

Open source Thinkpad T420 battery design
- Size
- 74.3 × 52.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 57
- Pads
- 204
- Tracks, vias
- 606, 41
- Pours
- 14
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 Aug 2020
- Updated
- 14 May 2022
Overview
Bq3060 is an open-source printed circuit board by iam4722202468, from the iam4722202468/ThinkpadBattery repository on GitHub, published under the MIT licence. It is a 2-layer board of 74.3 × 52.8 mm with 70 parts on 57 nets, routed with 606 tracks and 41 vias.
It is built around the BQ29412DCT, BQ3060PW and MBR0560-TP, with the SI4435DYTRPBF, SI1023X and NDS351AN among its other parts. Its parts include 30 resistors, 22 capacitors, 6 transistors, 5 connectors and 3 diodes. It belongs with the power boards of this library.
Main components
6BQ29412DCT
MSOP-8-40℃~+110℃ 2~4 4.45V 4V~25V MSOP-8 Battery Management ROHSTexas InstrumentsBattery ManagementBQ3060PW
TSSOP-24-40℃~+85℃ 2~4 3.8V~25V 441uA Lithium Battery Protection IC、Monitoring IC SMBus Support Support TSSOP-24 Battery Management ROHSTexas InstrumentsBattery ManagementMBR0560-TP
SOD-1231 Independent 200uA@60V 5.5A 500mA 60V 700mV@500mA SOD-123 Schottky Diodes ROHSMicro Commercial ComponentsSchottky DiodesSI4435DYTRPBF
SO-8-55℃~+150℃ 1 P-Channel 1V 2.32nF 2.5W 20mΩ@10V 270pF 30V 390pF 60nC 8A P-Channel ±20V SO-8 MOSFETs ROHSInfineon TechnologiesMOSFETsSI1023X
SOT-563-6-55℃~+150℃ 1.5nC@4.5V 145mW 2 P-Channel 2.7Ω@1.8V 20V 350mA 450mV P-Channel ±6V SOT-563-6 MOSFETs ROHSVishay IntertechnologyMOSFETsNDS351AN
SOT-23MOSFETsTECH PUBLIC
README
README.mdThinkpadBattery
Open source Thinkpad battery design
What is this?
This is a fully open source laptop battery design. The design uses an attiny85, which can reply to the T420 motherboard's SMBUS requests.
Setup
Configurable Constants
- BATTERY_CAPACITY | Your battery capacity in mAH
- V_HIGH | The highest output voltage of your battery, normally 12.6v
- V_LOW | The cutoff for when the battery will stop working, normally around 10.8v
Creating your own
Parts Needed
- Arduino Uno/Mega (for programming the attiny85, Mega needs different pin assignment)
- 12v Lithium-Ion battery pack
- 3S Lithium-Ion BMS (it might be possible to use the existing bms if specification is available but communication needs to be implemented)
- Components from schematic
- PCB from schematic
Once you have all these parts, assemble the pcb and attach a BMS to your battery pack. Solder the 12v battery output/input to the large pads on the pcb, then program the attiny85 with the included ino file. The output pins at the bottom of the PCB are a 1-1 mapping of the motherboard pin input.
Debugging
- The laptop won't supply power to the board unless it detects there's a battery attached, meaning if you plug the board in to the battery without having an external battery to power it, it won't work.
Libraries
Use the ATTinyCore for compiling. Without it, Wire.h won't work.
Limitations
Voltage Reading / Remaining battery
Currently remaining battery %'s aren't exact because I'm assuming there is a linear coorelation between voltage and capacity (Which is wrong). This is probably fixable using a battery gas gauge, I'll have to investiage more.
MCU Power Consumption
By design, the MCU will always be on as long as a battery is connected to it. This can cause the battery to slowly run out of power if it isn't connected to a laptop. A potential fix could be to implement a low power mode for the attiny, or have a seperate disconnect switch for the battery power on the battery pack itself.
3D Printable Case for T420 only
The case for the cells has been completed. The case model and stl files are included in /model
Future Plans
iam4722202468 - Design and manufacture a PCB with current,voltage and battery capacity measuring capabilities, an easily programmable microcontroller, and a 3s balanced charger
pj1976 - Find a bms that would fit, or try to talk with bq29312pw that was in the original pack
Credits
iam4722202468 - Initial work, T420 9 cell model
pj1976 - Added support for R50
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 0.1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C5, C6, C7, C8, C10, C12, C13, C14, C15, C16, C18, C19 |
| 9 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8, R9 |
| 4 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R15, R16, R29, R31 |
| 4 | 100 2W | Resistor_SMD:R_2512_6332Metric_Pad1.52x3.35mm_HandSolder | R10, R11, R12, R13 |
| 3 | 1.0uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C11, C17, C20 |
| 3 | 5.1K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R21, R22, R24 |
| 3 | MBR0560-TP | Diode_SMD:D_SOD-123 | D1, D2, D3 |
| 3 | SI4435DYTRPBF | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q4, Q5, Q6 |
| 2 | 100pF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C21, C22 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | RT1, RT2 |
| 2 | 200 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R27, R28 |
| 2 | 220K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R17, R19 |
| 2 | 3M | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R20, R25 |
| 2 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2, J3 |
| 2 | Si1023x | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q1, Q2 |
| 1 | 0.005 75ppm | Resistor_SMD:R_2512_6332Metric_Pad1.52x3.35mm_HandSolder | R14 |
| 1 | 0.22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C9 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R30 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R18 |
| 1 | 301 1W | Resistor_SMD:R_2512_6332Metric_Pad1.52x3.35mm_HandSolder | R23 |
| 1 | BQ29412DCT | footprints:SN74LVC2G241_DCT_8 | U1 |
| 1 | BQ3060PW | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U2 |
| 1 | Conn_01x02_Male | Connector_Wire:SolderWirePad_1x02_P7.62mm_Drill2mm | J5 |
| 1 | Conn_01x03_Male | Connector_Wire:SolderWirePad_1x03_P5.715mm_Drill2mm | J4 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J1 |
| 1 | NDS351AN | Package_TO_SOT_SMD:SOT-23 | Q3 |
More from iam4722202468/ThinkpadBattery
1- 2 layers17.8 × 26 mm

Similar boards
- 2 layers120.1 × 58.9 mm

- 2 layers104 × 57.9 mm

- 2 layers61.8 × 73.2 mm

- 2 layers47.3 × 52.8 mm

- 2 layers141 × 88 mm

ErgoSNM Keyboard Right Prototype 1
siderakb/ergo-snm-keyboard
ErgoSNM is a split ergonomic keyboard integrated with trackball, wireless is in beta
70 parts172CERN-OHL-P-2.0 - 2 layers38.1 × 101.6 mm

- 2 layers90 × 100 mm

- 2 layers90 × 140 mm

Drumkid
mattybrad/drumkid
Version 4 was the first successful working design, with full code, schematics, Gerbers, etc available on GitHub.
70 parts137
Questions
How big is the Bq3060 PCB?
It measures 74.3 × 52.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Bq3060 use?
70 parts, built around the BQ29412DCT, BQ3060PW, MBR0560-TP and SI4435DYTRPBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bq3060 KiCad files?
From the iam4722202468/ThinkpadBattery repository on GitHub, at the commit this page was made from: the board is KiCad/bq3060/bq3060.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bq3060 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).