Brewingstation3 is an open-source printed circuit board by Gr3yh0und, from the Gr3yh0und/brewingstation repository on GitHub, published under the MIT licence. It is a 2-layer board of 100 × 80 mm with 51 parts on 62 nets, routed with 339 tracks and 1 via.
It is built around the BME680, MAX31865AAP+ and PCF8574T, with the CPM121, DS18B20-15(MY) and ESP32-C6-WROOM-1U-N8 among its other parts. Its parts include 19 connectors, 17 resistors, 5 ICs, 2 switches and 1 transistor. It belongs with the home automation and IoT boards and the ESP32, ESP8266 and RISC-V boards of this library.
Firmware, hardware, and PCB design for a DIY automated beer brewing controller. An ESP32-based device reads mash temperature from multiple sensors, drives a GGM IDS2 induction cooktop through PID control, and integrates with CraftBeerPi via MQTT.
This repo tracks the project's evolution across several hardware/firmware generations.
Credit: the GGM IDS2 induction cooktop's RS232/serial protocol — pulse timings, command frames, power levels, and error codes — was reverse-engineered by InnuendoPi in MQTTDevice2. Every generation in this repo builds on that work.
Full rewrite: PID mash control, multi-sensor support, safety shutdowns, brew timer, KiCad schematic, 3D-printable case. See README, HARDWARE.md, BOM.md, CASE.md.
brewingstation carries a platformio.ini (src_dir = .) alongside its .ino, so both PlatformIO and the Arduino IDE build from the same source file — pick whichever toolchain you prefer.
All generations share the same core idea: control the GGM IDS2 induction cooktop over its proprietary serial protocol, read temperature from DS18B20/PT100/PT1000/BME sensors, drive a couple of OLED displays and status LEDs, and talk to CraftBeerPi over MQTT.
brewingstation3 is where active development happens; the earlier folders are kept as historical/reference hardware revisions. It is work in progress: firmware compiles but is not yet proven on real hardware — the PCB hasn't been soldered/assembled, nothing has been tested end-to-end, and the 3D-printable case hasn't been printed.
Getting started
Each own-project folder is self-contained with its own README and config. In general:
Pick a generation — brewingstation3 for new builds, the earlier folders for reference or repairing existing hardware.
Copy config_example.h (or include/config_example.h for brewingstation3) to config.h and fill in your MQTT/OTA settings (brewingstation3 also provisions WiFi separately, via a WiFiManager captive portal on first boot — see its README). config.h is gitignored — never commit real credentials.
Build with PlatformIO (pio run) or open the .ino directly in the Arduino IDE — see that folder's README for board-specific notes.
brewingstation3 has a native unit test suite for its hardware-independent logic (calibration math, button-ladder mapping, induction error codes) — runs on the host, no ESP32 toolchain or device required:
Open-source ESP32-C6 beehive monitoring hub for scales and sensors. Collects weight, climate, sound, vibration and bee traffic from up to 16 hives, with BLE, OTA, FastAPI/PostgreSQL backend, dashboards, MQTT and tested…
A stackable carrier board for the Adafruit MAX31865 RTD-to-digital converter. Each board hosts up to 8 MAX31865 modules and multiple boards can be stacked on brass standoffs to scale the channel count without changing…
Minino is an original multiprotocol and multiband board made for sniffing, communicating, and attacking IoT devices. It was designed as a mini Cat that integrates the powerful ESP32C6, GPS, microSD and OLED.
Fencing Tester is a tool for testing and analysing basic fencing equipment. It is intended for situations where you may not have access to a full piste setup to test equipment during repair or when you are tired of…
This repository hosts the source code, electrical schematics and layout, as well as documentation developed by Emil Eensaar for his Bachelor of Science thesis.
A collection of custom PCB designs created in KiCAD, centered around the Raspberry Pi Pico (RP2040) platform. Each board is a standalone module that connects to the Main Board and extends its functionality via I2C, SPI…
147 parts
Questions
How big is the Brewingstation3 PCB?
It measures 100 × 80 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Brewingstation3 use?
51 parts, built around the BME680, MAX31865AAP+, PCF8574T and CPM121. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Brewingstation3 KiCad files?
From the Gr3yh0und/brewingstation repository on GitHub, at the commit this page was made from: the board is brewingstation3/kicad/.history/brewingstation3.kicad_pcb and its schematic brewingstation3/kicad/.history/brewingstation3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Brewingstation3 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).