
Led addon
HarkonenBade/batt
A 1S lipo charge/protect board based on the TP4056 and the FS312F

A 1S lipo charge/protect board based on the TP4056 and the FS312F
Batt is an open-source printed circuit board by HarkonenBade, from the HarkonenBade/batt repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 25 × 18 mm with 20 parts on 14 nets, routed with 120 tracks and 8 vias.
It is built around the FS312F-G, FS8205 and TP4056. Its parts include 8 connectors, 5 resistors, 3 capacitors, 3 ICs and 1 diode. It belongs with the power boards of this library.
A simple and compact TP4056 based LiPo charge and protection board.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R2, R3, R4 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 100r | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 2k4 | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | B+ | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J2 |
| 1 | B- | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J4 |
| 1 | BATT | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J3 |
| 1 | FS312F-G | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | FS8205 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | L+ | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J1 |
| 1 | L- | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J6 |
| 1 | LED | batt:TJ-S1615SW6TGLCRG-A5 | D1 |
| 1 | TP4056 | Package_SO:HSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.1mm | U3 |
| 1 | USB_B_Micro | batt:U254-051T-4BH83-F1S | J7 |
| 1 | V+ | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J5 |
| 1 | V- | batt:PinHeader_1x01_P2.54mm_Vertical_nosilk | J8 |

HarkonenBade/batt
A 1S lipo charge/protect board based on the TP4056 and the FS312F

cester-ino/OTTO-hardware
those specs refer to the tactile buttons version, but a led backlight button version is in the works too.

alxhoff/gameboy-dmg-pcb
PCB for Gameboy DMG with audio and GPIO expander to provide I2C interface to push buttons

aziraphale/pride-badge-v1
🌈⚡Pride badge PCB with LEDs, STM32, and 3D printed diffuser+case!





chof747/kitchen-helper-hardware
Hardware specs, schematics and pcb design for the kitchen helper device
It measures 25 × 18 mm and has 2 copper layers, 1.6 mm thick.
20 parts, built around the FS312F-G, FS8205 and TP4056. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the HarkonenBade/batt repository on GitHub, at the commit this page was made from: the board is docs/boards/batt.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).