
PicoChainZero
jasonalexander-ja/PicoChain
Power and I2C daisy chained over ethernet patch cables.

Power and I2C daisy chained over ethernet patch cables.
PicoChainReference is an open-source printed circuit board by jasonalexander-ja, from the jasonalexander-ja/PicoChain repository on GitHub, published under the MIT licence. It is a 4-layer board of 68 × 34 mm with 22 parts on 17 nets, routed with 144 tracks and 28 vias.
It is built around the LM78M05CH, LM1085R-3.3 and PCA9615DP, with the SRV05 and RJ45 among its other parts. Its parts include 7 capacitors, 6 connectors, 5 ICs and 4 fuses. It belongs with the interfaces and adapters boards of this library.
Pico(Daisy)Chain is a simple standard for creating daisy chains of connected devices, allowing I2C and power to be easily distributed out using ethernet patch cables.
This is a repository containing documentation and reference hardware + software implementations.
All hardware reference implementations are in KiCAD 8+ format with the PCB layout and Gerbers.
PicoChain uses differential I2C, 12 + 24 volts, all sent down a single RJ45 & twisted pair allowing communication and power for microcontrollers + motors to be supplied using commonly available ethernet patch cables.
Generation of the differential I2C is handled by the NXP PCA9615 meaning that when SCL and SCA is hooked up to this chip, all the same I2C libraries and implementation automatically work with no further modifications.
The 12 + 24 volts is supplied with the assumption that this will be regulated into the relevant required voltages by the connected devices, the reference implementations regulates a 5V for the microcontroller and a 5V for servo and similar small motors off of the 12V line, and a 12V line is regulated off of the 24V line intended for high power motors.
Each PicoChain device has 2 RJ45 connectors to send and receive power and data, they don't have a particular direction are all the reference designs have the RJ45s passively connected, tapping off of power and I2C as needed, however, all PicoChain chains need terminators at either end.
Generally, this is designed for running sequences across some connected devices, with the idea that only 1 large load (I.E. a motor) will be running at a time, reducing the current load going through the patch cables and chained devices.
| RJ45 Pin | Function |
|---|---|
| 1 | GND |
| 2 | +24V |
| 3 | DSDAM |
| 4 | DSCLM |
| 5 | DSCLP |
| 6 | DSDAP |
| 7 | GND |
| 8 | +12V |
Pins 3-6 (inclusive) are generated by the PCA9615 and are connected directly to ICs on each device.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 330nF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C1, C2, C3, C4 |
| 4 | Fuse | Fuse:Fuse_0805_2012Metric | F1, F2, F3, F4 |
| 2 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B | C5, C6 |
| 2 | LM78M05 | Package_TO_SOT_SMD:TO-252-2 | U1, U2 |
| 2 | RJ45 | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J1, J2 |
| 1 | +12V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | +5V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | +5V(M) | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | I2C | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | LM1085 | LM1085IS-12:TO254P1524X483-4N | U3 |
| 1 | PCA9615DP | Package_SO:TSSOP-10_3x3mm_P0.5mm | U4 |
| 1 | SRV05 | Package_TO_SOT_SMD:SOT-23-6 | U5 |

jasonalexander-ja/PicoChain
Power and I2C daisy chained over ethernet patch cables.

jasonalexander-ja/PicoChain
Power and I2C daisy chained over ethernet patch cables.

jspark311/ViamSonus-2.0
An audio router board with integrated volume control and buffered output.





kornpow/sparkfun-kicad
Converting SparkFun OSH Eagle resources to KiCAD

robotique-udes/Exo_Electric
This repo contains all the information about the PCB and electrical schematics of Biogenius.

RomLab/pcb-system-for-underfloor-heating-v2.0
PCB for underfloor heating system
It measures 68 × 34 mm and has 4 copper layers, 1.6 mm thick.
22 parts, built around the LM78M05CH, LM1085R-3.3, PCA9615DP and SRV05. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the jasonalexander-ja/PicoChain repository on GitHub, at the commit this page was made from: the board is PicoChainReference/PicoChainReference.kicad_pcb and its schematic PicoChainReference/PicoChainReference.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).