Skip to the content
2 layersProto panel cm4-driver, the printed circuit board in 3D

Proto panel cm4-driver

infopcgood/proto-panel-cm4-driver

CM4 driver board for the proto-panel

Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
211
Pads
355
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 9.0 (file 20241229)
Created
14 Mar 2026
Updated
16 Mar 2026

Overview

Proto panel cm4-driver is an open-source printed circuit board by infopcgood, from the infopcgood/proto-panel-cm4-driver repository on GitHub. It is a 2-layer board with 24 parts on 211 nets.

It is built around the TXS0108EPW. Its parts include 16 resistors, 4 capacitors, 3 ICs and 1 connector. It belongs with the computers and single-board computers boards of this library.

Main components

1

README

README.md

proto-panel-cm4-driver

CM4 driver board for the proto-panel

Parts

24
QtyValueFootprintReferences
16330Resistor_SMD:R_0603_1608MetricR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16
4100nFCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4
2TXS0108EPWPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU2, U3
1Bus_M.2_Socket_Mm2-library:TE_1-2199230-5J3
1CM4108032cm4-library:MODULE_CM4108032U1

Similar boards

  • 4 layers68.6 × 53.3 mmIcezum, the printed circuit board in 3D

    Icezum

    FPGAwars/icezum

    :star2: IceZUM Alhambra: an Arduino-like Open FPGA electronic board

    218 parts357GPL-3.0
  • 2 layers94.5 × 74.4 mmAx58100-stm32-ethercat, the printed circuit board in 3D

    Ax58100-stm32-ethercat

    MetalMusings/MyOwnEtherCATDevice

    Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.

    184 parts93
  • 4 layers80 × 100 mmBaseboard, the printed circuit board in 3D

    Baseboard

    NVIDIA-AI-IOT/my-jetson-nano-baseboard

    An open source Jetson Nano baseboard and tools to design your own.

    240 parts91
  • 4 layers80 × 73.8 mmESP32-Bit Pirate Dock, the printed circuit board in 3D

    ESP32-Bit Pirate Dock

    AndreiVladescu/ESP32-Bit-Pirate-Hardware

    Carrier breaker-board for the ESP32-S3 Devkit. Works great with the ESP32-Bit-Pirate firmware.

    49 parts85CERN-OHL-W-2.0
  • 4 layers42.8 × 36.8 mmDriver board, the printed circuit board in 3D

    Driver board

    blazer82/FT81x_Arduino_Driver

    FT81x on ST7701S Arduino Driver

    49 parts59MIT
  • 2 layers81.3 × 30.9 mmISABlaster, the printed circuit board in 3D

    ISABlaster

    scrapcomputing/ISABlaster

    A software-defined ISA card powered by a Raspberry Pi Pico

    24 parts53GPL-2.0
  • 4 layers29 × 50.3 mmToshiba hvac esp32, the printed circuit board in 3D

    Toshiba hvac esp32

    florianbrede-ayet/esphome-toshiba-hvac-controller

    ESPhome component & hardware to control Toshiba & Carrier HVAC units with WIFI interface

    7 parts38MIT
  • 4 layers65 × 100 mmUBMS-2, the printed circuit board in 3D

    UBMS-2

    grokicad/grokicad

    Grok powered schematic intelligence for your kicad repositories

    246 parts28

Questions

What parts does the Proto panel cm4-driver use?

24 parts, built around the TXS0108EPW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Proto panel cm4-driver KiCad files?

From the infopcgood/proto-panel-cm4-driver repository on GitHub, at the commit this page was made from: the board is proto-panel-cm4-driver.kicad_pcb and its schematic proto-panel-cm4-driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Proto panel cm4-driver design in my own project?

Its repository states no licence, so its author keeps all rights: ask infopcgood before reusing the design.