

Fib PCB
PCB designed to transmit and replicate electrical signals over fiber optic links.
- Size
- 44.5 × 46 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 33
- Pads
- 180
- Tracks, vias
- 313, 27
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 May 2025
- Updated
- 30 May 2025
Overview
Fib PCB is an open-source printed circuit board by hulonoj, from the hulonoj/FiberOpticBoard repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 44.5 × 46 mm with 55 parts on 33 nets, routed with 313 tracks and 27 vias.
It is built around the XC2C64A-5VQG44C, ERJ3EKF1002V and RC0603JR-070RL, with the CC0603KRX7R7BB104 among its other parts. Its parts include 19 capacitors, 10 resistors, 4 inductors, 2 ICs and 1 connector. It belongs with the FPGA and CPLD boards of this library.
Main components
4XC2C64A-5VQG44C
VQFP-44(10x10)Supports hot swap VQFP-44(10x10) Programmable Logic Device (CPLDs/FPGAs) ROHSAMD/XILINXProgrammable Logic Device (CPLDs/FPGAs)ERJ3EKF1002V
0603-55℃~+155℃ 100mW 10kΩ 75V Thick Film Resistor ±1% ±100ppm/℃ 0603 Chip Resistor - Surface Mount ROHSPanasonicChip Resistor - Surface MountRC0603JR-070RL
UncategorisedUnknown makerCC0603KRX7R7BB104
0603100nF 16V X7R ±10% 0603 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMT
README
README.mdFiber Optic Based Signal Extender
A high-speed hardware system designed to transmit and replicate electrical signals over long distances using fiber optics with minimal latency.
Overview
This project consists of two custom PCB systems designed for high-speed signal replication across fiber:
- Transmitter/Receiver Board: FPGA-based PCB for protocol-agnostic electrical signal replication over fiber with ~30 ns latency.
- Motor Controller Board: STM32-based H-Bridge driver interfaced via I2C through the fiber optic system.
The design demonstrates a full end-to-end communication system without electrical coupling, ideal for applications where noise isolation or long-distance communication is required. This was my capstone project for my Advanced Embedded Systems course at the University of Michigan, and was worked on by a team of five. I contributed heavily and mainly to the hardware development and testing, while collaborating closely with teammates on software and system integration and validation.
Features
- Custom fiber optic communication protocol with latency < 30 ns
- Supports arbitrary digital signal formats (protocol-agnostic)
- Isolated end-to-end data replication
- STM32 motor controller with I2C command input
- Integrated H-Bridge for direct motor control
Photos
Fiber Optic Board mounted on top of a motor controller board.
Half-Assembled Fiber Optic Board
Schematic
Layout
Poster Describing Project

Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 10uF 0603 | Vault:FP-C0603C106M9PACTU-MFG | C1, C7, C8, C9, C11, C12, C14, C15, C17, C18 |
| 8 | ERJ3EKF1002V | Vault:RESC1609X55X30LL15T15 | R1, R3, R4, R6, R8, R10, R12, R16 |
| 7 | RC0603JR-070RL | Vault:RESC1608X55X25ML10T15 | 0, 1, 2, 3, 4, 5, R7 |
| 6 | Header 2 | Miscellaneous Connectors:HDR1X2 | 3V3, I2C, LB, P6, PR, RST |
| 5 | 100nF 0603 | Vault:CAPC1608X90X35LL15T15 | C2, C10, C13, C16, C19 |
| 4 | 1uH | Vault:FP-LBMF1608-0_8-0_2-MFG | L1, L2, L3, L4 |
| 4 | CC0603KRX7R7BB104 | Vault:FP-CC0603-DA-MFG | C3, C4, C5, C6 |
| 2 | 4.7k 0603 | Vault:FP-CRCW0603-e3-IPC_A | R14, R15 |
| 2 | RX | FiberTranscievers:PCBComponent_1 | LI, PI |
| 2 | TX | FiberTranscievers:PCBComponent_1 | LO, PO |
| 1 | Header 4 | Miscellaneous Connectors:HDR1X4 | P4 |
| 1 | Header 6 | Miscellaneous Connectors:HDR1X6 | JTAG1 |
| 1 | LD1117AS18TR | Vault:SOT-223_L | U2 |
| 1 | Oscillator | Oscillator:Oscillator | O1 |
| 1 | XC2C64A-5VQG44C | Vault:VQG44_M | U1 |
Similar boards
- 4 layers118 × 60 mm

- 4 layers80 × 40 mm

ThreeMan HW
znibb/ThreeMan_HW
According to Hardware Semantic Versioning (MAJOR.MINOR.PATCH), increment: MAJOR - when changing mechanical or connector interfaces MINOR - when changing schematic or layout PATCH - when changing BOM or sourcing data
77 parts - 2 layers85.6 × 54 mm

SnakeBusinessCard
alex1324575/snake-pcb-business-card
STM32-powered PCB business card with a 10x9 LED Snake game, USB-C power, and passive NFC. KiCad hardware, C firmware, and verification reports.
136 parts - 4 layers68.6 × 53.3 mm

Pcb main nautilus atmega4809
apcountryman/pcb-main-nautilus-atmega4809
A Microchip ATmega4809 based mainboard PCB.
91 parts - 4 layers150 × 110 mm

Controller
micthiesen/crystal-shim
Aquarium skimmer controller: capacitive sensing, ESP32-C6 firmware, and separated mains switching
117 parts - 6 layers82 × 155 mm

- 4 layers36.4 × 15 mm

- 4 layers70 × 60 mm

Questions
How big is the Fib PCB PCB?
It measures 44.5 × 46 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Fib PCB use?
55 parts, built around the XC2C64A-5VQG44C, ERJ3EKF1002V, RC0603JR-070RL and CC0603KRX7R7BB104. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Fib PCB KiCad files?
From the hulonoj/FiberOpticBoard repository on GitHub, at the commit this page was made from: the board is PCB_Files/Fib_PCB.kicad_pcb and its schematic PCB_Files/Fib_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Fib PCB design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).