4 layers39.4 × 98.5 mm
MOBO DEV BreadBoard
robotique-udes/Exo_Electric
This repo contains all the information about the PCB and electrical schematics of Biogenius.
46 parts1GPL-2.0
4 layers100 × 92 mm
Cerbrum Aeris
Jabooby/Aeris-Control2Projet de session S4
- Size
- 100 × 92 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 109
- Nets
- 189
- Pads
- 536
- Tracks, vias
- 1,348, 369
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 8 Jan 2025
- Updated
- 13 Apr 2025
Overview
Cerbrum Aeris is an open-source printed circuit board by Jabooby, from the Jabooby/Aeris-Control repository on GitHub, published under the MIT licence. It is a 4-layer board of 100 × 92 mm with 109 parts on 189 nets, routed with 1,348 tracks and 369 vias.
It is built around the W25Q128JVPIQ, AP7361C-33E and SRV05-4, with the AO3401A and SMD0805B110TF among its other parts. Its parts include 31 connectors, 25 capacitors, 17 resistors, 5 ICs and 2 inductors. It belongs with the RP2350 boards of this library.
Main components
5
W25Q128JVPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 120ms@(32KB) 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASH
AP7361C-33E
SOT-223-40℃~+85℃@(Ta) 1 1A 3.3V 340mV@(1A) 6V 75dB@(1kHz) 80uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
AO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
SMD0805B110TF
0805-40℃~+85℃ 1.1A 1.5mm 1.5mm 100A 2.2mm 210mΩ 2A 300ms 35mΩ 6V 800mW 0805 Resettable Fuses ROHSBrightkingResettable Fuses
README
README.mdAERISCONTROL
Autonomous sail boat with a multiaxial sail control
Parts
109| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C7, C8, C10, C11, C12, C17 |
| 9 | ~ | Custom_Aeris:SJ_Stepper_1-5mm | J17, J18, J20, J22, J25, J26, J28, J30, J31 |
| 8 | Conn_01x04_Socket | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J15, J16, J19, J21, J23, J24, J27, J29 |
| 6 | Conn_01x08_Stepper | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical_SMD_Pin1Left | J2, J3, J4, J8, J9, J10 |
| 6 | Conn_09x16_Stepper | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical_SMD_Pin1Left | J5, J6, J7, J11, J12, J13 |
| 6 | Stepper_Motor_bipolar | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | M1, M2, M3, M4, M5, M6 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R18, R19, R20, R21 |
| 3 | 27 | Resistor_SMD:R_0603_1608Metric | R5, R6, R7 |
| 2 | 0.1µF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C21, C26 |
| 2 | 100K | Resistor_SMD:R_0603_1608Metric | R3, R8 |
| 2 | 12pF | Capacitor_SMD:C_0603_1608Metric | C14, C15 |
| 2 | 4,7µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C19, C22 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C9, C16 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | MountingHole | MountingHole:MountingHole_3.5mm | H2, H4 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | 10µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C20 |
| 1 | 17.4k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 2.2uH 13.2mOhm | Inductor_SMD:L_TDK_VLP8040 | L2 |
| 1 | 220k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12 |
| 1 | 22µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C25 |
| 1 | 2K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 3.3uH | Resistor_SMD:R_0805_2012Metric | L1 |
| 1 | 30k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11 |
| 1 | 33pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C24 |
| 1 | 600 @ 100MHz | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | FB1 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | AP7361C-33E | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | Battery | TerminalBlock:TerminalBlock_Altech_AK300-2_P5.00mm | BT1 |
| 1 | CM4012M00012001 | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | G*** | kibuzzard-67CE323D | kibuzzard-67CE323D |
| 1 | G*** | kibuzzard-67CE3450 | kibuzzard-67CE3450 |
| 1 | G*** | kibuzzard-67CE33A5 | kibuzzard-67CE33A5 |
| 1 | G*** | kibuzzard-67CE3498 | kibuzzard-67CE3498 |
| 1 | G*** | kibuzzard-67CE3487 | kibuzzard-67CE3487 |
| 1 | G*** | kibuzzard-67CE320A | kibuzzard-67CE320A |
| 1 | G*** | kibuzzard-67CE3465 | kibuzzard-67CE3465 |
| 1 | G*** | kibuzzard-67CE34A5 | kibuzzard-67CE34A5 |
| 1 | Green_power | Diode_SMD:D_0805_2012Metric | D1 |
| 1 | RP2350B-QFN80 | Package_DFN_QFN:QFN-80-1EP_10x10mm_P0.4mm_EP3.4x3.4mm_ThermalVias | U2 |
| 1 | Raspberry_Pi_4 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical_SMD | J14 |
| 1 | SMD0805B110TF | Fuse:Fuse_0805_2012Metric | F1 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | SW_BOOTSEL | Button_Switch_SMD:SW_SPST_B3U-1000P | BOOT |
| 1 | SW_RESET | Button_Switch_SMD:SW_SPST_B3U-1000P | RESET |
| 1 | TP_12V | TestPoint:TestPoint_Pad_D4.0mm | 12V |
| 1 | TP_3v3 | TestPoint:TestPoint_Pad_D1.0mm | 3v3 |
| 1 | TP_5V | TestPoint:TestPoint_Pad_D4.0mm | 5V |
| 1 | TP_GND | TestPoint:TestPoint_Pad_4.0x4.0mm | GND |
| 1 | TP_VIN_5V | TestPoint:TestPoint_Pad_D1.0mm | 5V |
| 1 | USB_C_PICO | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 1 | W25Q128JVPIQ | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4mm | U3 |
| 1 | ~ | Package_TO_SOT_SMD:SOT-563 | U6 |
Similar boards
- 4 layers160 × 90 mm
- 2 layers42 × 22 mm
Analog bms
CKalitin/analog-bms
1s2p Li-ion battery module with an analog battery management system (BMS).
58 parts1MIT - 2 layers82 × 70 mm
NODO ACCESO
DavidManzano04/control-acceso-iot
Sistema IoT de control de acceso y asistencia docente con RFID: firmware ESP32 + Hikvision y plataforma web Flask (trabajo de grado UCEVA)
58 parts - 4 layers55.9 × 83.8 mm
Stm32g474board
halherta/stm32g474board
EmbLynx Development board for the stm32G474RE microcontroller
70 partsMIT - 2 layers100 × 100 mm
- 2 layers50.3 × 56.3 mm
CM5IO top
Distaff/RPi_CM_Drone_Board
Source of the CM5-based drone controller used for onboard image processing, communication, and high-level automation. Originally created for IARC2026 (drone engineering competition), used in other competitions as well.
57 parts1MIT - 4 layers45 × 45 mm
Falcon fc
yedidiaSch/FalconDrone
[IN PROGRESS] High-performance flight controller for quadcopters, providing real-time stabilization and attitude control using FreeRTOS and C++ on STM32
60 partsMIT
Questions
How big is the Cerbrum Aeris PCB?
It measures 100 × 92 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Cerbrum Aeris use?
109 parts, built around the W25Q128JVPIQ, AP7361C-33E, SRV05-4 and AO3401A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cerbrum Aeris KiCad files?
From the Jabooby/Aeris-Control repository on GitHub, at the commit this page was made from: the board is Electric/Aeris control electrical plans/Cerbrum_Aeris/Cerbrum_Aeris.kicad_pcb and its schematic Electric/Aeris control electrical plans/Cerbrum_Aeris/Cerbrum_Aeris.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cerbrum Aeris design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).