Skip to the content
2 layers303.8 × 94.2 mmLunar-65-pcb, the printed circuit board in 3D

Lunar-65-pcb

ItzZeNash/Lunar65

A keyboard made for personal use and sounds good, as I dont have a keyboard. 65% for optimal usability.

Size
303.8 × 94.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
152
Nets
107
Pads
730
Tracks, vias
1,312, 135
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Apr 2026
Updated
1 Apr 2026

Overview

Lunar-65-pcb is an open-source printed circuit board by ItzZeNash, from the ItzZeNash/Lunar65 repository on GitHub. It is a 2-layer board of 303.8 × 94.2 mm with 152 parts on 107 nets, routed with 1,312 tracks and 135 vias.

It is built around the ATMEGA32U4-MUR and SRV05-4. Its parts include 67 diodes, 7 capacitors, 4 resistors, 2 ICs and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

Lunar65

A keyboard made for personal use and sounds good, as I dont have a keyboard. 65% for optimal usability. Render/Image image Images of Schem And PCB image image

Build Guide

image image image image image image image image
NoNameSpecQuantity
1Aluminum caseAluminum1
2Main PCBHotswap socket compatible, 1.6 mm thick1
3PlatePolycarbonate, 1.5mm thick1
4PCB foamPoron, 3mm thick1
5Switch foamPolyethylene or Poron, 0.5mm thick1
6Case foamPoron, 1.5mm thick1
7Socket foamPoron, 1.5mm thick1
8O-ringAS568-264-VMQ-A301
9USB-C daughter boardUnified Daughterboard C31
10JST cableJST-SH, 4pin, double-side female connector, reverse direction, 10cm1
11Screwsm2 4mm, for USB-C daughter board4
12Rubber feet(Bumpons)3M SJ5302, diameter 8mm, height 2mm4

Parts

NameSpecQuantity
Key switchCherryMX compatible key switch, 5pins(recommended)67
KeycapCherryMX compatible keycap, 1.75U Shift key(required)67
StabilizerDurock V2, etc6.25U * 1set and 2U * 3set
USB cableThe connector on the keyboard side must be USB-C1
Grease for lubricationKrytox 205g0(recommended)a few grams

Assembly Instructions

  1. Attaching rubber feet
    Rubber feet First attach the rubber feet to the aluminum case so that the bottom of the aluminum case is not scratched.
    Attach the rubber feet according to the engraved circle on the four corners of the back of the aluminum case.

  2. Pasting socket foam
    Pasting socket foam Pasting socket foam is difficult and cannot be redone.
    There are two methods: one is to paste the entire surface and the other is to paste only a portion of the surface.

    Practice
    First, practice several times without peeling off the release paper on the adhesive surface.
    Pasting socket foam Place the socket foam on a flat surface with the adhesive surface facing up.
    Straighten any bent or floating parts.
    Pasting socket foam Hold the four corners with the back side (part mounting surface) of the main PCB facing down.
    Look at the main PCB from directly above, align the notch of the mount post with the main PCB, slowly put it on the foam.

    When pasting the entire surface
    Peel off the release paper on the socket foam, and paste the main PCB and socket foam according to the procedure you practiced.
    Once pasted, it cannot be removed cleanly, so recommend not removing it, even if it is slightly displaced.
    (even if it can be removed, the socket foam will be stretched and the position will not match)

    When pasting only a part
    Peel off only a part of the release paper and paste it.
    The area to peel off is about 10 square mm per place, and the place to peel off is about 7-8 places where the width is not narrow.
    Cut a part of the release paper with scissors and paste the main PCB and socket foam according to the procedure you practiced.

  3. Assembling the stabilizers
    Please refer to this YouTube video.
    Apply a little thick grease to the outside of the stem and the inside of the housing.
    Insert the stem into the housing.
    Apply a little thick grease from the tip of the wire to the part that bends at a right angle.
    Insert the wire into the stem and fit the wire into the housing.

  4. Installing stabilizers
    Installing stabilizers First, insert the side without screw holes into the larger stabilizer mounting holes on the main PCB.
    Next, screw the side with screw holes from the back side of the main PCB.
    Make sure that the stabilizer housing is not lifted off the main PCB and that there is no rattling.

  5. Placing switch foam
    Placing switch foam Place the switch foam on the main PCB.
    Slide the switch foam so that it is under the stabilizer wires.

  6. Placing PCB foam
    Placing PCB foam Place PCB foam on the main PCB in line with the stabilizer position.

  7. Placing plate Placing plate Place the plate on the PCB foam, aligning it with the hole in the key switches.

  8. Lubricating key switches
    Although not required, it is highly recommended to lubricate the key switches to improve the typing feels and sounds.
    Please refer to this YouTube video.

  9. Installing key switches
    Installing key switches Check that the holes in the switch foam align with the key switch pin holes on the main PCB.
    Check that the pins of the key switch are straight and insert the key switch into the main PCB from the top of the plate.
    (Be careful not to insert at an angle, as this may break the pins or damage the sockets)
    Make sure that there are no gaps between the plate and the key switches, and between the key switches and the main PCB, viewed from the side, and that they are evenly installed.

  10. Installing O-ring
    Install O-ring between main PCB and plate.
    Installing O-ring

    Around the backspace and spacebar keys, pass the O-ring through the top surface of the stabilizer, aligning it with the notch in the plate.
    If the O-ring cannot be secured to the top of the stabilizer, proceed as is once it is in place, as it can be adjusted when the main PCB is installed in the case.
    Make sure there is no gap and bend between the main PCB, O-ring and plate when viewed from the side.

  11. Connecting JST cable to USB-C daughter board
    Connecting JST cable to USB-C daughter board Connect JST cable to USB-C daughter board.
    Connecting JST cable to USB-C daughter board Since JST cable connectors have front and back sides, refer to the photo and insert the connector with the side with no exposed terminals facing up.

  12. Installing USB-C daughter board
    Installing USB-C daughter board With the surface of the USB-C daughter board (the side where the components are mounted) facing up, screw it into the center back of the aluminum case with four m2 4mm screws.
    Grab the screws with tweezers to make it easier to screw them in.

  13. Installing case foam
    Installing case foam Align the posts inside the aluminum case with the notches in the case foam, and put the case foam inside the aluminum case.
    Pull the JST cable through the cutout in the case foam.

  14. Connecting JST cable tom main PCB
    Connecting JST cable tom main PCB Insert the JST cable connector into the JST connector (beige color) on the back of the main PCB.
    Connecting JST cable tom main PCB Since JST cable connectors have front and back sides, refer to the photo and insert the connector with the side with no exposed terminals facing up.

  15. Installing main PCB to aluminum case
    Installing main PCB to aluminum case With the back side of the main PCB slightly raised, pass the blocker of the aluminum case between the blocker of the main PCB and the O-ring.
    Lift the entire main PCB slightly and put the O-ring on the front side of the main PCB over the post on the front side of the aluminum case (not visible).
    Gently push the main PCB down until the O-ring lightly touches the post on the aluminum case (not visible).
    O-ring and back space Make sure the O-ring is not rolled up and coming out of the plate.

  16. Installing keycaps
    Installing keycaps Installing the keycaps to the key switches.

  17. Connecting USB cable
    Connecting USB cable Connect your USB cable to the keyboard and PC and now it is completed.

Parts

152
QtyValueFootprintReferences
671N4148Diode_SMD:D_SOD-123D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +51
541uMX_Only:MXOnly-1U-HotswapMX1, MX2, MX10, MX11, MX12, MX13, MX15, MX17, MX18, MX19, MX20, MX21, MX22, MX23, MX24, MX25 +38
51.25uMX_Only:MXOnly-1.25U-HotswapMX59, MX60, MX61, MX63, MX64
30.1uCapacitor_SMD:C_0805_2012MetricC1, C2, C3
21.5uMX_Only:MXOnly-1.5U-HotswapMX16, MX29
21.75uMX_Only:MXOnly-1.75U-HotswapMX31, MX56
210kResistor_SMD:R_0805_2012MetricR1, R4
22.25uMX_Only:MXOnly-2.25U-HotswapMX43, MX45
222Resistor_SMD:R_0805_2012MetricR2, R3
222pCapacitor_SMD:C_0805_2012MetricC5, C6
110uCapacitor_SMD:C_0805_2012MetricC4
116MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
11uCapacitor_SMD:C_0805_2012MetricC7
12uMX_Only:MXOnly-2U-HotswapMX14
1500mAFuse:Fuse_1206_3216MetricF1
16.25uMX_Only:MXOnly-6.25U-Hotswap-ReversedStabilizersMX62
1ATmega32U4-MURPackage_DFN_QFN:QFN-44-1EP_7x7mm_P0.5mm_EP5.2x5.2mmU2
1AVR-ISP-6mikeneko:ISPJ2
1JST SH 4-pinConnector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ1
1ResetButton_Switch_SMD:SW_SPST_TL3342SW1
1SRV05-4Package_TO_SOT_SMD:SOT-23-6U1

Similar boards

  • 2 layers14.2 × 36 mmMega nrf24 usb, the printed circuit board in 3D

    Mega nrf24 usb

    douglaslyon/pentester

    This is a pentration testing system using rfmicro and a custom nrf24l01 shield

    14 parts2GPL-3.0
  • 2 layers22.9 × 26.8 mmBase 32u, the printed circuit board in 3D

    Base 32u

    EmulationOnline/chiplab

    The Chiplab is a platform for researching behavior of digital integrated circuits. It includes provides instrumentation to run programs against real hardware and observe the results.

    22 parts2BSD-4-Clause
  • 2 layers33 × 17.8 mmPro micro c, the printed circuit board in 3D

    Pro micro c

    joshajohnson/sea-micro

    Arduino Pro Micro, with a USB Type-C Connector

    25 parts77
  • 2 layers208.8 × 396.9 mmFerris, the printed circuit board in 3D

    Ferris

    pierrechevalier83/ferris

    A low profile split keyboard designed to satisfy one single use case elegantly

    145 parts1.3k
  • 2 layers142.5 × 101 mmHillside46, the printed circuit board in 3D

    Hillside46

    mmccoyd/hillside

    Family of split ergonomic keyboards with three rows of six or five keys and a generous thumb arc

    92 parts448MIT
  • 4 layers40.6 × 17.8 mmPD Micro, the printed circuit board in 3D

    PD Micro

    ryan-ma/PD_Micro

    USB-C PD3.0 PPS on ATMega32U4 Arduino board

    61 parts439MIT
  • 2 layers139.1 × 107.7 mmLotus58 Glow 151, the printed circuit board in 3D

    Lotus58 Glow 151

    TweetyDaBird/Lotus-58-Classic

    A split ergo linear keyboard derived from the Lily58 family

    153 parts390
  • 4 layers70 × 54 mmPicoLab, the printed circuit board in 3D

    PicoLab

    CoretechR/PicoLab

    Web-GUI Embedded Multitool

    285 parts327GPL-3.0

Questions

How big is the Lunar-65-pcb PCB?

It measures 303.8 × 94.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lunar-65-pcb use?

152 parts, built around the ATMEGA32U4-MUR and SRV05-4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lunar-65-pcb KiCad files?

From the ItzZeNash/Lunar65 repository on GitHub, at the commit this page was made from: the board is Kicad Files/lunar-65-pcb.kicad_pcb and its schematic Kicad Files/lunar-65-pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lunar-65-pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask ItzZeNash before reusing the design.