Skip to the content
2 layers25.7 × 19 mmTLC6C598-breakout, the printed circuit board in 3D

TLC6C598-breakout

jedp/TLC6C598-breakout

TLC6C598 Shift register / LED driver breakout board

Size
25.7 × 19 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
23
Pads
69
Tracks, vias
124, 16
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
22 Dec 2023
Updated
31 Dec 2023

Overview

TLC6C598-breakout is an open-source printed circuit board by jedp, from the jedp/TLC6C598-breakout repository on GitHub. It is a 2-layer board of 25.7 × 19 mm with 21 parts on 23 nets, routed with 124 tracks and 16 vias.

It is built around the TLC6C598PW. Its parts include 8 resistors, 8 diodes, 2 capacitors, 1 IC and 1 connector. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

TLC6C598 Shift register / LED driver breakout board

The correct timing can be achieved with SPI polarity=0, phase=0. In CubeMX, this corresponds to CPOL=Low, CPHA=1 edge.

/CLS can be tied high.

Timing Diagram

After shifting in data, you have to manually raise and lower a GPIO to act as a register clock to cause the TLC to transfer that data to the storage registers for display, which is done on the rising edge of RCK.

Since the high time of the register clock is the same as the serial clock, you can achieve this by pulling the clock GPIO low before transmitting data and then pulling it high when you're done.

text
	// Register clock low.
	HAL_GPIO_WritePin(GPIOA, GPIO_RCK, GPIO_PIN_RESET);
	
	// Shift data ...
	HAL_SPI_Transmit(&hspi1, (uint8_t*) data, 1, 1);

	// Register clock high: See the blinkies.
	HAL_GPIO_WritePin(GPIOA, GPIO_RCK, GPIO_PIN_SET);

PCB Image

Parts

21
QtyValueFootprintReferences
8330Resistor_SMD:R_0603_1608MetricR1, R2, R3, R4, R5, R6, R7, R8
8LED_SmallLED_SMD:LED_0603_1608MetricD1, D2, D3, D4, D5, D6, D7, D8
10.1uFCapacitor_SMD:C_0603_1608MetricC2
11uFCapacitor_SMD:C_0805_2012MetricC1
1Conn_01x07_FemaleConnector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ1
1LOGOLOGOG***
1TLC6C598Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm_EP3x3mm_ThermalViasU1

Similar boards

  • 2 layers76.2 × 117.5 mmNumbpad, the printed circuit board in 3D

    Numbpad

    scott-t-wilson/numpad

    DIY USB numpad - C++ code for teensy + schematic and pcb

    73 parts
  • 2 layers28.3 × 39.8 mmLevelShifter, the printed circuit board in 3D

    LevelShifter

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    21 parts5.1kGPL-3.0
  • 2 layers171.2 × 72.9 mmAmiga gfxcard before pour, the printed circuit board in 3D

    Amiga gfxcard before pour

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    21 parts1k
  • 2 layers93.9 × 46 mmRectifier, the printed circuit board in 3D

    Rectifier

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    21 parts990GPL-3.0
  • 2 layers45.5 × 42.9 mmEsphome han reader, the printed circuit board in 3D

    Esphome han reader

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    21 parts915
  • 2 layers31.8 × 14.5 mmEsp prog, the printed circuit board in 3D

    Esp prog

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    21 parts744MIT
  • 2 layers23.5 × 15.8 mmQuiverAttachPCB, the printed circuit board in 3D

    QuiverAttachPCB

    Arrow-air/project-quiver

    Project Quiver documentation, designs, and project artifacts.

    21 parts617CERN-OHL-S-2.0

Questions

How big is the TLC6C598-breakout PCB?

It measures 25.7 × 19 mm and has 2 copper layers, 1.6 mm thick.

What parts does the TLC6C598-breakout use?

21 parts, built around the TLC6C598PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the TLC6C598-breakout KiCad files?

From the jedp/TLC6C598-breakout repository on GitHub, at the commit this page was made from: the board is TLC6C598-breakout.kicad_pcb and its schematic TLC6C598-breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the TLC6C598-breakout design in my own project?

Its repository states no licence, so its author keeps all rights: ask jedp before reusing the design.