Skip to the content
2 layers63.5 × 71.1 mmDomepcb, the printed circuit board in 3D

bits of pcb and models and covers for the dome. power and network goes in, WS2812 protocol comes out. also it might be dry.

Size
63.5 × 71.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
8
Nets
46
Pads
63
Tracks, vias
55, 8
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
26 May 2022
Updated
26 May 2022

Overview

Domepcb is an open-source printed circuit board by Hacks-R-Us, from the Hacks-R-Us/dome-hardware repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 63.5 × 71.1 mm with 8 parts on 46 nets, routed with 55 tracks and 8 vias.

Its parts include 4 connectors, 2 capacitors, 1 resistor and 1 IC.

README

README.md

dome-hardware

Bits of pcb and 3D model for the dome controllers, strips, and dome covering.

  • PCB: Power and network goes in, WS2812 protocol comes out.
  • Shims: go on PCB to stop things touching.
  • Toothpicks: go in ends of WS2812 strips and cable tie the cables to them to reduce strain on the strip ends.
  • Sheets: Patterns to cut (5 of) to make your dome into a covered dome. These are the raw patterns with none of the seams drawn. Good luck.

Jankyness

Yes, very. Some parts (such as pin bodges in the schematics) are very dirty hacks, even you can even call them that.

Do I need the softwarey things to open the stuff?

  • Yes.
  • FreeCAD
  • KiCAD

How to make things

  • PCBs: We used:
    • jlcpcb for the PCBs, they were cheap and fast and it worked.
    • Ebay for the parts. they were also cheap and fast and they worked.
  • 3D printed bits:
    • We used a Prusa i3MK3s for the 3D printed parts. It was expensive and slow and it worked. Really. printing 500 toothpicks took days.
    • Conveniently someone had Covid at the time so didn't go outside and could ensure the house didn't burn down. Thanks :)
  • For the covering, we used:
    • Sharpies
    • 3.8Oz/sqM waterproof ripstop nylon. (unknown amount maybe 30-40 meters of 1.5 wide?)
    • A giant compass...
    • plastic tent grommet/eyelets
    • 0.38mm thread (too thick!)
    • London hackspace's sewing machine.
    • ...later superseeded by stick with rusty nail and holes drilled at size of sharpie and length in drawing
    • A straight edge
    • Some LX tape (1 roll does it), and a LOT of time.
    • After measuring the first set out, we stuck it to the floor and the ripstop was thin enough it worked like tracing paper to draw the points...
    • This is probably the worst way of doing it.
    • A LOT OF TIME. REALLY. A LOT. WEEKS. (would have helped if we knew how to sew to start with!)

"I have a better way of..."

Nice. if it's elegant of slightly better, do a PR or something...

Parts

8
QtyValueFootprintReferences
2C_Polarized_USCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC1, C2
2Conn_01x20Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_VerticalJ2, J3
1Conn_01x03_FemaleConnector_Phoenix_MSTB:PhoenixContact_MSTBVA_2,5_3-G_1x03_P5.00mm_VerticalJ1
1Conn_02x05Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_VerticalJ4
1LD33CVPackage_TO_SOT_THT:TO-220F-3_Horizontal_TabDownU1
1RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1

Similar boards

  • 2 layers20.5 × 24.8 mmPi interface, the printed circuit board in 3D

    Pi interface

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    8 parts3.7k
  • 2 layers59.9 × 25.7 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    8 parts1kGPL-3.0
  • 2 layers52 × 12.6 mmUSB, the printed circuit board in 3D

    USB

    shanteacontrols/OpenDeck

    A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

    8 parts960Apache-2.0
  • 2 layers87.5 × 48.5 mm7 input macropad, the printed circuit board in 3D

    7 input macropad

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    8 parts915
  • 2 layers36.2 × 63.1 mmPicoMemcard pico, the printed circuit board in 3D

    PicoMemcard pico

    dangiu/PicoMemcard

    Emulating PSX Memory Card (or controller) using a Raspberry Pi Pico

    8 parts694GPL-3.0
  • 2 layers36 × 10 mmPCB4-PWR BTN Rev.A, the printed circuit board in 3D

    PCB4-PWR BTN Rev.A

    OLIMEX/DIY-LAPTOP

    Do It Yourself Open Source Hardware and Software Modular Hacker's Friendly Laptop

    8 parts578Apache-2.0

Questions

How big is the Domepcb PCB?

It measures 63.5 × 71.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Domepcb use?

8 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Domepcb KiCad files?

From the Hacks-R-Us/dome-hardware repository on GitHub, at the commit this page was made from: the board is domepcb.kicad_pcb and its schematic domepcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Domepcb design in my own project?

Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).