4 layers260 × 260 mm
2 layers72 × 90 mm
Wind breakout
idlehandsdev/wind_breakout14Breakout board for all Adafruit Feather series boards.
- Size
- 72 × 90 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 45
- Pads
- 296
- Tracks, vias
- 85, 1
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 13 May 2019
- Updated
- 10 Jun 2019
Overview
Wind breakout is an open-source printed circuit board by idlehandsdev, from the idlehandsdev/wind_breakout repository on GitHub. It is a 2-layer board of 72 × 90 mm with 58 parts on 45 nets, routed with 85 tracks and 1 via.
It is built around the D12. Its parts include 44 connectors, 4 switches and 2 resistors. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
Main components
1README
README.mdWIND Breakout
wind makes the feather fly.
WIND is a breakout board for the Adafruit Feather Series to make it easier to fly wire and put together a project with little to no soldering.
It contains a battery holder for a 18650(I hate loose batteries!), a few buttons, and 5 pin headers for each pin(plus a proto section). There is a power switch connected to the Enable pin(shuts off the regulator), and a voltage divider to the A0 analog for monitoring battery voltage.
This makes it easy to mount in a housing, and wire up different sensors you want to test.
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | Proto | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J29, J30, J31, J32, J33, J34, J35, J36, J37, J38, J39, J40, J41, J42, J43, J44 |
| 3 | SW_Push | Button_Switch_SMD:SW_SPST_B3SL-1022P | SW2, SW3, SW4 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 18650 | Battery:BatteryHolder_Keystone_1042_1x18650 | BT1 |
| 1 | 200k | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | A0 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | A1 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J9 |
| 1 | A2 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J16 |
| 1 | A3 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J23 |
| 1 | A4 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J3 |
| 1 | A5 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J10 |
| 1 | AREF | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J15 |
| 1 | D0 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J11 |
| 1 | D1 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J18 |
| 1 | D10 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J20 |
| 1 | D11 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J13 |
| 1 | D12 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6 |
| 1 | D13 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J26 |
| 1 | D5 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J14 |
| 1 | D6 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J7 |
| 1 | D9 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J27 |
| 1 | EN | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J12 |
| 1 | EXT | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J25 |
| 1 | GND | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J22 |
| 1 | LOGO | logos:SH_Logo_cu | G*** |
| 1 | LOGO | logos:SH_Logo | G*** |
| 1 | LOGO | logos:featherfly | G*** |
| 1 | LOGO | logos:windlogo | G*** |
| 1 | LOGO | logos:youtubesh | G*** |
| 1 | MISO | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | MOSI | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J24 |
| 1 | RESET | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | SCK | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J17 |
| 1 | SCL | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J21 |
| 1 | SDA | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J28 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_CK-JS102011SAQN | SW1 |
| 1 | VAL** | Adafruit_FeatherWing:PCB_FeatherWing_silk | PCB** |
| 1 | VBAT | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | VBUS | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J19 |
| 1 | VCC | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J8 |
| 1 | batt_jmp | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
Questions
How big is the Wind breakout PCB?
It measures 72 × 90 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wind breakout use?
58 parts, built around the D12. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wind breakout KiCad files?
From the idlehandsdev/wind_breakout repository on GitHub, at the commit this page was made from: the board is PCB/wind_breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wind breakout design in my own project?
Its repository states no licence, so its author keeps all rights: ask idlehandsdev before reusing the design.
Similar boards
- 2 layers285.1 × 94.3 mm
- 2 layers140.4 × 111.9 mm
- 2 layers99.8 × 100.8 mm
- 4 layers100 × 43.3 mm
Pdp-11-colour
ashlin4010/pdp-11.40-mini-panel
Included in this repository are the PCB files to make a miniature PDP-11/40 front panel. The board uses a XIAO nrf52840 dev board. No software has been written yet.
96 parts2MIT - 2 layers242.6 × 154.9 mm
- 2 layers
- 2 layers71.6 × 94.2 mm
Buta board v1
azerimaker/ButaBoard
This repo contains all the necessary design and fabrication files for the ButaBoard.
81 parts