

Atari 8-Bit Bus EXtender
- Size
- 143 × 162 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 91
- Pads
- 430
- Tracks, vias
- 2,516, 206
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 25 May 2019
- Updated
- 1 Nov 2025
Overview
Abex is an open-source printed circuit board by gianlucarenzi, from the gianlucarenzi/abex repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 143 × 162 mm with 40 parts on 91 nets, routed with 2,516 tracks and 206 vias.
Its parts include 9 capacitors, 8 connectors, 6 ICs, 4 resistors and 1 diode. It belongs with the retro computing and games boards of this library.
README
README.mdAtari Bus EXtender for Atari XE Computers
This is a Atari PBI & ECI Bus extender, for adding expansion board with ease, called Atari Bus EXtender for Atari XE Computers or ABEX for short.
This project expand somehow the Atari 1090XL Bus Expansion in the early 80s but with a simple layout and using only 3.3v compliant electronics. No 5V is available on the bus, and all signals are converted to 3.3v level.
The Bus recall somehow the AteoBus from Amiga 1200 Computers but using a more common nowadays PCI-Express Bus Slots with 64 pins.
Right now there are 2 boards desinged for this bus:
1- Atari DUO Cart (a porting of the famous Uno-Cart Project)
2- Atari MegaRAM (a PortB PIA Emulator) with 1024K RAM memory banked
More boards can be added as soon they do not interfere with the others like using the PBI Protocol device in available in ROM. For example a simple RS232 Board can be designed using a STM32F407 as port EXPANDER with R: handler in internal flash, or a SDCard Hard Drive Simulator can be designed as well.
Even WiFi or Ethernet Controller can be achived flawlessly.
Everything is up to you, using your mind to open the world to this wonderful machine like Atari 130XE.
Rendered Images
Front
Back
Overall
Hardware License
Copyright (C) 2018/2019 Gianluca Renzi gianlucarenzi@eurek.it icjtqr@gmail.com
The hardware of this project is released as free/open hardware under the
Creative Commons Attribution Share-Alike license. See LICENSE.hw for details.
Firmware License
Copyright (C) 2019 Gianluca Renzi icjtqr@gmail.com
The microcontroller firmware of this project is released as free software,
under the terms of the GNU General Public License v3, or later. See
LICENSE.sw for details.
Software License
The host software (amigafloppy tool) is released as free software, under the
terms of the GNU General Public License v3, or later. See LICENSE.sw or licence.txt for
details.
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | TXB0108-PW | Housings_SSOP:SSOP-20_4.4x6.5mm_Pitch0.65mm | U1, U3, U4, U5, U6 |
| 4 | 10u | Capacitors_SMD:C_1206_HandSoldering | C1, C7, C8, C9 |
| 4 | Conn_01x01 | MountingHole:MountingHole_3mm | J4, J5, J6, J7 |
| 4 | TEST_1P | Pin_Headers:Pin_Header_Straight_1x01 | GND1, VCC_5V1, W1, W2 |
| 3 | 0 | Resistors_SMD:R_1210_HandSoldering | R2, R3, R4 |
| 3 | 0877159106 | 0877159106:MOLEX_0877159106 | J1, J2, J3 |
| 3 | 10u | RetroBitLab:CP_Radial_D10.0mm_P2.50mm_3D | C4, C5, C6 |
| 1 | 1.5K | Resistors_SMD:R_1210_HandSoldering | R1 |
| 1 | 100n | Capacitors_SMD:C_1206_HandSoldering | C2 |
| 1 | 22u | Capacitors_Tantalum_SMD:TantalC_SizeA_EIA-3216_HandSoldering | C3 |
| 1 | ATARI-CARTRIDGE | RetroBitLab:TE_5530843-2_15X2_CART_EDGE_CONNECTOR | CART2 |
| 1 | ATARI-CARTRIDGE | RetroBitLab:ATARI-LEFT-CARTRIDGE | CART1 |
| 1 | CONN_01X04 | Pin_Headers:Pin_Header_Angled_1x04 | P1 |
| 1 | ECIBUS | RetroBitLab:ECI_BUS_7X2_EDGE_CONNECTOR | ECI2 |
| 1 | ECIBUS | RetroBitLab:ATARI-XE-ECI-SLOT | ECI1 |
| 1 | LED GREEN | LEDs:LED_1206 | D1 |
| 1 | LOGO | RetroBitLab:ABEX_Logo_22mmx11mm_WB | LOGO |
| 1 | LOGO | RetroBitLab:atari_fuji_SilkScreen_21.2x25-Rev | ATARILOGO |
| 1 | MCP1827S-1.5A-TO-220-3 | RetroBitLab:MCP_1827S_TO-220-3_Horizontal_TabDown | U2 |
| 1 | Symbol_GNU-GPL_CopperTop_Small | RetroBitLab:Symbol_GNU-GPL_SilkScreen_Small | GPL |
The 39 most common of 40 parts.
Similar boards
- 2 layers139.7 × 73.7 mm

- 2 layers149.4 × 177.4 mm

Lightsculpture
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
40 parts915 - 2 layers150 × 50 mm

EleLab v2 Bus150
Chrismettal/EleLab_v2
Cheap DIY lab system for hobbyists and the tinkering folk
40 parts531GPL-3.0 - 2 layers66.4 × 48.1 mm

Raspberry
Chrismettal/flipper-zero-backpacks
Backpack-style addon boards for the Flipper Zero!
40 parts456 - 2 layers44 × 44 mm

- 2 layers90.8 × 53.3 mm

- 2 layers59.6 × 109.5 mm

Drop
ohmtech-rdi/eurorack-blocks
Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust
40 parts410 - 2 layers123.8 × 73.5 mm

Questions
How big is the Abex PCB?
It measures 143 × 162 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Abex use?
40 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Abex KiCad files?
From the gianlucarenzi/abex repository on GitHub, at the commit this page was made from: the board is abex.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Abex design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).