Skip to the content
2 layers150 × 100 mmIPC101, the printed circuit board in 3D

Iron Pine IPC-101 — modular operator control-panel PCB for IPC-100-based products, providing physical controls, navigation, status indication, and display interfacing.

Size
150 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
27
Pads
85
Tracks, vias
114, 56
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
1 Sep 2026
Updated
30 Sep 2026

Overview

IPC101 is an open-source printed circuit board by IronPineOutdoors, from the IronPineOutdoors/IPC101 repository on GitHub. It is a 2-layer board of 150 × 100 mm with 24 parts on 27 nets, routed with 114 tracks and 56 vias.

Its parts include 4 resistors, 4 connectors, 3 switches, 2 capacitors and 1 IC.

README

hardware/kicad/README.md

IPC-101 Rev C KiCad Source

This directory contains the fabrication-oriented Rev C operator-control board for the Crosswind control-panel replacement.

Rev C layout

  • Board outline: 150 x 100 mm, matching the Rev C faceplate.
  • OLED: left-side 2.42-inch Hosyond/SSD1309 mechanical pattern. The display mounts to the faceplate and plugs into IPC-101 J2; J4 carries the same isolated five-wire branch to IPC-100 J6 (OLED_VCC, GND, SDA, SCL, RESET).
  • Navigation: Adafruit 504 five-way switch at the right side of the display row.
  • Lower controls: ARM at left and PULL at right.
  • Indicator: PCB-mounted 5 mm common-anode RGB LED centered between the lower controls and display row.
  • Power-switch region: mechanically reserved only; no cutout or footprint is committed until the rated switch is selected.

The IPC-101 board connects to IPC-100 through J1 for keypad +3V3, GND, SDA, and SCL, through J4 for the dedicated OLED branch, and through J3 for isolated STOP. J2 is the local OLED harness output. The J2/J4 copper pass-through does not join the J1 keypad branch.

Electrical implementation

  • U1: TCA8418 keypad/GPIO controller in TI RTW-24 QFN.
  • SW1: ARM; SW2: PULL; SW3: LEFT/RIGHT/UP/DOWN/SELECT.
  • D1: 5 mm common-anode RGB LED.
  • R2/R3/R4: 1 kOhm current-limiting resistors.
  • RGB GPIO assignment: COL6/pad 15 red, COL7/pad 16 green, COL8/pad 17 blue.
  • Two copper layers with 0.20 mm signal tracks, 0.15 mm clearance, and 0.50/0.30 mm vias.
  • F.Cu +3V3 plane and B.Cu ground plane with explicit island stitching.

generate_rev_c_pcb.py reproducibly rebuilds the placed and routed geometry from the embedded footprints. Run it with KiCad's bundled Python, then refill zones and rerun DRC if any placement or routing is edited interactively.

Validation

  • IPC101_DRC.rpt: full KiCad DRC, 0 violations and 0 unconnected items.
  • IPC101_ERC.rpt: KiCad error-level ERC, 0 violations.
  • IPC101_RevC_3D.png: top-side KiCad render for placement review.
  • IPC101_RevC.net.xml: exported schematic netlist for parity/review tooling.

Before ordering a production quantity, print the Rev C faceplate and both caps, assemble one PCB, verify the Adafruit 504 physical pin orientation, and continuity-check both OLED harnesses against the received module and the documented J2/J4 pinouts.

Solder-mask correction (2026-09-07)

The 29 PTH component pads now explicitly include both F.Mask and B.Mask. Copper routing and drill geometry are unchanged. generate_rev_c_pcb.py restores these layers for cloned as well as newly created PTH pads. Use the replacement IPC101_RevC_MaskFix_Gerbers.zip; the earlier package had an empty bottom mask and omitted top openings for the PTH pads. The fabrication export script audits source pad layers and every solderable pad centre in the archived mask files.

Parts

24
QtyValueFootprintReferences
4H1, H2, H3, H4
1+3V3TP1
1100nFC1
110k RESETR1
11k BLUER4
11k GREENR3
11k REDR2
14.7uFC2
15MM RGB COMMON ANODED1
1ADAFRUIT 504 - VERIFY PIN MAPSW3
1ARM B3F-4055SW1
1GNDTP2
1HOSYOND 2.42in SSD1309 - 5 WIRE J6 HARNESSDS1
1IPC-100 J10J1
1IPC-100 J6 OLED INPUTJ4
1IPC-100 J8A STOPJ3
1OLED HARNESS OUTPUTJ2
1PULL B3F-4055SW2
1SCLTP4
1SDATP3
1TCA8418RTWRU1

Similar boards

  • 2 layers56 × 65 mmSeaTalk1, the printed circuit board in 3D

    SeaTalk1

    dotnet/iot

    This repo includes .NET Core implementations for various IoT boards, chips, displays and PCBs.

    24 parts2.4kMIT
  • 2 layers26.2 × 45.5 mmPL18 multiprotocol, the printed circuit board in 3D

    PL18 multiprotocol

    pascallanger/DIY-Multiprotocol-TX-Module

    Multiprotocol TX Module (or MULTI-Module) is a 2.4GHz transmitter module which controls many different receivers and models.

    24 parts1.9kGPL-3.0
  • 2 layers58 × 35.5 mmHat, the printed circuit board in 3D

    Hat

    menloresearch/asimov-1

    v1 of Asimov, an open-source humanoid robot

    24 parts1.4kCERN-OHL-S-2.0
  • 2 layers21.6 × 19.5 mmMicron Logo LED, the printed circuit board in 3D

    Micron Logo LED

    DraftShift/StealthChanger

    Tool changing system for Vorons and other front mount printer motion systems, not just stealthburner.

    24 parts1.2kGPL-3.0
  • 2 layers158 × 11 mmRainbow Matchstick, the printed circuit board in 3D

    Rainbow Matchstick

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    24 parts1.1kGPL-3.0
  • 2 layers85.6 × 54 mmTRACED wio1262-carrier, the printed circuit board in 3D

    TRACED wio1262-carrier

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    24 parts915
  • 2 layers36 × 20 mmCombined, the printed circuit board in 3D

    Combined

    adamb314/ServoProject

    Getting the most out of your hobby servo

    24 parts545

Questions

How big is the IPC101 PCB?

It measures 150 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the IPC101 use?

24 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the IPC101 KiCad files?

From the IronPineOutdoors/IPC101 repository on GitHub, at the commit this page was made from: the board is hardware/kicad/IPC101.kicad_pcb and its schematic hardware/kicad/IPC101.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the IPC101 design in my own project?

Its repository states no licence, so its author keeps all rights: ask IronPineOutdoors before reusing the design.