2 layers124 × 67 mm
2 layers41 × 39 mm
Panel4
goktugh/robotbitsSome bits for robots or other control applications
- Size
- 41 × 39 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 52
- Nets
- 11
- Pads
- 172
- Tracks, vias
- 440, 68
- Pours
- 12
- Routed
- Yes
- KiCad
- KiCad 5 (file 20210126)
- Created
- 18 Mar 2022
- Updated
- 25 Feb 2022
Overview
Panel4 is an open-source printed circuit board by goktugh, from the goktugh/robotbits repository on GitHub. It is a 2-layer board of 41 × 39 mm with 52 parts on 11 nets, routed with 440 tracks and 68 vias.
It is built around the ATTINY4-TSH, DRV8837DSGR-MS and AIC1734-33GUTR. Its parts include 16 connectors, 12 capacitors, 12 ICs, 8 resistors and 4 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3
ATTINY4-TSH
SOT-23-6-40℃~+85℃ 1.8V~5.5V 12MHz 32Byte 4 512Byte 8 Bit AVR Built-in FLASH SOT-23-6 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)DRV8837DSGR-MS
WSON-8-EP(2x2)-40℃~+125℃ 1.5A 1.8V~7V 17nA 650mΩ Yes WSON-8-EP(2x2) Brushed DC Motor Drivers ROHSMSKSEMIBrushed DC Motor Drivers
AIC1734-33GUTR
SOT-23-40℃~+85℃@(Ta) 1 12V 3.3V 300mA 470mV@(300mA) 55uA Fixed Over Current Protection、Over Temperature Protection Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
Parts
52| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R1, R1, R1, R2, R2, R2, R2 |
| 8 | 1uF | Capacitor_SMD:C_0402_1005Metric | C2, C2, C2, C2, C3, C3, C3, C3 |
| 8 | Conn_01x01_Male | motorback:motorpad | J2, J2, J2, J2, J3, J3, J3, J3 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C1, C1, C1 |
| 4 | AIC1734-33GUTR | Package_TO_SOT_SMD:SOT-23 | U3, U3, U3, U3 |
| 4 | ATtiny4-TS | Package_TO_SOT_SMD:SOT-23-6 | U2, U2, U2, U2 |
| 4 | DRV8837DSGR | motorback:drv8837_custom | U1, U1, U1, U1 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D1, D1, D1, D1 |
| 4 | Servo wire input | Connector_JST:JST_SH_SM03B-SRSS-TB_1x03-1MP_P1.00mm_Horizontal | J1, J1, J1, J1 |
| 4 | prog_pins | motorback:pogopins_5 | J4, J4, J4, J4 |
More from goktugh/robotbits
12- 2 layers124 × 67 mm
- 4 layers83.5 × 61 mm
- 4 layers82 × 56.5 mm
- 4 layers82 × 61 mm
- 2 layers110 × 48 mm
- 4 layers32 × 58 mm
- 2 layers52 × 52 mm
- 2 layers77 × 39 mm
- 4 layers19 × 32 mm
- 2 layers43.5 × 15 mm
- 2 layers49.6 × 41.3 mm
Similar boards
- 2 layers19 × 24.1 mm
- 2 layers19 × 24.1 mm
Malenki nanox
MarkR42/malenki-esc
A small electronic speed controller for e.g. tiny fighting robots or other rc models
25 parts7 - 2 layers
- 2 layers22 × 13 mm
Sl56660
sittner/sl56660
The Fairchild SL56660 is one of the small set of logic building blocks the Cray-1 supercomputer (1976) was made of: a dual NAND gate (one 5-input, one 4-input) with complementary outputs, implemented in emitter-coupled…
25 partsCERN-OHL-W-2.0 - 2 layers15.2 × 10.2 mm
- 2 layers20.3 × 69.7 mm
PG attiny404
fabiansteiner/OpenValve
3D-printable pinch valve for irrigation and sensor-driven liquid control.
41 parts276CERN-OHL-S-2.0 - 6 layers158 × 174 mm
TritonECU Main
alpauna/TritonECU
ESP32-S3 engine control unit — fuel injection, ignition timing, wideband O2 (CJ125/LSU 4.9), dashboard, and MQTT telemetry
457 parts10 - 4 layers68.6 × 53.3 mm
101 PCB
ICRS/101
The all-new open source Robotics 101 course from ICRS. It's specifically designed to be run in hackspaces, after school clubs and university societies.
89 parts10CC-BY-4.0
Questions
How big is the Panel4 PCB?
It measures 41 × 39 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Panel4 use?
52 parts, built around the ATTINY4-TSH, DRV8837DSGR-MS and AIC1734-33GUTR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panel4 KiCad files?
From the goktugh/robotbits repository on GitHub, at the commit this page was made from: the board is n20_motorback/motorback_panel4/panel4.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panel4 design in my own project?
Its repository states no licence, so its author keeps all rights: ask goktugh before reusing the design.