

Eco pcb combined
Source files for the ECO Sensor Box
- Size
- 110 × 110 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 97
- Nets
- 75
- Pads
- 418
- Tracks, vias
- 872, 170
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 17 Apr 2020
- Updated
- 12 Nov 2021
Overview
Eco pcb combined is an open-source printed circuit board by inetrg, from the inetrg/ECO repository on GitHub. It is a 2-layer board of 110 × 110 mm with 97 parts on 75 nets, routed with 872 tracks and 170 vias.
It is built around the SI2329DS. Its parts include 28 capacitors, 27 resistors, 9 connectors, 7 ICs and 3 transistors. It belongs with the sensors and measurement boards of this library.
Main components
1README
measurement/README.mdRIOT Energy-Harvesting Monitor using INA226
This module can be used to measure voltage and current of a connected load. It comes with three different measurement ranges that can be freely configured by mounting different shunt resistors. Depending on your use case you can switch between the measurement ranges with the slider switches. The configuration of the board hosts jumpers to configure four different I2C slave addresses.
BOM
Below is the bill of materials for equipping the pcb. Obviously you can choose to use other parts as long as they have the same footprint and properties. For the lazy ones: you may want to look at this pre-filled shopping cart at Mouser which contains all the parts needed to equip a single PCB.
| Component identifier | Part | cnt. | Mouser Link |
|---|---|---|---|
| U1 | INA226 VSSOP-10 | 1 | 595-INA226AIDGSR |
| SW1, SW2, SW3 | Slide Switches SPDT 4A 125V | 3 | 642-25136NAH |
| R1 | 0.1 Ohm 0.5% current sense resistor | 1 | 660-SLW1TTER100D |
| R2 | 1 Ohm 0.5% current sense resistor | 1 | 660-SL1TTE1R00D |
| R3 | 2 Ohm 0.5% current sense resistor | 1 | 660-SL1TTE2R00D |
| C1 | 0.1 µF Capacitor | 1 | 77-VJ0805Y104JXXAC |
| - | Jumper | 2 | 151-8010-E |
| X1, X2, X3, X4 | Fixed Terminal screw clamp 2P | 4 | 504-EM366002 |
| JP1, JP1 | 1x3 Pin Header 2.54mm pitch male | 2 | 538-22-28-4031 |
Configuration
With the jumpers on JP1 and JP2 you can configure the I2C slave address according to the following table.
| JPA1 | JPA0 | A1 Pin | A0 Pin | Address |
|---|---|---|---|---|
| 1 2-3 | 1 2-3 | GND | GND | 0x40 |
| 1 2-3 | 1-2 3 | GND | VS | 0x41 |
| 1-2 3 | 1 2-3 | VS | GND | 0x44 |
| 1-2 3 | 1-2 3 | VS | VS | 0x45 |
(c) by Michel Rottleuthner
The files in this folder are licensed under a Creative Commons Attribution 4.0 International License.
You should have received a copy of the license along with this work. If not, see .
Parts
97| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100kΩ | Resistor_SMD:R_0805_2012Metric | R3, R8, R12, R13, R14, R15, R26, RPD1, RPU1 |
| 6 | 10µF | Capacitor_SMD:C_0805_2012Metric | C2, C11, C14, C20, C21, C22 |
| 6 | Jumper_2_Bridged | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1, JP4, JP5, JP6, JP7, JP8 |
| 6 | MountingHole | eco_custom_footprints:MountingHole_8.1mm_M8_Pad_Via | H1, H2, H3, H4, H5, H6 |
| 5 | 1µF | Capacitor_SMD:C_0805_2012Metric | C5, C7, C12, C13, C16 |
| 4 | 0Ω | Resistor_SMD:R_0805_2012Metric | R18, R19, R21, R22 |
| 4 | 100nF | Capacitor_SMD:C_0805_2012Metric | C15, C17, C19, C23 |
| 4 | 50F-100F | Capacitor_THT:CP_Radial_D18.0mm_P7.50mm | C1, C3, C6, C8 |
| 3 | 330Ω | Resistor_SMD:R_0805_2012Metric | R4, R7, R25 |
| 3 | 47µF | Capacitor_Tantalum_SMD:CP_EIA-3216-10_Kemet-I | C26, C27, C28 |
| 3 | Si2329DS | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 1MΩ | Resistor_SMD:R_0805_2012Metric | R1, R16 |
| 2 | 2.2µH | Inductor_SMD:L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L2, L3 |
| 2 | 22µF | Capacitor_SMD:C_1206_3216Metric | C24, C25 |
| 2 | 36.5kΩ | Resistor_SMD:R_0805_2012Metric | R23, R24 |
| 2 | 390kΩ | Resistor_SMD:R_0805_2012Metric | R2, R5 |
| 2 | 4.7kΩ | Resistor_SMD:R_0805_2012Metric | R9, R10 |
| 2 | 4.7µF | Capacitor_SMD:C_0805_2012Metric | C10, C18 |
| 2 | 500kΩ | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV_VMPP1, RV_VO1 |
| 2 | Conn_01x04_Female | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J10, J11 |
| 2 | Conn_02x19_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x19_P2.54mm_Vertical | J7, J9 |
| 2 | JP2E | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | J_A1, J_A2 |
| 2 | Jumper_NC_Small | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2, JP3 |
| 2 | TPS63900 | Package_SON:WSON-10-1EP_2.5x2.5mm_P0.5mm_EP1.2x2mm | U6, U7 |
| 1 | 0.27Ω | Resistor_SMD:R_1206_3216Metric | R17 |
| 1 | 1.1MΩ | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 10µH | Inductor_SMD:L_TDK_SLF6045 | L1 |
| 1 | 1nF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 2.5MΩ | Resistor_SMD:R_0805_2012Metric | R20 |
| 1 | 22pF | Capacitor_SMD:C_0805_2012Metric | C9 |
| 1 | BOB-00544 | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J6 |
| 1 | Conn_01x04 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J5 |
| 1 | Conn_01x05 | eco_pcb_combined:JST_B5B_ZR | J1 |
| 1 | Conn_Coaxial | Connector_Coaxial:MMCX_Molex_73415-0961_Horizontal_1.6mm-PCB | J8 |
| 1 | DORJI_DRF1276G | eco_custom_footprints:DRF1276G | U4 |
| 1 | INA226INA226AIDGS | Package_SO:VSSOP-10_3x3mm_P0.5mm | U5 |
| 1 | L96 | eco_custom_footprints:XCVR_L96 | U2 |
| 1 | LTC3105 | Package_SO:MSOP-12_3x4mm_P0.65mm | U1 |
| 1 | Littlefuse_TVS_SMF3.3 | Diode_SMD:D_SOD-123F | D1 |
| 1 | Logo | logos:RIOT_ECO_HAW_OSHW_straight | LOGO1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J2 |
| 1 | TPS7A0230PDBVR | Package_TO_SOT_SMD:SOT-23-5 | U3 |
More from inetrg/ECO
4- 2 layers156 × 116 mm

- 2 layers44.5 × 53.8 mm

- 2 layers22.3 × 39.6 mm

- 2 layers35 × 44.8 mm

Similar boards
- 2 layers142 × 58 mm

- 2 layers99.8 × 99.8 mm

- 2 layers380 × 45 mm

AddOnC
freeDSP/freeDSP-aurora
freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth
97 parts226CC-BY-SA-4.0 - 2 layers100 × 110 mm

Kicad control board smt
matthewcieplak/super-sixteen
Code and schematics for the Super Sixteen Eurorack sequencer
97 parts171 - 2 layers40 × 100 mm

Front prototype
ZeroPhone/ZeroPhone-PCBs
PCB files for ZeroPhone - for gerbers and schematics, go to "Releases" tab!
97 parts148GPL-3.0 - 2 layers301 × 77 mm

- 2 layers100 × 95 mm

- 2 layers66 × 62 mm

Ch570aaonlyswadge
cnlohr/cnhardware
My dumping grounds for all my kicad projects and random hardware bringup.
97 parts114
Questions
How big is the Eco pcb combined PCB?
It measures 110 × 110 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Eco pcb combined use?
97 parts, built around the SI2329DS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Eco pcb combined KiCad files?
From the inetrg/ECO repository on GitHub, at the commit this page was made from: the board is eco_pcb_combined/eco_pcb_combined.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Eco pcb combined design in my own project?
Its repository states no licence, so its author keeps all rights: ask inetrg before reusing the design.