4 layers99.7 × 85.1 mm
Motor controller hw
HEEV/motor-controller-2018
Sam Ellicott's and Isaac Jones's motor controller senior design project. Fall 2018-Spring 2019
179 parts4
2 layers22.9 × 13.2 mm
Voltage regulator module
HEEV/motor-controller-20184Sam Ellicott's and Isaac Jones's motor controller senior design project. Fall 2018-Spring 2019
- Size
- 22.9 × 13.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 14
- Nets
- 9
- Pads
- 41
- Tracks, vias
- 127, 10
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Sep 2018
- Updated
- 7 Oct 2019
Overview
Voltage regulator module is an open-source printed circuit board by HEEV, from the HEEV/motor-controller-2018 repository on GitHub. It is a 2-layer board of 22.9 × 13.2 mm with 14 parts on 9 nets, routed with 127 tracks and 10 vias.
Its parts include 6 capacitors, 4 resistors, 1 IC, 1 diode and 1 connector. It belongs with the robots and motor control and power boards of this library.
README
README.mdCedarville University: Modular Motor Controller Project
Senior Design project by Samuel Ellicott and Isaac Jones 2018-2019
You are in the hardware portion of the project, this contains the Kicad design files for the project and the schematics in PDF form. If you are looking for the software it is in the motor controller 2018 sw github repository.
This project’s goal is to provide the Cedarville University Supermileage team with a high-efficiency electric motor controller for use in any category of vehicle. The controller should be simple enough to use that a competent freshman or sophomore engineer on the team could set it up.
The controller is operated either by an analog throttle input or by the CAN interface exposed by the controller. Hopefully this makes the controler simple to use, but still capable of clever efficiency optimizations with some wizardry.
The Cedarville supermileage team competes in the Shell Eco-Marathon so the design must fit within the contstraints of their rules (at the time of this writting, 2019). This leads to the following constraints
- Maximum Nonminal Battery Voltage - 48V
- Peak Voltage - 60V
Therefore the controller was designed to fit these requirements and a new driver stage would need to be designed if these limits were exceeded.
Even though I have graduated I am still more than willing to answer questions about this project :-)
-Sam EllicottProject Organization
Overall, the project is organized into two gitub repositories. This one, devoted to the motor controller hardware (motor controller 2018) and the other one (motor controller 2018 sw) devoted to the motor controller software.
The actual hardware of the project is split into three PCBs (and three corresponding Kcad projects)
The hardware repository is split between three Kicad projects.
- motor-controller-hw: This somewhat poorly named project contains the files for the controller portion of the project (micocontroller, FOC algorithm chip, inputs, etc)
- MotorControllerPowerBoardRev2: This contains (somewhat obviously) the Kicad project for the power conversion part of the motor controller (FET driver chips, giant honking power MOSFETS, current sensing chips, etc). The power stage has four NFET half bridges and three hall-effect current sensing chips. The board can be configured to power a 3-phase motor or a brushed motor. Optionally for the brushed motor the half-bridges can be parralled to double the drive current capability.
- voltage-regulator-module: We were unable to find a commertially available 60V-to-5v DC-DC converter for the controller portion of the project that did not have significant lead time, so we rolled our own to fit a similar footprint to some DC-DC converters from Pololu. This is just a little daughter PCB that is soldered to the controller PCB.
The schematic files and PDF's of the PCB layout can be found in the pdf directory.
Software versions
For this project we used either Kicad version 5.0.1 or 5.0.2 (I cannot really remember), but it will probably work with any version of Kicad > 5.0.0
Parts
14| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 100n | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10u | Capacitor_SMD:CP_Elec_6.3x5.8 | C4 |
| 1 | 12K | Resistor_SMD:R_0805_2012Metric | R4 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 22u | supermileage_footprints:PCC-M0630M-LP | L1 |
| 1 | 33K | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 4.7u | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 4u7 | Capacitor_SMD:C_1210_3225Metric | C1 |
| 1 | 68K | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | D_Schottky_Small_ALT | Diode_SMD:D_SMA | D1 |
| 1 | LMR16010 | supermileage_footprints:SOIC-8-PowerPAD | U1 |
| 1 | Power | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
More from HEEV/motor-controller-2018
2- 4 layers100 × 100 mm
MotorControllerPowerBoard
HEEV/motor-controller-2018
Sam Ellicott's and Isaac Jones's motor controller senior design project. Fall 2018-Spring 2019
134 parts4
Similar boards
- 2 layers116.8 × 30 mm
Type d
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
14 parts3kApache-2.0 - 2 layers32 × 22 mm
- 2 layers34 × 45 mm
2032Charger
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
14 parts915 - 2 layers34 × 109.9 mm
- 2 layers45.3 × 42.7 mm
- 2 layers42.5 × 28.8 mm
C5VRX JACK DIY
Twotoz/C5VRX
Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS
14 parts515GPL-3.0 - 2 layers54 × 47 mm
- 2 layers62 × 24 mm
Questions
How big is the Voltage regulator module PCB?
It measures 22.9 × 13.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Voltage regulator module use?
14 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Voltage regulator module KiCad files?
From the HEEV/motor-controller-2018 repository on GitHub, at the commit this page was made from: the board is voltage-regulator-module/voltage-regulator-module.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Voltage regulator module design in my own project?
Its repository states no licence, so its author keeps all rights: ask HEEV before reusing the design.