Pico_SMD_THU1

Similar boards

  • 2 layers18.5 × 11.1 mmSwitch, the printed circuit board in 3D

    Switch

    byrantech/laptop

    anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.

    6 parts4.3kMIT
  • 2 layers14.6 × 33 mmBrain board SD Card 1, the printed circuit board in 3D

    Brain board SD Card 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    6 parts1.2k
  • 2 layers9 × 9 mmDpoint, the printed circuit board in 3D

    Dpoint

    Jcparkyn/dpoint

    Open-source digital stylus using camera tracking and inertial measurements

    6 parts1.1kMIT
  • 2 layers51.5 × 16.6 mmMicroswitchXY Endstop, the printed circuit board in 3D

    MicroswitchXY Endstop

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    6 parts1.1kGPL-3.0
  • 2 layers21.9 × 76.7 mmAmiga External, the printed circuit board in 3D

    Amiga External

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    6 parts1kGPL-3.0
  • 2 layers88.9 × 50.8 mmBusinesscard, the printed circuit board in 3D

    Businesscard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    6 parts915
  • 2 layers20.3 × 15.2 mmL0 RGB led, the printed circuit board in 3D

    L0 RGB led

    Luos-io/luos_engine

    Open-source and real-time orchestrator for cyber-physical-systems, to easily design, test and deploy embedded applications and digital twins.

    6 parts546MIT
  • 2 layers9 × 3.6 mmOpticalEncoder, the printed circuit board in 3D

    OpticalEncoder

    adamb314/ServoProject

    Getting the most out of your hobby servo

    6 parts545

Questions

How big is the A500HIDpico PCB?

It measures 79.4 × 31.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the A500HIDpico use?

6 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the A500HIDpico KiCad files?

From the jimbro1000/A500keyboard repository on GitHub, at the commit this page was made from: the board is kicad/A500HIDpico.kicad_pcb and its schematic kicad/A500HIDpico.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the A500HIDpico design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).