Skip to the content
2 layers76.2 × 114.3 mmMMTR AFE 00 04 TORELEASE, the printed circuit board in 3D

MMTR AFE 00 04 TORELEASE

jduffy105/HydraMeter_0.4178

Open source multimeter

Size
76.2 × 114.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
312
Nets
196
Pads
845
Tracks, vias
3,569, 347
Pours
3
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
11 Dec 2024
Updated
13 Jul 2026

Overview

MMTR AFE 00 04 TORELEASE is an open-source printed circuit board by jduffy105, from the jduffy105/HydraMeter_0.4 repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 76.2 × 114.3 mm with 312 parts on 196 nets, routed with 3,569 tracks and 347 vias.

It is built around the 1N4007FL. Its parts include 85 resistors, 59 connectors, 54 capacitors, 21 transistors and 13 diodes.

Main components

1

README

README.md

HydraMeter_0.4

Open source multimeter

Intro

I don't have detailed assembly documents yet, and this isn't really well made for easy assembly in any case, it's a proof of concept at the moment.

There are some more details here: https://hackaday.io/project/176607-hydrameter but it's not much. Mainly a few entries down there's a tour of how the analog stuff works: https://hackaday.io/project/176607-hydrameter/log/223270-schematic-and-operation

Repository structure

Notes

I would recommend 24 to 28 AWG stranded wire for connecting to switches, except the mA/uA switch, for which I'd use 20AWG. The switches should pull inputs to the 74165s to ground, for numbering you'll have to check the code (or adjust it), when assembled I just wired up all of them then recorded which switch went where, I don't have a list or diagram. On the board these are labeled A-H, one set is near the middle of the board, the other next to the module connector.

Hardwired connections are: the two ohms jumpers (J7 and J8) are wired to the second pole of the lower-right switch (right from the front), and the mA/uA switch goes to J5 and J6.

There's a hardwired connection from J30 to J34, which should be made with at least 18AWG wire, as it carries the full current for the 10A range.

Tweaks

Note that this version of the PCB has some tweaks from the last manufactured version, these have not been verified to work.

The as-made PCB is under version 0.3, however, this version requires significant manual rework including:

  • pullup resistors for all switches to D3V3
  • cutting jumpers to the Module outputs (J96-99, to configure them as inputs), and wiring switches to them
  • additional capacitors on D3V3 to D0V, to stabilize the rail when using a radio module
  • DNP U5, and bridge pin 3 to pin 4
  • DNP: R74, D5, C72, R76, R77, U26, R78, Q20, Q21, R80, R79
  • Replace R33 with a ~16K resistor, or two 33K in parallel
  • Manually cut the trace going to pin 10 on U12, U13 and U16 (pulling it to D0V), and wire that pin on the chip to D3V3
  • U18 has the wrong footprint (SOIC-16 used on the board, the actual chip is a SOIC-14).
  • Angle U18 such that only pins 14-9 make contact with the board (so pins 1-7 are above the surface), and solder in place.
  • Then manually wire pins 2-7 to the appropriate pads with short wires.
  • If using a battery, a protected cell must be used, there is no circuitry onboard to protect from over or under voltage.
  • Positive should be soldered to J10, negative to J11.

To charge, two diodes can be placed in series from VBUS on the PI pico (MCU_VBUS) to battery positive (charging the battery when USB is plugged in). Bypassing one of the diodes with a 50 or 100 ohm resistor can improve charge time. This however WILL overcharge the battery if proper cell protection is not in place! This is a terrible hack solution I used to get something working in like an hour. Use a charger IC or board or something.

License

This project uses the CERN Open Hardware Licence Version 2 - Strongly Reciprocal. Any derived works must fall under the same license and must be open source themselves.

Parts

312
QtyValueFootprintReferences
34~AADuffy:Header_Pin_01x01DM1, DP1, J5, J10, J11, J24, J30, J34, J39, J40, J43, J100, J101, J102, J103, J104 +18
3210KAADuffy:Resistor_0603R6, R7, R8, R10, R24, R34, R39, R40, R41, R42, R43, R48, R50, R61, R62, R79 +16
29~AADuffy:Test_Pad_30x30milJ12, J13, J15, J16, J17, J18, J19, J20, J21, J22, J23, J25, J26, J27, J28, J105 +13
22100nAADuffy:Cap_SMD_0603C3, C13, C16, C18, C20, C22, C23, C29, C30, C32, C33, C34, C35, C37, C38, C39 +6
12~AADuffy:DMN65D8L-7Q1, Q2, Q3, Q4, Q5, Q6, Q12, Q15, Q16, Q17, Q19, Q20
111N4007FLAADuffy:1N4007FLD1, D2, D6, D7, D8, D9, D10, D11, D12, D13, D14
11NCAADuffy:Jumper_0603J9, J47, J48, J49, J50, J51, J62, J63, J80, J81, J82
91KAADuffy:Resistor_0603R11, R18, R19, R20, R21, R22, R23, R31, R80
9~AADuffy:SOT23-3Q7, Q8, Q9, Q10, Q11, Q13, Q14, Q18, Q21
8100KAADuffy:Resistor_0603R35, R36, R37, R38, R47, R51, R52, R57
6330KAADuffy:Resistor_0603R44, R46, R56, R59, R60, R65
51uAADuffy:Cap_SMD_0603C4, C21, C56, C68, C70
410uAADuffy:Cap_SMD_1206C19, C26, C31, C36
447uAADuffy:Cap_SMD_1206C9, C11, C14, C57
4NOAADuffy:Jumper_0603_NOJ14, J45, J52, J79
4~AADuffy:CT2914J1, J2, J3, J4
31uAADuffy:Cap_SMD_1206C12, C27, C28
32u2AADuffy:Cap_SMD_0603C7, C8, C15
333KAADuffy:Resistor_0603R32, R33, R58
33V3AADuffy:MOV_0603RT4, RT5, RT6
3510KAADuffy:Resistor_0603R49, R55, R64
374HC595BQ,115AADuffy:16-DHVQFN_74HC595BQU12, U13, U16
2100KAADuffy:Resistor_THT_Vert_0p2_1o4WR1, R2
2100KAADuffy:Resistor_1206R13, R28
21MAADuffy:Resistor_0603R45, R78
21nAADuffy:Cap_SMD_0603C24, C25
2400KAADuffy:Resistor_THT_Vert_0p2_1o4WR3, R4
250AADuffy:Resistor_0603R5, R54
2SN74HCS165PWRAADuffy:TSSOP-16U27, U28
2~AADuffy:MiniPin_25milJ44, J46
2~AADuffy:CUS08F30,H3FD3, D4
10.1uAADuffy:Cap_TH_Film_0.3SpcC72
11.5nAADuffy:Cap_TH_Film_0.4SpcC54
11.8nAADuffy:Cap_SMD_0603C59
1100AADuffy:Resistor_0603R53
1100AADuffy:Resistor_1206R17
1100nAADuffy:Cap_SMD_0805C66
1100pAADuffy:Cap_SMD_0603C2
110KAADuffy:Resistor_1206R27
110mAADuffy:Resistor_2512_4PinR15
110nAADuffy:Cap_SMD_0603C10
110pAADuffy:Cap_SMD_0603C1
1120AADuffy:Resistor_0603R63
116AAADuffy:FC-102_BRIGHT_TINF1
118VAADuffy:MOV_0805RT7
11KAADuffy:Resistor_1W_Thru_WideR25
11MAADuffy:Resistor_1206R29
1220KAADuffy:Resistor_1206R77
1220pAADuffy:Cap_TH_Film_0.2SpcC55
1230 VRMSAADuffy:B72205S0231K311RT1
127nAADuffy:Cap_SMD_0603C61
12u2AADuffy:Cap_SMD_1206C17
13.3VAADuffy:MOV_0603RT3
13.3VAADuffy:SOT23-5U25
13.3VAADuffy:SOT23-3U11
1330mAADuffy:Resistor_1206R16
133pAADuffy:Cap_SMD_0603C73
13K3AADuffy:Resistor_0603R30
1500mAAADuffy:FC-102_BRIGHT_TINF2
1500mOhmAADuffy:WCM 2012F2SF-361T03L1
1510AADuffy:Resistor_1206R26
1510KAADuffy:Resistor_1206R76
15VAADuffy:SOT23-5U9
163mAAADuffy:0034.6062F3
16K8AADuffy:Resistor_0805R14
174LVC1G126W5-7AADuffy:SC-74AU29
175 VRMSAADuffy:2045-07-BLFRT2
17Vf 12VrAADuffy:SOT23-3U26
18kbitAADuffy:SOT23-3U20
19M1AADuffy:Resistor_1206R12
1DSLVDS1001DBVRAADuffy:SC-74A_DSLVDS1001DBVRU24
1IN_0AADuffy:Header_Pin_01x01J60
1IN_1AADuffy:Header_Pin_01x01J57
1IN_2AADuffy:Header_Pin_01x01J56
1IN_3AADuffy:Header_Pin_01x01J31
1IN_4AADuffy:Header_Pin_01x01J92
1IN_5AADuffy:Header_Pin_01x01J93
1IN_6AADuffy:Header_Pin_01x01J94
1IN_7AADuffy:Header_Pin_01x01J95
1IN_8AADuffy:Header_Pin_01x01J83

The 289 most common of 312 parts.

Similar boards

  • 4 layers80 × 100 mmHarp treadmill, the printed circuit board in 3D

    Harp treadmill

    AllenNeuralDynamics/harp.device.treadmill-driver

    0326: a Harp-compatible device for controlling an instrumented mouse treadmill

    173 parts4
  • 2 layers50.1 × 88.2 mmPtFlex, the printed circuit board in 3D

    PtFlex

    custom-ds/ptFlex

    ptFlex tracker board starting with version 2.0 of the hardware, which is based on the improvements found in the ptSolar tracker.

    76 parts3GPL-3.0
  • 2 layers143.2 × 85.8 mmDongle, the printed circuit board in 3D

    Dongle

    marx-merten/zmk-macropad

    35 parts3
  • 4 layers71.1 × 149.9 mmLCMTR 01 01, the printed circuit board in 3D

    LCMTR 01 01

    jduffy105/HydraMeter_L_DesignReview_0.1.1

    337 parts1
  • 2 layers130 × 105 mmDistributeur, the printed circuit board in 3D

    Distributeur

    jmolas42/Cat-Feeder

    automatic cat feeder

    90 parts1
  • 4 layers70 × 168 mmValve controller, the printed circuit board in 3D

    Valve controller

    AllenNeuralDynamics/harp.device.valve-controller

    0368: a 16-channel valve controller

    224 parts
  • 4 layers31.7 × 110 mmTiliqua motherboard, the printed circuit board in 3D

    Tiliqua motherboard

    antoinevg/tiliqua

    A powerful, hackable FPGA-based audio multitool for Eurorack.

    134 partsCERN-OHL-S-2.0
  • 4 layers90 × 90 mmPump Controller, the printed circuit board in 3D

    Pump Controller

    citrineio/Pump-Controller-V2

    Second Version of the pump controller PCB

    68 partsApache-2.0

Questions

How big is the MMTR AFE 00 04 TORELEASE PCB?

It measures 76.2 × 114.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MMTR AFE 00 04 TORELEASE use?

312 parts, built around the 1N4007FL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MMTR AFE 00 04 TORELEASE KiCad files?

From the jduffy105/HydraMeter_0.4 repository on GitHub, at the commit this page was made from: the board is MMTR_AFE_00_04_TORELEASE/MMTR_AFE_00_04_TORELEASE.kicad_pcb and its schematic MMTR_AFE_00_04_TORELEASE/Amp_AFE.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MMTR AFE 00 04 TORELEASE design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).