Jed0vcela/Linear-CCD-camera-V11Prototype of "scanning" camera using linar CCD sensor ILX555K
Linear CCD camera V1 is an open-source printed circuit board by Jed0vcela, from the Jed0vcela/Linear-CCD-camera-V1 repository on GitHub. It is a 2-layer board of 95.4 × 90.9 mm with 100 parts on 109 nets, routed with 1,544 tracks and 198 vias.
It is built around the TLV9064ID, MSD-1-A and 74HC14, with the AMS1117-5.0, BC817 and FFC2B35-18-G among its other parts. Its parts include 35 resistors, 28 capacitors, 9 ICs, 4 diodes and 3 transistors. It belongs with the RP2040 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C5, C6, C7, C8, C9, C11, C12, C13, C14, C15, C17, C18, C23, C27, C28, C30 |
| 12 | 5k1 | Resistor_SMD:R_0603_1608Metric | R17, R18, R19, R20, R21, R22, R23, R24, R25, R26, R27, R28 |
| 7 | 100 | Resistor_SMD:R_0603_1608Metric | R7, R8, R9, R10, R11, R12, R13 |
| 6 | 1u | Capacitor_SMD:C_0603_1608Metric | C16, C19, C21, C22, C25, C26 |
| 4 | 2 | Resistor_SMD:R_0603_1608Metric | R3, R4, R5, R6 |
| 4 | D_Schottky | Diode_SMD:D_SMA | D1, D2, D3, D4 |
| 3 | 10K | Potentiometer_THT:Potentiometer_Piher_PT-6-V_Vertical | RV1, RV2, RV3 |
| 3 | 2k | Resistor_SMD:R_0603_1608Metric | R2, R14, R38 |
| 3 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 3 | NC | Capacitor_SMD:C_0603_1608Metric | R30, R31, R32 |
| 2 | 18k | Resistor_SMD:R_0603_1608Metric | R1, R37 |
| 2 | 4u7 | Inductor_SMD:L_7.3x7.3_H3.5 | L1, L3 |
| 2 | 74HC14 | Package_SO:SO-14_3.9x8.65mm_P1.27mm | U4, U8 |
| 2 | C_Polarized | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C4, C24 |
| 2 | Conn_01x02_Pin | Connector_Molex:Molex_SPOX_5267-02A_1x02_P2.50mm_Vertical | batt1, end_sw1 |
| 2 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | stepper1, stepper2 |
| 2 | FFC2B35-18-G | Connector_FFC-FPC:Hirose_FH12-18S-0.5SH_1x18-1MP_P0.50mm_Horizontal | J5, J6 |
| 2 | NC | Capacitor_SMD:C_0805_2012Metric | C10, C29 |
| 2 | NC | Resistor_SMD:R_0603_1608Metric | R16, R33 |
| 2 | Pololu_Breakout_A4988 | Module:Pololu_Breakout-16_15.2x20.3mm | A2, A3 |
| 2 | TLV61048DBVR | SamacSys_Parts:SOT95P280X145-6N | IC1, IC2 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 10u | Capacitor_SMD:C_0603_1608Metric | C20 |
| 1 | 2k | Capacitor_SMD:C_0603_1608Metric | R15 |
| 1 | 470k | Resistor_SMD:R_0603_1608Metric | R29 |
| 1 | AMS1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U7 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | LM4040DBZ-3 | Package_TO_SOT_SMD:SOT-23 | U6 |
| 1 | MCP73832-2-OT | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | MSD-1-A | SamacSys_Parts:MSD1A | J1 |
| 1 | OLED-128O064D | Display:OLED-128O064D | DS1 |
| 1 | RaspberryPi_Pico_W | Module:RaspberryPi_Pico_W_SMD_HandSolder | A1 |
| 1 | RotaryEncoder_Switch_MP | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm_MountingHoles | SW1 |
| 1 | SLW-135987-5A-N-D | SamacSys_Parts:SLW1359875AND | S2 |
| 1 | SolderJumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm | JP1 |
| 1 | TLV9064 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U9 |
| 1 | charge | LED_SMD:LED_0603_1608Metric | charge1 |
| 1 | ~ | sensor-optic:DIP-22_400_ELL | U1 |
kwiecinski/BMS-and-offgrid-photovoltaic-management-system
Project contains BMS for lead-acid batteries and ESP-based board used to pull information from EASUN offgrid inverter, energy meters and sensors.
embedded-pro/e-foc-hardware
hardware to be used with https://github.com/embedded-pro/e-foc
It measures 95.4 × 90.9 mm and has 2 copper layers, 1.6 mm thick.
100 parts, built around the TLV9064ID, MSD-1-A, 74HC14 and AMS1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Jed0vcela/Linear-CCD-camera-V1 repository on GitHub, at the commit this page was made from: the board is linear CCD camera V1.kicad_pcb and its schematic linear CCD camera V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Jed0vcela before reusing the design.